ASL INTERCOM INTEGRA Bedienungsanleitung
INTEGRA Products
Wall-Mount Instructions
Observe all safety information both on the equipment and in in the Safety and Precautions.
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 1 of 16
This document only provides instructions to mount the INTEGRA to the wall.
Ensure you refer to the full INTEGRA Installation Guide for correct installation and wiring details.
For all user documentation please go to www.asl-control.co.uk/downloads or scan the QR code.
Do not try to move or unpack an assembled unit without assistance.
The INTEGRA is heavy:
•Max. > 30 kg for the back box (and door) only
•Max. > 45 kg with the Electronics Module fitted
•Max. > 95 kg with the Electronics Module and both backup batteries fitted
It may take two or more people to install the Back Box with Electronics Module fitted.
1 Installing the Wall-Mount Frame
1. Undo 6 x M6 nuts (A) securing the back box to the wall-mount frame.
2. Undo 4 x M6 nuts (B) securing the Electronics Module to the wall-mount frame (if not already done).
3. Undo the 6 x M8 hex head screws securing the battery tray to the back box and wall-mount frame (C).
B
B
B
B
C
C
C
C
C
C
A
A
Do not remove the transit
screws if not removing the
Electronics Module.
A
A
A
A
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 2 of 16
1 Installing the Wall-Mount Frame
The INTEGRA is heavy (max. > 95 kg with batteries fitted).
It is VITAL that it is mounted to suitably robust walls or structures using appropriate fixing for the
specific wall type.
4. Prepare the wall-mount holes appropriately using the wall-mount frame to mark the hole positions (shown
below).
5. Secure the wall-mount frame to the wall.
Ensure that the frame is correctly oriented as shown below.
TOP
BOTTOM
A = ∅7.5 mm
A
A
A
A
A
A
A
A
A
A
394 mm
479 mm
394 mm
197 mm
197 mm
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 3 of 16
2 Installing the Back Box with Electronics Module Fitted
The INTEGRA is heavy:
•Back box only: max. > 30 kg
•Back box + Electronics Module: max. > 45 kg
It may take two or more people to install the Back Box with Electronics Module fitted.
1. Remove all knock-outs (∅20 mm) required for the external wiring (A).
Care should be taken to prevent swarf falling into the Field Termination Board, the Electronics
Module, the Network Switch (if fitted), the circuit breaker and any wiring connections.
A
A
A
(Door not shown for clarity)
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 4 of 16
2 Installing the Back Box with Electronics Module Fitted
2. Secure the back box to the wall-mount frame using the 6 x M6 nuts and washers (A).
Always ensure that adequate ventilation is provided for the equipment.
Do not block side or front vents and do not obstruct air flow behind enclosure.
Ensure that all swarf is removed from back box.
3. Secure the Electronics Module to the wall-mount frame using 4 M6 nuts and washers (B).
4. Secure the Battery Tray to the back box using the 6 x M8 hex head screws and washers (C).
1) Take care to not trap any cabling.
2) Ensure that the 6 x M8 hex head screws are fully tightened so that all the battery weight is
held by the wall-mounting frame and fixings, not by the back box.
3) The back box is not designed to support the battery weight.
Ensure you refer to the full INTEGRA Installation Guide for correct installation of the mains supply, field
wiring, optional items (if any) and batteries.
For all user documentation please go to www.asl-control.co.uk/downloads or scan the QR code on
page 1.
B
B
B
C
C
C
C
A
A
A
A
A
M6 Nut
Shakeproof
washer
Plain washer
Shakeproof
washer
M8 Hex Head
Screw
B
A
C
C
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 5 of 16
3 Installing the Back Box with Electronics Module Removed
3.1 Removing the Electronics Module
The Electronics Module can be removed from the back box for ease of wall installation.
The Electronics Module should be removed from the back box to install Interface Cards (LSZDC and/or
V2000-STBY), set the standby amplifier links, or install a Network Switch.
Removing the Electronics Module is NOT required if the INTEGRA is pre-configured with all required
modules (Interface Cards, amplifiers and optional items).
INTEGRA is heavy without the batteries but with the Electronics Module fitted (max. > 45 kg).
It may take two or more people to install the Back Box with Electronics Module fitted.
1. Unlock and open the unit’s door.
2. Disconnect the ribbon cables from the headers on the left-hand side of the Electronics Module (A).
Headers
Ribbon
cables
A
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 6 of 16
3 Installing the Back Box with Electronics Module Removed
3.1 Removing the Electronics Module
3. Disconnect the mains cable from the Electronics Module (A).
4. Disconnect the battery cable from the Electronics Module by undoing two strain-relief screws (B).
5. Disconnect the white power supply wiring from the Field Termination Board (C).
Do not disconnect the red power supply wiring from the Field Termination Board.
6. Disconnect the thermistor cable from the Electronics Module (D).
A
Disconnect
the WHITE
wiring only.
WHITE
RED
Thermistor
cable
C
D
B
Undo
2 x captive
screws using a
small flat-blade
screwdriver.
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 7 of 16
3 Installing the Back Box with Electronics Module Removed
3.1 Removing the Electronics Module
7. If fitted, disconnect all patch leads (3 x yellow, 2 x blue and 10 x grey) from the Electronics Module (A).
8. Disconnect the red RJ45 patch lead from the Electronics Module (B).
9. If a Hirschmann Network Switch is fitted, disconnect the blue patch lead from the Electronics Module.
10. Remove the Electronics Module by:
a. Undoing 4 x M5 hex head
transit screws (A).
b. Undoing 4 x M6 nuts (B).
A
B
B
B
B
B
A
A
A
A
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 8 of 16
3 Installing the Back Box with Electronics Module Removed
3.2 Installing the Back Box
1. Remove all knock-outs (∅20 mm) required for the external wiring (A).
Care should be taken to prevent swarf falling into the Network Switch (if fitted), the circuit breaker,
the fans and any wiring connections.
Care should be taken to prevent swarf falling into the Field Termination Board, the Electronics
Module, the Network Switch (if fitted), the circuit breaker and any wiring connections.
A
A
A
(Door not shown for clarity)
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 9 of 16
3 Installing the Back Box with Electronics Module Removed
3.2 Installing the Back Box
2. Secure the back box to the wall-mount frame using the 6 x M6 nuts and washers (A).
Always ensure that adequate ventilation is provided for the equipment.
Do not block side or front vents and do not obstruct air flow behind enclosure.
Ensure that all swarf is removed from back box.
3. Secure the Battery Tray to the back box using the 6 x M8 hex head screws and washers (B).
1) Take care to not trap any cabling.
2) Ensure that the 6 x M8 hex head screws are fully tightened so that all the battery weight is
held by the wall-mounting frame and fixings, not by the back box.
3) The back box is not designed to support the battery weight.
B
B
B
B
A
A
A
A
M6 Nut
Shakeproof
washer
Plain washer
Shakeproof
washer
M8 Hex Head
Screw
A
B
B
A
INTEGRA Products - Wall-Mount Instructions
U-0732-0142 (M0732_31) – Issue 01 Application Solutions (Safety and Security) Limited Page 10 of 16
3 Installing the Back Box with Electronics Module Removed
3.3 Re-fitting the Electronics Module
Ensure all required hardware configuration (e.g. fitting surveillance cards and amplifier, and setting
standby amplifier links and DIP switches) and optional item installation (e.g. Network Switch and
BMB01 Remote I/O Unit) are carried out before fitting the Electronics Module into the Back Box. Please
refer to the full INTEGRA Installation Guide for instructions.
1. Take the Electronics Module and carefully fit it into position in the back box, aligning the four mounting
holes with the four M6 studs projecting through from the wall-mount frame.
Take care that the mousehole cutout on the botton of the Electronics Module engages neatly over
the fan cable, ensuring that the fan cable is not crushed (A).
2. Secure the Electronics Module to the back box using 4 x M6 nuts and washers (B)
3. Fit 4 x M5 hex head transit screws and washers (C).
B
B
B
B
C
C
C
C
M6 Nut
Shakeproof
washer
Plain washer
Shakeproof
washer
M5 Hex Head
Screw
Engage the mousehole cutout
neatly over the fan cable.
Do not crush the fan cable!
A
Dieses Handbuch passt für folgende Modelle
11
Inhaltsverzeichnis
Andere ASL INTERCOM Verstärker Handbücher
ASL INTERCOM
ASL INTERCOM V2000 Bedienungsanleitung
ASL INTERCOM
ASL INTERCOM V2000 Bedienungsanleitung
ASL INTERCOM
ASL INTERCOM V400 Bedienungsanleitung
ASL INTERCOM
ASL INTERCOM DAX200 Bedienungsanleitung
ASL INTERCOM
ASL INTERCOM iPAM400 Bedienungsanleitung
ASL INTERCOM
ASL INTERCOM ROXX Series Bedienungsanleitung
