Asko CC4727S / 4000 Bedienungsanleitung

Instructions for use

Built-in unit

CC4727S / 4000

CC4927S / 4000

CC41227S / 4000

EN Manual EN 3 - EN 13

Pictograms used:

Important information

Tip

EN 3

CONTENT

Built-in unit

Description 4

Introduction 4

Use

Controls 5

Maintenance

Cleaning 7

Removing the grease filters 8

Replacing the carbon filter 8

Changing the light bulbs 8

Installation

General 9

Electrical connection 10

Mounting the built-in unit 11

Technical specification

Appendix

Disposal of appliance and packaging 13

EN 4

Description

A Switch fan on/off

B Reduce extractor capacity

C Increase extractor capacity

D Engage intensive mode

E Clean air function/filter indication

F Timer function

G Switch lighting on/off

H Dim lighting

I Display

Introduction

This user manual gives you a quick overview of all the possibilities

offered by the appliance. You will find information on safety measures

and maintaining the appliance.

Please retain this user manual and the installation guide.

They may be of use to future users of the appliance.

Declaration of conformity

We declare that our products meet the applicable European Directives,

Decisions and Regulations and the requirements listed in the standards

referenced.

Read the separate safety instructions before

using the device!

YOUR BUILT-IN UNIT

EN 5

USE

Controls

Switching the fan on and off

• Switch the fan on with the on/off button (A) and select the desired

extractor setting with buttons ‘B’ and ‘C’.

The ‘I’ display indicates which setting has been selected.

• Use button ‘D’ to switch on the intensive setting.

“HI” appears in the ‘I’ display.

After 6 minutes the intensive mode is automatically reduced to the

setting previously selected.

Switching the lighting on and off

• Use the ‘G’ button to switch the lighting on and off.

Dimming the lighting

• Dim the lighting with button ‘H’.

The strength of the lighting varies between maximum and minimum,

and vice-versa.

Clean Air function:

With the Clean Air function you can refresh the air in the kitchen

over maximum 24 hours.

• Make sure the built-in unit has been switched off.

• Press on the Clean Air button ‘E’.

Every hour, the extractor hood will switch on for 10 minutes

automatically, at the lowest extraction setting. The display reads

“24” and an indicator flashes at the bottom right.

EN 6

USE

Switching on the timer

• Switch on the extractor hood with button ‘A’.

• Set the extraction strength with buttons ‘B’ and ‘C’.

• Press the Timer button ‘F’.

The extractor hood switches off automatically after 30 minutes.

Switch off the Timer function by pressing button ‘F’ again, or by

switching off the extractor hood with button ‘A’. The display shows

the selected speed and the remaining time.

Grease filter indicator

After 100 hours of use the “FF” indicator is shown in the display.

• Clean the grease filters.

• Reset the filter indicator. While the hood is switched off, press

button ‘E’ for 3 seconds until the filter indicator disappears.

Carbon filter indicator

After 200 hours of use the “EF” indicator is shown in the display.

• Replace the carbon filters.

• Reset the filter indicator. While the hood is switched off, press

button ‘E’ for 3 seconds until the filter indicator disappears.

EN 7

Cleaning

Attention! Before performing any maintenance operation, isolate the

hood from the electrical supply by switching off at the connector and

removing the connector fuse. Or if the appliance has been connected

through a plug and socket, then the plug must be removed from the

socket.

The built in unit should be cleaned regularly (at least with the same

frequency with which you carry out maintenance of the fat filters)

internally and externally. Do not use abrasive products. Do not use

alcohol!

Attention! Failure to carry out the basic cleaning recommendations of

the built in unit and replacement of the filters may cause fire risks.

Therefore, we recommend oserving these instructions.

The manufacturer declines all responsibility for any damage to the

motor or any fire damage linked to inappropriate maintenance or failure

to observe the above safety recommendations.

Built in unit

Clean the built in unit with soapy water and a soft cloth. Then wipe

with clean water to rinse. Do not use aggressive cleaning agents such

as soda. The built in unit paintwork will stay looking nice if you wax it

occasionally.

Stainless steel canopy hoods

Do not use any sort of scourer. Treat with a stainless steel care product

and polish with the structure of the stainless steel.

Metal grease filters

These must be cleaned once a month (or when the filter saturation

indication system – if envisaged on the model in possession – indicates

this necessity) using non aggressive detergents, either by hand or in

the dishwasher, which must be set to a low temperature and a short

cycle. The openings must be placed downwards to let the water run

out of the filters. The cleaning agents will make the aluminium filter turn

dull, this is normal.

MAINTENANCE

EN 8

Grease filters

Removing the grease filters

Switch off the electricity! Remove the plug from the socket or switch

the electricity off at the mains. Open the panel and pull the special

handle to remove the filter.

Replacing the carbon filter

The carbon filter must always be used if the built in unit is not ducted.

1. Open the panel.

2. Remove the grease filters.

3. Fit the carbon filter by wedging it into the casing (D).

4. Replace the filter grids in the extractor hood.

Note:

• Saturation of the activated charcoal will eventually occur after more

or less prolonged use, depending on the type of cooking and how

frequently the grease filter is cleaned.

• In all cases it is necessary to replace the cartridge at least every

four months.

• DO NOT wash or reuse the carbon filter. Saturated carbon is not

environmentally friendly, change the filter regularly.

Lighting

Changing the light bulbs

Faulty LEDs must be replaced by a professional installer.

MAINTENANCE

EN 9

INSTALLATION

General

This appliance should be connected to the power supply by a

recognized fitter who is familiar with, and works according to the

correct safety regulations. This appliance meets the European

requirements.

Important that you know:

• The minimum distance between the supporting surface for the

cooking vessels on the gashob and the lowest part of the range

hood must be not less than 65 cm. For use with an electric, ceramic

or induction hob, this distance must be at least 55 cm.

• If the built in unit is to be fitted to an existing duct no other

appliances, such as a geyser or heater, may be connected to that

same duct.

• Consider local regulations with respect to the ventilation of gas

appliances.

• The shorter the duct, and the fewer the bends in it, the better the

built in unit will work.

• Before you start drilling check that there are no installation cables

present.

• The connecting pipe for the built in unit has a diameter of 120 or

150 mm. It is best also to use a flue pipe of the same diameter.

• The installation material supplied with this range hood is designed

for fixing to reinforced concrete or masonry walls. For some types

of walls you may need special plugs and screws.

EN 10

INSTALLATION

Electrical connection

This appliance is manufactured in class I, it must therefore be

connected to the earth system.

Make sure the supply voltage ratings correspond with those stated on

the appliance data plate. The connection to the mains is carried out as

follows:

BROWN = phase L

BLUE = phase N

YELLOW/GREEN = Earth

During the electrical connection make sure that the electrical socket is

equipped with earth connection.

This canopy hood has been provided with a power plug. When installing

the hood, make sure that this plug remains accessible.

Attention:

If you want to make a fixed connection, ensure that a multi-pole switch

with a distance between contacts of 3 mm is installed in the supply

cable.

max. 100 mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Asko Dunstabzugshaube Handbücher

Asko

Asko WS90CNTHJ Bedienungsanleitung

Asko

Asko CCT1252WC Bedienungsanleitung

Asko

Asko CBB861S Bedienungsanleitung

Asko

Asko CD4634B/4000 Bedienungsanleitung

Asko

Asko CW4939S/WS90FETGG Bedienungsanleitung

Asko

Asko CW4930G Bedienungsanleitung

Asko

Asko CC4527S Bedienungsanleitung

Asko

Asko CW4934S/4000 Bedienungsanleitung

Asko

Asko CCT1252W Bedienungsanleitung

Asko

Asko CW4611 Bedienungsanleitung

Asko

Asko CBB761S Bedienungsanleitung

Asko

Asko CCT9051S Bedienungsanleitung

Asko

Asko CBB862WC Bedienungsanleitung

Asko

Asko CW4938GCN Bedienungsanleitung

Asko

Asko WS90 BAM Series Bedienungsanleitung

Asko

Asko CG1 Bedienungsanleitung

Asko

Asko CO4927S Bedienungsanleitung

Asko

Asko CBB862W Bedienungsanleitung

Asko

Asko CW4634S/4000 Bedienungsanleitung

Asko

Asko ES1011QAM Bedienungsanleitung

Asko

Asko CBB901SB Bedienungsanleitung

Asko

Asko CCT9051SC Bedienungsanleitung

Asko

Asko CW4931 Bedienungsanleitung

Asko

Asko CW4936S Bedienungsanleitung

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung

Nibe

Nibe S Series Benutzerhandbuch