Assa Abloy Sargent PE8700 Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com

Installation Instructions

permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

PE8700 Series (Standard, 12-, HC-, & HC4-)

Surface Vertical Rod Exit Devices

A8307-1 5/23

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

Screw Chart

DESCRIPTION

TOTAL QTY

SUPPLIED

WHERE USED

#10-24 X 3/4" FLAT HEAD

MACHINE SCREW

STANDARD

FIRE RATED, HC

(4) CHASSIS

CORNER MOUNTING HOLES

(METAL DOOR)

(3) TOP CASE (STD.)

(METAL DOOR)

(3) BOTTOM CASE (STD.)

(METAL DOOR)

#10 X 1-1/4" FLAT HEAD

WOOD SCREW

STANDARD

FIRE RATED

(4) CHASSIS

CORNER MOUNTING HOLES

(WOOD DOOR)

(3) TOP CASE (STD.)

(WOOD DOOR)

(2) TOP CASE (FIRE RATED)

BOTTOM MOUNTING HOLES

(WOOD DOOR)

(3) BOTTOM CASE (STD.)

(WOOD DOOR)

(2) BOTTOM CASE (FIRE RATED)

TOP MOUNTING HOLES

(WOOD DOOR)

#10-24 X 3/4" ROUND HEAD

MACHINE SCREW

(2) REAR MOUNTING PLATE

(METAL DOOR)

#10 X 1-1/4" ROUND HEAD

WOOD SCREW

(2) REAR MOUNTING PLATE

(WOOD DOOR)

#12-24 X 3/4" ROUND HEAD

MACHINE SCREW

(2) TOP CASE (HC)

TOP MOUNTING HOLES

(2) BOTTOM CASE (HC)

BOTTOM MOUNTING HOLES

#12-24 X 3/4" FLAT HEAD

MACHINE SCREW

(2) TOP CASE (HC)

BOTTOM MOUNTING HOLES

(2) BOTTOM CASE (HC)

TOP MOUNTING HOLES

(4) 654 TOP LATCH STRIKE

#10-24 X 3/4" OVAL HEAD

MACHINE SCREW

(2) TOP CASE (FIRE RATED)

BOTTOM MOUNTING HOLES

(METAL DOOR)

(2) BOTTOM CASE (FIRE RATED)

TOP MOUNTING HOLES

(METAL DOOR)

(2) 648 TRANSOM STRIKE

#10-24 X 1-1/2" OVAL HEAD W/ GROMMET NUT

MACHINE SCREW

(2) TOP CASE (FIRE RATED)

TOP MOUNTING HOLES

#10-24 X 1-1/2" ROUND HEAD W/ GROMMET NUT

MACHINE SCREW

(2) BOTTOM CASE (FIRE RATED)

BOTTOM MOUNTING HOLES

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

DESCRIPTION

TOTAL QTY

SUPPLIED

WHERE USED

#12-24 X 1" FLAT HEAD

MACHINE SCREW

(2) 646 TOP STRIKE

(METAL FRAME)

#12 X 1-1/2" FLAT HEAD

WOOD SCREW

(2) 646 TOP STRIKE

(WOOD FRAME)

#10 X 1-1/4" OVAL HEAD

WOOD SCREW

(2) 648 TRANSOM STRIKE

(WOOD FRAME)

#10-24 X 3/4" FLAT HEAD

MACHINE SCREW WITH CAULKING ANCHOR

(2) 624 BOTTOM STRIKE

#12 X 1" FLAT HEAD

WOOD SCREW

(2) 624 BOTTOM STRIKE

(WOOD FRAME)

1/4"-20 X 2" FLAT HEAD

MACHINE SCREW W/ANCHOR

2 (3)

(3) 653 BOTTOM STRIKE

(2) 655 BOTTOM STRIKE

#10-24 X 1-1/2" OVAL HEAD

MACHINE SCREW

(2) TOP ROD GUIDE

(METAL DOOR)

(2) BOTTOM ROD GUIDE

(METAL DOOR)

#10 X 1-3/4" OVAL HEAD

WOOD SCREW

(2) TOP ROD GUIDE

(WOOD DOOR)

(2) BOTTOM ROD GUIDE

(WOOD DOOR)

#8-32 X 5/16" W/ #6 OVAL HEAD

MACHINE SCREW

(4) CHASSIS COVER

(2) END CAP

(4) TOP CASE COVER

(4) BOTTOM CASE COVER

1/4"-20 X 2-3/8" KNURLED FLAT HEAD

MACHINE SCREW

(2) EXIT TRIM

(IF USED)

Screw Chart

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

Rail Cutting Guide (Provided)

Support Block (Provided)

DOOR HANDS DETERMINED FROM OUTSIDE OF DOOR

OR SECURED SIDE

Tools Needed

All PE8700 series devices are

handed, except for the PE8710,

which is field reversible. The

PE8710 is shipped as LHR, unless

ordered as RHR

To Change Hand of PE8710

Exit Device:

Handing

1. Remove both chassis pins and main slide.

2. Remove lift lever pin and lift lever.

3. Rotate chassis 180° and reposition lift lever and lift lever pin as shown below

4. Position main slide with large end of main slide at the bottom and retain with chassis pins.

Lift lever pin

Chassis pin

Lift lever

Main slide

Large end

Chassis

Left Hand

Reverse

Right Hand

Reverse

Main Slide

Large end

Lift lever

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

16- Cylinder Lockdown

(Exploded View For Clarity)

Top cover

Top rod

Rod guide

Chassis

Top case

Bottom rod

Bottom

case

Slide mounting rail insert

with cylinder dogging

(16-prefix) into mounting

rail.

Standard PE8700 Exit Shown

"Lock Down Key"

To operate: Depress push rail; Insert

hex key, and turn counter clockwise.

Chassis Cover

End Cap

Mounting Plate

Push Rail Assembly

Rod

silencer

Bottom

Rod

silencer*

Bottom rod guide*

Bottom case cover*

*Not included with NB- option.

Product Overview

Before installation:

1. Install mullion, if used.

2. Fit and hang door.

3. Check the box’s label for the size of the exit device.

4. For wood doors, use wood screws & prep accordingly.

The surface of the door where the exit device is to be applied

must be flush. Clear away any raised projections to allow

exit device to rest on the flat surface of the door. If shim kit is

required, contact your distributor.

Note: Please refer to trim and other installation instructions

provided in the box.

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

• With door closed, tape template for chassis/

trim on inside of door, along vertical and

horizontal reference lines.

• Fold top case template and tape on inside of

door along vertical reference lines.

• With door closed, determine dimension “A”

to located vertical reference line.

• If door stile is 4-1/2” wide or wider, “A” is

2-3/4”. If door stile is less than 4-1/2”, “A” is

1/2 the exposed width of the door stile when

the door is closed against the door stop.

• Standard rail centerline height is 39-5/8”

above the finished floor.

• Horizontal reference line is 36-1/4” standard.

(Location of lower chassis mounting holes.)

36-1/4”

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

• Drill and tap all holes #10-24 from inside of

door, for chassis and top case.

• Mortise pockets for outside trim, if required.

See installation instructions supplied with trim

for details.

NOTE: Any holes drilled from the outside need

pilot holes drilled from the inside to ensure good

alignment.

NOTE: For electrical trim applications, ensure

access to a raceway from the trim to the electric

hinge or armored door loop.

• Drill and tap all strike mounting holes for

#12-24 in locations for applicable strike.

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

Install chassis mounting screws. DO NOT FULLY

TIGHTEN. See steps 5a and5b for trim mounting.

Position ET trim on door. Align spindle with

bell housing. Thru-bolt chassis to ET trim with

(2) 1/4-20 flat head screws.

55a

P700 NE & P700 WE Series ET Trim

Thumb Piece Trim

5/16"

STS TRIM

SHOWN

FLL TRIM

SHOWN

PE8762 OR PE8763

BY FLW SHOWN

NOTE: Thumb Trim is not available for HC-PE8700 Series Exit Devices.

Determining rim cylinder tail length.

For FLL, FLW, MAL, STS or PTB Trim:

1. Position trim on door (except STS).

2. Insert rim cylinder through trim plate (or cylinder collar

for STS trim).

3. Mark cylinder tail at 5/16” beyond inside door surface.

4. Remove cylinder and trim from door and cut tail piece

as marked.

Chassis

P700 Trim

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

NOTE: STS, FLL, FLW and MAL thru-bolt to chassis with (1) 1/4-20 flat head screw. PTB trim thru-bolts to

chassis with (2) 1/4-20 flat head screws. DO NOT FULLY TIGHTEN.

For PE8763 long end of pin

faces up. Cylinder turns

360° to the left or right.

For PE8762 long end of pin

faces down. Cylinder turns

180° in both directions.

Cylinder

hub Hub pin

down for

62 function

Chassis

Hub pin

up for

63 function

5b Thumb Piece Trim, Continued

1. Hold trim plate to door.

2. Insert cylinder and secure using supplied back plate.

3. Position cylinder hub within the chassis to correct position for desired function (see above).

4. Position chassis on door, align cylinder tail with hub and secure chassis to door with (4) #10 flat

head screws using the corner mounting holes. DO NOT FULLY TIGHTEN.

Mounting Trim

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8307-1 5/23

PE8700 Series (Standard, 12-, HC-, & HC4)

Installation Instructions

Surface Vertical Rod Exit Device

If the rail doesn’t need to be cut, continue to page 12, step 7.

If the rail must be cut, follow these steps on page 10 and 11:

Refer to the individual exit device installation instructions for rail cutting requirements / restrictions.

Instructions will vary based on device type and options.

Do not cut closer than 1-5/8” from

the the front edge of the rail insert.

• Determine cut off dimension “X” by subtracting 2-7/8”

from dimension “Y”. Mark cut off point on mounting rail.

(See below.)

Verticle reference line (C of chassis)

2-7/8”

min.

For doors with stile rail, the stile must overlap by 5/16” min.

A. Ensure there isn’t a gap between the

insert and the dogging slope, and the

carrier is flush with the mount.

B. Mark rail at the required cut length.

Insert

Dogging

slope

Cut line

Mount

Carrier

Information for Cutting Rails

Rail Sizes Door Widths

Max Min

E 32" 24"

F 36" 33"

J 42" 37"

G 48" 43"

Rail cutting guide

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türschloss Handbücher

Assa Abloy

Assa Abloy VERSO CLIQ V532 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Selector Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff 843ZY Bedienungsanleitung

Assa Abloy

Assa Abloy 81 C Series Bedienungsanleitung

Assa Abloy

Assa Abloy ANYKEY Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY EL654 Bedienungsanleitung

Assa Abloy

Assa Abloy PE920 Bedienungsanleitung

Assa Abloy

Assa Abloy Arrow Revolution U4A-YRHCPZW0 Technische Daten

Assa Abloy

Assa Abloy effeff ANYKEY Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Signature Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood CAVITY LOCK Bedienungsanleitung

Assa Abloy

Assa Abloy M32 Handbuch

Assa Abloy

Assa Abloy 1489 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Harmony Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8893 Bedienungsanleitung

Assa Abloy

Assa Abloy ZI IKON eCLIQ N109 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood Onyx 9A1A2/5PBLK Bedienungsanleitung

Assa Abloy

Assa Abloy OneSystem N1940 Bedienungsanleitung

Assa Abloy

Assa Abloy ESA500 Installationshandbuch

Assa Abloy

Assa Abloy EL580 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 8816 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED3400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT KP8977 Leitfaden

Assa Abloy

Assa Abloy LOCKWOOD 3782 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Baldwin

Baldwin 009 Series Bedienungsanleitung