ASTi ACE Target Leitfaden

Advanced Simulation Technology inc.

500A Huntmar Park Drive

Herndon, Virginia 20170 USA

Tel. (703) 471-2104 • Fax. (703) 471-2108

www.asti-usa.com

Advanced Simulation Technology inc.

500A Huntmar Park Drive, Herndon, Virginia 20170 USA

Revision B, Version 0 (March, 2018)

ACE Target and Studio Cold Start Guide

Document: DOC-TEL-ACE-CS-B-0

Product Name: ACE Target and ACEStudio

ACE Target and Studio Cold Start Guide

Restricted Rights: Use, duplication, or disclosure by the Government is subject to restrictions as

set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software

clause at DFARS 252.227-7013.

This material may be reproduced by or for the U.S. Government pursuant to the copyright

license under the clause at DFARS 252.227-7013 (1994).

ASTi

500A Huntmar Park Drive

Herndon, Virginia 20170 USA

iii

Revision history

Date Revision Version Comments

8/8/2016 A 1 Completes internal reorganization and makes minor edits for gram-

mar, consistency, and style; moves "(Optional) Perform a media

check" after "Configure the BIOSsettings."

9/26/2017 A 2 Changes internal inline styles to character styles; adds bookmarks

to section titles; makes edits to the wording in Section 6.0, "ACE

Target cold start procedure" on page17.

10/3/2017 A 3 Makes minor edits to wording and fixes conditions display error.

2/28/2018 A 4 Adds missing "BIOS Advantech AIMB-562 American Megatrends"

section back to BIOS configuration instructions.

3/13/2018 B 0 Adds instructions for the Red Hat 7 cold start procedure.

Contents

1.0 Introduction 1

2.0 Required equipment 2

3.0 Back up the Telestra server 3

4.0 Configure the BIOSsettings 5

4.1 BIOS Advantech AIMB-562 American Megatrends 6

4.2 BIOS Advantech AIMB-562 Award 7

4.3 BIOS Q35AX American Megatrends 8

4.4 BIOS Q67AX 2.14.1219 and higher 9

4.5 BIOS Q67AX 2.02.1205 and lower 11

4.6 BIOS BLH6710H 12

4.7 BIOS JGIBX10J 13

5.0 (Optional) Perform a media check 15

6.0 ACE Target cold start procedure 17

6.1 ACE Target cold start for Red Hat 5.X 17

6.1.1 Install Red Hat 5.10 and higher 17

6.1.2 Install ACE Target versions 4.13 and higher 19

6.2 ACE Target cold start for Red Hat 6.X 20

6.3 ACE Target cold start procedure for Red Hat 7.X 21

7.0 Install terrain server software 22

8.0 Target iSCSI cold start procedure 23

8.1 Install iSCSI boot firmware 23

8.2 Configure iSCSI boot firmware 24

8.3 iSCSI cold start procedure for Red Hat 5.X 24

8.3.1 Install Red Hat 5.X on an iSCSI Target 25

8.3.2 Install ACE software version 4.X for iSCSI 26

8.4 iSCSI cold start procedure for Red Hat 6.X 27

9.0 Configure the Telestra Target network 33

10.0 ACEStudio cold start procedure 35

10.1 ACEStudio cold start procedure for Red Hat 5.X 35

10.1.1 Install Red Hat 5.10 and higher 35

10.1.2 Install ACEStudio 4.5 and higher 37

10.1.3 ACEStudio 4.X development workstation setup 39

10.2 ACEStudio cold start procedure for Red Hat 6.X 41

10.2.1 Install ACEStudio versions 6.0 and higher 41

10.2.2 Set up ACEStudio 6.X development workstation 42

10.3 ACEStudio cold start procedure for Red Hat 7.X 45

11.0 Restore system backup 46

12.0 Options files 47

12.1 Upload Options files to the RMS 48

Appendix A: Memory Test procedures 49

A-1 Memory Test (ACE software version 6.X) 49

A-2 Memory Test (ACE software versions 4.31 and higher) 49

A-3 Memory Test (ACE software versions 4.10–4.30) 50

Appendix B: Install older software versions 51

B-1 Install Red Hat 5.1–5.9 51

B-2 Install ACEsoftware versions 4.5–4.12 51

B-3 Install ACE Target versions 4.1–4.4 52

B-4 Install ACEStudio versions 4.1–4.4 54

1.0 Introduction

The ACE Target and Studio Cold Start Guide (DOC-TEL-ACE-CS-B-0) supplants the pre-

viously separate ACE Target Cold Start Guide (DOC-02-TEL4-TCS-1) and ACE Studio Cold

Start Guide (DOC-02-TEL4-ASCS-1).

The cold start procedure(s) described in this document allow you to build Telestra systems from

scratch. There are three main reasons for using the cold start procedure:

lInstalling the latest software version

lRebuilding a damaged hard disk

lCreating spare hard disks

The following steps outline the cold start procedure:

1. To back up the Telestra server, see Section 3.0, "Back up the Telestra server" on page3.

2. To configure the BIOS settings, ensuring the cold start procedure runs properly, see Sec-

tion 4.0, "Configure the BIOSsettings" on page5.

3. (Optional) To perform a media check, see Section 5.0, "(Optional) Perform a media

check" on page15.

4. To complete the cold start procedure, erase the hard drive, and install the Red Hat and

Telestra Target software. For Red Hat 5 installation instructions, see Section 6.1.1,

"Install Red Hat 5.10 and higher" on page17. For Red Hat 6 installation instructions, see

Section 6.2, "ACE Target cold start for Red Hat 6.X" on page20.

5. Configure the network. First, assign a temporary IP address to the Telestra Target, which

allows a web browser to remotely access ACE Target software. Then use the Remote

Management System on a web browser to complete the network setup. To configure the

network, see Section 9.0, "Configure the Telestra Target network" on page33.

6. (Optional) If you purchased ACEStudio software, complete the ACEStudio cold start

procedure on a separate box. To install Red Hat 6 on an ACEStudio development work-

station, see Section 10.2, "ACEStudio cold start procedure for Red Hat 6.X" on page41.

7. To restore the Telestra server, see Section 11.0, "Restore system backup" on page46.

8. Upload the Options file. If the Options file is not included in the system backup file, you

must upload it manually. This step enables the software license for system functionality.

For Options file details and upload instructions, see Section 12.0, "Options files" on

page47.

ACE Target and Studio Cold Start Guide (Rev. B, Ver. 0)

2.0 Required equipment

Note: To install ACEStudio on a virtual machine, see the ACE Studio VM Quick Start

Guide.

To complete the ACE cold start procedure, you will need the following items:

lHardware

oTelestra 2U platform with removable hard drive

oMonitor

oKeyboard

lSoftware

oTelestra Target Software Installation DVD and/or Telestra Studio Software Installation

DVD

oRed Hat 5 Installation DVD or Red Hat 6 Installation DVD

The following shows the Telestra 2U rear panel:

Figure 1: Telestra 2U rear panel

Note: The chassis and connections shown here are for general representation only; the loc-

ation(s) of cards, ports, and slots may vary. For specific designations, consult the included

engineering drawings and labels on the rear of your chassis.

ACE Target and Studio Cold Start Guide (Rev. B, Ver. 0)

3.0 Back up the Telestra server

The Backup System Configuration page creates an archive of backup files on the devel-

opment workstation. This page includes the following settings:

lOptions: includes all options files loaded on the system.

lProjectsArchive: includes all projects archived on the system.

lRMSUsersAndConfig: includes user information (e.g., passwords, lockout settings).

lSoundLibrary: the library of sound files on the system, including the project's index and

files in Waveform (.wav) audio file format.

lTelestraConfig: includes configuration settings (e.g., network settings, preferences).

To create a system backup, follow these steps:

1. Open a web browser on the ACEStudio development workstation. Ensure the devel-

opment workstation shares the same network as the Telestra server.

2. To access the RMS, in the address bar, type the Telestra server's IP address.

3. In the top-right corner, click Login.

4. Log into the system using the following default credentials:

Username Password

admin astirules

5. From the left menu, under Configuration, click Backup Restore.

6. On the System Backup/Restore page, click Backup System Configuration.

Figure 2: Backup System Configuration

ACE Target and Studio Cold Start Guide (Rev. B, Ver. 0)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ASTi Desktop Handbücher

ASTi

ASTi Telestra 4 Installationsanleitung

Beliebte Desktop Handbücher anderer Marken

HP m9060n - Pavilion - Elite Technisches Datenblatt

Asus

Asus E210 Series Bedienungsanleitung

Dell

Dell Inspiron 600m Bedienungsanleitung

Dell

Dell Inspiron 3662 Bedienungsanleitung

TotalFlow

TotalFlow uFLO Bedienungsanleitung

HP Presario SV7000 - Desktop PC Bedienungsanleitung

HP ProDesk 400 G5 Handbuch

Logitech

Logitech MK320 Bedienungsanleitung

Dell

Dell XPS 730 H2C Bedienungsanleitung

Sony

Sony Vaio Series Bedienungsanleitung

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Bedienungsanleitung

Alto

Alto MD 250 Bedienungsanleitung

Lenovo

Lenovo ThinkCentre Edge 72 Handbuch

Lenovo

Lenovo ThinkStation D20 Handbuch

Arbor Technology

Arbor Technology FPC-7800 Series Bedienungsanleitung

Sony

Sony VAIO VGX-TP1 Series Bedienungsanleitung

Asus

Asus Eee Box B204 Bedienungsanleitung

Dell

Dell Optiplex 9010 All In One Bedienungsanleitung