ASROCK A55F2-M4 Bedienungsanleitung

A55F2-M4USERMANUAL

The information in this document is subject to change without notice. The

manufacturer makes no representations or warranties with respect to the contents

hereof and specifically disclaims any implied warranties of merchantability or

fitness for any particular purpose. The manufacturer reserves the right to revise this

publication and to make changes from time to time in the content hereof without

obligation of the manufacturer to notify any person of such revision or changes.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna

•Increase the separation between the equipment and the receiver

•Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

•Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with

this equipment to ensure compliance with the pertinent RF emission limits

governing this device. Changes or modifications not expressly approved by the

system’s manufacturer could void the user’s authority to operate the equipment.

FederalCommunicationsCommission(FCC)

Disclaimer

DeclarationofConformity

This device complies with part 15 of the FCC rules. Operation is subject to the follow-

ing conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference

that may cause undesired operation.

Limits and methods of mesurement of radio disturbance char-

acteristics of information technology equipment

EN 55022

EN 61000-3-2 Disturbances in supply systems caused

EN 61000-3-3 Disturbances in supply systems caused by household appli-

ances and similar electrical equipment “ Voltage fluctuations”

EN 55024 Information technology equipment-Immunity characteristics-

Limits and methods of measurement

EN 60950 Safety for information technology equipment including electri-

cal business equipment

CE marking



This device is in conformity with the following EC/EMC directives:

A55F2-M4USERMANUAL

TABLE OF CONTENTS

Preface i

Brief Introduction 1

Specifications......................................................................................1

Motherboard Components................................................................3

Header Pin Definition and Jumper Settings.........................................4

I/O Ports...............................................................................................6

Multi-language Quick Installation Guide 7

English..................................................................................................7

Brazilian Portuguese..........................................................................9

Hindi....................................................................................................................11

French......................................................................................................13

Deutsch................................................................................................15

Russian................................................................................................17

Spanish................................................................................................19

Indonesian.............................................................................................21

Arabic.......................................................................................................23

Simplified Chinese...............................................................................25

Korean......................................................................................................27

A55F2-M4USERMANUAL

Brief Introduction

CPU

Specifications

• AMD A55 Chipset

Chipset

• Dual-channel DDR3 memory architecture

• 2 x 240-pin DDR3 DIMM sockets support up to 32 GB

• Supports DDR3 1866/1600/1333 MHz DDR3 SDRAM

Memory

• 1 x PCI Express x16 Gen2 slot

• 1 x PCI Express x1 slot

• Supported by AMD A55 Chipset

- 4 x Serial ATA 3Gb/s connectors

Expansion

Slots

Storage

• 1 x PS/2 keyboard and PS/2 mouse connectors

• 4 x USB 2.0 ports

• 1 x RJ45 LAN connector

• 1 x HDMI port (optional)

• 1 x D-sub (VGA) port

• 1 x Audio port (Line in, microphone and Line out)

Rear Panel I/O

• Socket FM2 for AMD A series processors

• Supports CPU up to 100W TDP

Note: Please go to ECS website for the latest CPU support list.

• 1 x 24-pin ATX Power Supply connector

• 1 x 4-pin 12V Power connector

• 1 x 4-pin CPU_FAN connector

• 1 x 3-pin SYS_FAN connector

• 2 x USB 2.0 headers support additional four USB 2.0 ports

• 4 x Serial SATA 3Gb/s connectors

• 1 x COM header

• 1 x Case open header

• 1 x Front Panel audio header

• 1 x Front Panel switch/LED header

• 1 x Speaker header

• 1 x Clear CMOS jumper

• 1 x Front panel USB power select jumper

• 1 x Rear USB/PS2 power select jumper

• 1 x Debug Card header (LDC)

• 1 x SPDIF out header

Internal I/O

Connectors &

Headers

• VIA VT1705CF 6-Ch High Definition audio CODEC

- Compliant with HD audio specification

Audio

LAN • Realtek RTL8111G Gigabit LAN

• Co-lay with Realtek RTL8106 10/100 LAN

Note: Please go to ECS website for the latest memory support list.

A55F2-M4USERMANUAL

QR Code for the complete manual download

on ECS website: http://www.ecs.com.tw

• AMI BIOS with 32Mb SPI Flash ROM

- Supports Plug and Play, STR (S3)/STD (S4)

- Supports ACPI & DMI

- Supports Hardware Monitor

- Audio, LAN, can be disabled in BIOS

- F7 hot key for boot up devices option

- Supports Over-Clocking

- Supports PaUp clear CMOS Hotkey (Has PS2 KB Model only)

- Supports Dual/Triple Display

- Supports EZ BIOS

- Supports Multi-Languange

- Supports AC’97/HD Audio auto detect (default)

System BIOS

Form Factor • Micro ATX Size, 210mm x 180mm

• Supports eBLU*/eDLU/eSF*

AP Support

Note: *Microsoft .NET Framework 3.5 is required.

A55F2-M4USERMANUAL

Motherboard Components

Table of Motherboard Components

LABEL COMPONENTS

1. CPU Socket Socket FM2 for AMD A series processors

2. SYS_FAN System cooling fan connector

3. CPU_FAN CPU cooling fan connector

4. DDR3_1~2 240-pin DDR3 SDRAM slots

5. ATX_POWER Standard 24-pin ATX power connector

6. SATA1~4 Serial ATA 3Gb/s connectors

7. F_PANEL Front panel switch/LED header

8. CLR_CMOS Clear CMOS jumper

9. F_USB1~2 Front panel USB 2.0 headers

10. USBPWR_F Front panel USB power select jumper

11. COM Serial port header

12. SPDIFO SPDIF out header

13. CASE Case open header

14. F_AUDIO Front panel audio header

15. SPK Speaker header

16. LDC Debug Card header

17. PCIE1 PCI Express x1 slots

18. PCIEX16 PCI Express slot for graphics interface

19. USBPWR_R Rear USB/PS2 power select jumper

20. ATX12V 4-pin +12V power connector

A55F2-M4USERMANUAL

,ĞĂĚĞƌWŝŶĞĮŶŝƟŽŶĂŶĚ:ƵŵƉĞƌ^ĞƫŶŐƐ

F_AUDIO

F_USB1~2

COM

KEY

PORT 1L

PORT 1R

PORT 2R

AUD_GND

PRESENCE# SENSE1_RETURN

KEY

SENSE2_RETURN

KEY

F_PANEL

Hard disk LED (-)

Hard disk LED (+)

Reset Switch (-)

Reset Switch (+)

Power Switch (-) Power Switch (+)

MSG LED (+)

MSG LED (-)

Ground

Power +5V

GroundUSB Port A (-)

USB Port B (-)

USB Port A (+)

USB Port B (+)

Serial Output

Data Carrier Detect

Serial Input

Ring Indicator

Data Terminal ReadyClear to Send

Request to Send

Data Set Ready

Ground

PORT 2L

LDC

Clock

KEY+3.3V

LPC Signal LPC Signal

LPC Signal

LPC Signal Ground

Reset

A55F2-M4USERMANUAL

IntruderGround

CASE

CLR_CMOS Jumper

1-2: NORMAL

Before clearing the CMOS, make sure to turn off the system.

CLR_CMOS

312

USBPWR_R (Rear USB PS/2 Power Select Jumper)

USBPWR_F (Front Panel USB Power Select Jumper)

VCC

(Default) 5VSB

VCC

(Default) 5VSB

2-3: CLEAR CMOS

+12V

SYS_FAN

Ground

SPDIFO

SPDIF OUT Ground

VCC KEY

CPU_FAN

Sensor

PWM

Ground

+12V

SPK

VCC Signal

KEY Ground

A55F2-M4USERMANUAL

I/O Ports

1. PS/2 Mouse (green)

Use the upper PS/2 port to connect a PS/2 mouse.

2. PS/2 Keyboard (purple)

Use the lower PS/2 port to connect a PS/2 keyboard.

3. VGA Port

Connect your monitor to the VGA port.

4. HDMI Port (Optional)

You can connect the display device to the HDMI port.

5. USB 2.0 Ports

Use the USB 2.0 ports to connect USB 2.0 devices.

6. LAN Port

Connect an RJ-45 cable to the LAN port to connect your computer to the Network.

7. Line-in (blue)

It can be connected to an external CD/DVD player, Tape player or other audio

devices for audio input.

8. Line-out (lime)

It is used to connect to speakers or headphones.

9. Microphone (pink)

It is used to connect to a microphone.

LAN LED Status Description

OFF No data

Orange blinking Active

OFF No link

Green Link

Activity LED

Link LED

LAN Port

English

Step 1. Ins of the CPU and CPU Cooler:

Hardware Guide

Ins Steps

Step 2. of Memory Modules:

2-1. Unfasten the latches on each side

of the DIMM slots.

Step 3. Ins of Motherboard:

3-1. Replace the back I/O plate of the

case with the I/O shield provided in

motherboard’s package.

2-2. Firmly press the DIMM down un l it

seats correctly. Make sure the slot

latches are levered upwards and latch

on the edge of the DIMM.

3-2. Place the motherboard within the

case by it into the I/O plate.

Secure the motherboard to the case

with screws.

Step 4. of an Expansion card:

Remove the metal located on the slot and then insert the expansion card into the

slot. Press the card Įrmly to make sure it is fully inserted into its slot. And then

return the screw back to its .

Locate the CPU cut edge (the corner with

insert the CPU correctly, then press the

1-2. Apply thermal grease on top of the

CPU. Put the CPU Fan down on the

module and Ňip the levers

over the heat sink in place.

English

Step 5. Connecting Cables and Power Connectors:

c. Connect 24-pin power cable

The ATX_12V 4-Pin power connector is used

to provide power to the CPU. When installing

4-pin power cable, the latch of power cable

matches the ATX_12V connector perfectly.

b. Connect SATA power connector to the

SATA device

Once the steps above have been completed, please connect the peripherals such

as the keyboard, mouse, monitor, etc. Then, connect the power and turn on the

system. Please install all the required software.

Step 6: Connecting ports on the case:

a. Connect the SATA hard drive to its

SATA cable

d. Connect 4-pin power cable

Please note that when installing 24-pin

power cable, the latches of power cable

and the ATX connector match perfectly.

The sequence of installation may differ depending on the type of case and

devices used.

Using BIOS

The BIOS (Basic Input and Output System) Setup Utility displays the system’s

configuration status and provides you options to set system parameters. When

you power on the system, BIOS enters the Power-On Self Test (POST) routines,

please press <DEL> or F2 to enter setup. When powering on for the first time, the

POST screen may show a “CMOS Settings Wrong” message. Please enter BIOS and

choose “Load Default Settings” to reset the default CMOS values. (Changes to

system hardware such as different CPU, memories, etc. may also trigger this

message.)

Inhaltsverzeichnis

Sprachen:

Andere ASROCK Hauptplatine Handbücher

ASROCK

ASROCK Z390 Phantom Gaming 9 Bedienungsanleitung

ASROCK

ASROCK X58 DELUXE3 - V1.0 Bedienungsanleitung

ASROCK

ASROCK Z77 Extreme9 Bedienungsanleitung

ASROCK

ASROCK H67M-HT Bedienungsanleitung

ASROCK

ASROCK H610M Bedienungsanleitung

ASROCK

ASROCK H61M-DG3/USB3 Bedienungsanleitung

ASROCK

ASROCK WOLFDALE1333-GLAN-M - V1.0 Bedienungsanleitung

ASROCK

ASROCK H61M-PS Bedienungsanleitung

ASROCK

ASROCK A88M-G/3.1 Bedienungsanleitung

ASROCK

ASROCK H67M Bedienungsanleitung

ASROCK

ASROCK IMB-140 Plus Bedienungsanleitung

ASROCK

ASROCK Z87EXTREME11/ac Bedienungsanleitung

ASROCK

ASROCK P43DE3L Bedienungsanleitung

ASROCK

ASROCK H310CM-HG4 Bedienungsanleitung

ASROCK

ASROCK AD510PV Bedienungsanleitung

ASROCK

ASROCK FM2A75 Pro4 Bedienungsanleitung

ASROCK

ASROCK 4X4-4800U Bedienungsanleitung

ASROCK

ASROCK Z87 OC Formula/ac Bedienungsanleitung

ASROCK

ASROCK J4125-ITX Bedienungsanleitung

ASROCK

ASROCK 880GMH USB3 R2.0 Bedienungsanleitung

ASROCK

ASROCK IMB-A182P Bedienungsanleitung

ASROCK

ASROCK FM2A85X Pro Bedienungsanleitung

ASROCK

ASROCK X399D8A-2T Bedienungsanleitung

ASROCK

ASROCK B560M Pro4/ac Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung