Yale MORTISE 8800 SERIES Bedienungsanleitung

Installation Instructions

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

This product can expose you to

lead which is known to the state

of California to cause cancer and

birth defects or other reproductive

harm. For more information go to

www.P65warnings.ca.gov.

WARNING!

8800 Series Mortise Lock

Used with Sectional Trim and V Series Indicators

80-8800-0016-000 12/20

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8800 Series

Installation Instructions

Mortise Lock

80-8800-0016-000 12/20

1Tools Required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Indicator Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Lock Set Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Rehanding Indicator (if required). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Prepare Door for Mortise Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Install Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Prepare Door for Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Install Levers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Install Indicator Mounting Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Install Indicator Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Install Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Install Outside Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Perform Functional Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Indicator Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

TOC Table of Contents

1 Tools Required

#2 & #3 Phillips

head screwdrivers

Flat blade

screwdriver

1/8" Allen

Wrench 3/32" Drill bit T20 Torx Screw

with Tamper Pin

Driver

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Installation Instructions

8800 Series

Mortise Lock

80-8800-0016-000 12/20

2 Indicator Variants

4 Rehanding Indicator (If required)

Depending on function and option ordered,

indicators are provided in the following

variations, these instructions detail how to install

with cylinder, however other variations follow

similar instructions. (Figure 1)

Contact factory for any questions.

Figure 1 Cylinder - For

installation

on inside or

outside of door.

Thumbturn -

For installation

on inside of

door.

Coin Turn - For

installation

on outside of

door.

No input / blank -

For installation on

inside or outside

of door.

3 Lock Set Configuration

To re-hand lock, see instructions on lock body.

Left Hand

Hinges Left

Open Inward

Right Hand

Hinges Right

Open Inward

LHRB

Left Hand

Reverse Bevel

Hinges Left

Open Outward

RHRB

Right Hand

Reverse Bevel

Hinges Right

Open Outward

Figure 2

Verify hand and bevel of door. (Figure 2) Spindle Cam Position for Locks with Deadbolt

(*includes 8864 function)

Outside Indicator Inside Indicator

Door Hand LH/LHRB

Spindle Cam Position for Locks without Deadbolt

(*Does not include 8864 function)

Door Hand LH/LHRB

Figure 3

Note:

Stand on outside of locked door when determining door hand.

Next, verify inside and/or outside indicators are handed correctly,

using Spindle Cam Position chart. (Figure 3) If they are handed

correctly, skip to Step 5 “Prepare Door”.

If they are not handed correctly:

1. Remove retaining pad and spindle cam from assembly.

(Figure 4)

2. Position spindle cam in correct direction for door hand.

(Figure 3)

Important:

• For thumbturn indicators, make sure thumbturn is positioned

in the 12 o’clock direction as shown. (Figure 5)

3. Slide spindle cam post into correct slot of display slide.

(Figure 4)

4. Re-seat retaining pad into original position.

5. Return indicator to the vacant/unlocked position for

installation.

Thumbturn

Position

Figure 4

Figure 5

Retaining Pad

Spindle cam

Display

slide slot

Door Hand RH/RHRB

Inside Indicator Outside Indicator

Door Hand RH/RHRB

Outside Indicator Inside Indicator

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8800 Series

Installation Instructions

Mortise Lock

80-8800-0016-000 12/20

5 Installation

1Prepare Door for Mortise Lock

Prepare door for function holes, size, and location

according to 7088-0006 door marker template, if not

already prepped.

Figure 6

Inside of door Outside

of door

RH door

shown

Lock

Screws

2Install Lock

1. Verify strike location according to

template. Clean out door pocket and

door edge of debris.

2. Make sure handing of lock matches

handing of door. Slide lock into door.

(Figure 6)

3. Temporarily hand tighten two (2)

lock screws (#12 x 1-1/4" wood

screws, or #12-24 x1/2" machine

screws).

NOTE: Keep door open until installation is complete.

3Prepare Door for Indicator

Control

Hub

Guide

Template

Figure 7

Mark

holes

with

pencil

1. Insert template guide into control hub on

side where indicator will be used. (Figure 7)

2. Slide indicator template over template guide.

Important: Make sure the template is properly centered

and aligned to ensure smooth indicator operation.

3. Mark the four (4) hole positions indicated on tem-

plate.

4. Remove guide and template.

5. If indicators are being used on both sides of door,

repeat steps 3.1 through 3.4 for opposite side.

6. Remove lock body.

7. Drill four (4) marked holes with 3/32" diameter bit,

by 1/2" deep.

8. Reinstall lock body and hand tighten screws.

NOTE: If retrofitting over an existing product, ensure door

surface is free of chips and debris around holes so

indicator will sit flat against door surface.

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Installation Instructions

8800 Series

Mortise Lock

80-8800-0016-000 12/20

5 Installation, continued

4Install Levers

Figure 8

Figure 9

Figure 10

1. Insert outside mounting plate through

door and lock body, and hold. (Figure 8)

2. Align and fasten inside mounting plate

securely with two (2) #8-32 x 1-1/4"

screws.

3. Install roses on inside and outside

adapter plates.

5Install Indicator Mounting Plate

6Install Indicator Assembly

1. Screw indicator mounting plate to door with four

(4) #6 x 3/8" sheet metal screws. (Figure 9)

2. If indicators are being used on both sides of door,

repeat step 5.1 for opposite side.

1. Verify lock is in unlocked state (turn outside

lever to confirm).

2. Verify indicator is in vacant/unlocked position.

3. Assemble indicator assembly onto mounting

plate. (Figure 10)

4. Secure indicator assembly to door with two (2)

machine screws.

• Use #832 x 5/8" screw for top

• Use #832 x 3/8" screw for bottom

5. If indicators are being used on both sides of

door, repeat steps 6.1 through 6.3 for opposite

side.

NOTE: Torx security screws recommended.

Outside

of door

Inside of door

Inside of door Outside of door

Inside lever

Rose RH door

shown

Set Screw

#832 x 11/4"

Screws

Inside MountingPlate

Outside Mounting Plate

Mounting

Plate

#6 x 3/8" Screws

Indicator

Assembly

#832 x 5/8"

Screw

4. If included, press rose adapter into rose and

mounting plate assemblies.

5. Unscrew inside spindle 1/2 turn and align

ramp in the horizontal position.

6. Slide plastic bushing onto outside lever and

spindle and insert through the lockbody.

7. Slide plastic bushing onto inside lever and

attach to spindle. Then tighten inside lever

set screw.

Rose

Plastic Bushing

Rose Adapter Rose Adapter

Plastic Bushing

Outside Lever and Spindle

#832 x 3/8"

Screw

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

8800 Series

Installation Instructions

Mortise Lock

80-8800-0016-000 12/20

5 Installation, continued

7Install Cylinder

Figure 11

Figure 12

Figure 13

1. Thread cylinder into lock until flush with indicator

escutcheon surface. (Figure 11)

• Pull key slightly out of cylinder to help thread into

lock body.

2. Tighten cylinder clamp screw with #2 Phillips

screwdriver.

• Check operation and adjust if necessary.

Notes:

• Yale logo must be horizontal and on top. (See

Figure 12)

• If double cylinder function is used, repeat steps 7.1

and 7.2 for second cylinder.

• Interchangeable Core cylinders require a control

key to remove and install the core. This is not pro-

vided standard. It must be requested seperately.

Cylinder

Clamp

Screw

Key and cylinder must be rotated as shown.

8Install Outside Front

1. Tighten the two (2) lock screws completely:

(Figure 13)

2. Attach outside front with two (2) flat head screws

#8-32 x 1/4".

9Perform Functional Check

DO NOT FORCE if resistance is encountered during

functional check. Refer back to Rehanding Indicator (if

required) section to ensure correct handing. Rehand if

necessary.

1. Insert key into cylinder (if present) and rotate:

• Ensure there is no friction against lock case or any

other obstructions.

2. Check key retracts latch:

• Key should rotate freely.

3. Throw deadbolt (if present):

• Check key retracts both deadbolt and latch.

4. Test levers:

• Confirm latch and deadbolt (if installed) retract.

5. Verify indicator displays correct status when

locked and unlocked.

Correct Incorrect

Lock Screw

Outside

Front

#832

x 1/4"

Screws

Lock Screw

without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited

For technical support contact Yale®at 800.438.1951 x5033 or [email protected]

Installation Instructions

8800 Series

Mortise Lock

80-8800-0016-000 12/20

6 Indicator Parts List

Figure 14

#Description Part # Req.

Sectional Escutcheon - Cylinder 81-0472-4000 x finish 1

Sectional Escutcheon - Coin Turn 81-0471-4000 x finish

Sectional Escutcheon - Thumbturn 50-8800-0364 x finish

Sectional Escutcheon - No Input/Blank 81-0473-4000 x finish

2 Indicator Window 856F049 1

Indicator Display Assembly - Green Unlocked / Red Locked 82-5602-4000

Indicator Display Assembly - Green Vacant / Red Occupied 82-5603-4000

Indicator Display Assembly - Green Unlocked Icon / Red

Locked Icon

82-5604-4000

Indicator Display Assembly - White Unlocked / Red Locked 82-5605-4000

Indicator Display Assembly - White Vacant / Red Occupied 82-5606-4000

Indicator Display Assembly - White Unlocked Icon / Red

Locked Icon

82-5607-4000

Indicator Display Assembly - Green Ouvert / Red Fermé 82-5684-4000

Indicator Display Assembly - Green Libre / Red Occupée 82-5685-4000

4A Indicator Spindle Cam - Thumbturn 50-8800-9328

4B Indicator Spindle Cam - Cylinder/No Input / Blank 50-8800-7335*

4C Indicator Spindle Cam - Cylinder Overtravel 50-8800-0378*

4D Indicator Spindle Cam - Thumbturn Overtravel 50-8800-0346

4E Indicator Spindle Cam - Coin Turn 50-8800-7339*

5 Indicator Retaining Pad 81-0749-9000 1

6 Sectional Indicator Screw Pack 85F497 FIN* 1

7 Sectional Indicator Mounting Plate 855F658 1

8 Sectional Indicator Template Kit (not shown) 50-8800-9343 1

*These parts are for 1-3/4" standard thickness doors. For other thicknesses, contact the factory.

NOTE: Reference 8800 Series parts manual for all lock body parts.

80-8800-0016-000 12/20

THE YALE BRAND, with its unparalleled global reach and

range of products, reassures more people in more countries

than any other consumer locking solution.

THE ASSA ABLOY GROUP is the world´s leading

manufacturer and supplier of locking solutions, dedicated to

satisfying end-user needs for security, safety and convenience.

Yale Commercial is a business associated with ASSA ABLOY Access and Egress

Reproduction in whole or in part without the express written permission of

ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited. Patent

pending and/or patent www.assaabloydss.com/patents.

U.S.A.

Yale Locks & Hardware

Address: 225 Episcopal Road

Berlin, CT 060374004

Tel: 18004381951

Fax: 18003380965

yalecommercial.com

Canada:

ASSA ABLOY Door Security Solutions Canada

Address: 160 Four Valley Drive

Vaughan, Ontario L4K 4T9

Tel: 18004613007

Fax: 18004618989

assaabloydss.ca

International:

ASSA ABLOY Americas International

Tel: 19058217775

Fax: 19058211429

assaabloyai.com

Customer Service Phone:

1-800-438-1951

Customer Service Fax:

1-800-338-0965

Technical Product Support:

techsupport.yale@assaabloy.com

Customer Service:

customerservice.yale@assaabloy.com

Website:

Yalecommercial.com

Email for orders:

orders.yaleus@assaabloy.com

Trusted every day

Part of ASSA ABLOY

Andere Handbücher für MORTISE 8800 SERIES

Inhaltsverzeichnis

Andere Yale Türschloss Handbücher

Yale

Yale nexTouch Technische Daten

Yale

Yale YDD120 Bedienungsanleitung

Yale

Yale YDM 3111 Bedienungsanleitung

Yale

Yale Assure Lock YRC256 Technische Daten

Yale

Yale YRD210 Technische Daten

Yale

Yale Assure Lock 2 Touch Bedienungsanleitung

Yale

Yale Keyfree Bedienungsanleitung

Yale

Yale 680F Bedienungsanleitung

Yale

Yale YDM2107 Bedienungsanleitung

Yale

Yale GATEMAN YDM 3109 Bedienungsanleitung

Yale

Yale Code Handle 8830 Handbuch

Yale

Yale Conexis L1 Bedienungsanleitung

Yale

Yale 2310BC Series Bedienungsanleitung

Yale

Yale AYRD110 Technische Daten

Yale

Yale YDM4109 Bedienungsanleitung

Yale

Yale Real Living YRD210-ZB Technische Daten

Yale

Yale eBOSS E5400LN Series Bedienungsanleitung

Yale

Yale YDR2105 Bedienungsanleitung

Yale

Yale Real Living YRD156 Technische Daten

Yale

Yale YDM4109 Bedienungsanleitung

Yale

Yale EC800 Bedienungsanleitung

Yale

Yale Conexis L1 Bedienungsanleitung

Yale

Yale Keyless Connected Bedienungsanleitung

Yale

Yale Helios S Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung

Saflok

Saflok Quantum ädesē RFID Bedienungsanleitung

ArrowVision

ArrowVision Shepherd 210 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 10X Line Bedienungsanleitung