Astra 3000 Series Bedienungsanleitung

INSTALLING YOUR DOOR CLOSER USING FITTING JIG AST9003 (No Supplied)

Retaining Plate

DOOR

FRAME

DOOR

Locking nut

Turn anti-clockwise to

decrease snap action or

clockwise to increase

snap action

Threaded

Rod

3000 SERIES

INSTALLATION INSTRUCTIONS

ADJUSTING THE DOOR CLOSING SPEED

Once installed, the closing speed may be adjusted.

A closing speed adjustment pin is located inside the body of the closer, above or below the fixing link.

The closing speed can be altered by opening the door to 90˚ and turning the adjuster pin with a

small flat screwdriver clockwise to decrease speed or anticlockwise to increase speed. When

adjusting the closing speed, please be aware that very slow settings may effect the performance of

the closer. It is recommended not to set a closing speed of less than 6 seconds.

For Declaration of Performance see www.astradoorcontrols.com

ADJUSTING THE SNAP ACTION

Prior to installation

The closer latching is factory set to give 5° of snap action.

Remove the small locking nut on the threaded rod at the

end of the body.

Using a small flat screwdriver turn the threaded rod

anti-clockwise to decrease or clockwise to increase the

‘snap action’.

After adjustment always replace the locking nut prior to

installing the closer in the door.

Offer up the fitting jig to

the door leaf with the lip

on the knuckle side of the

door just below or above

the middle hinge. The

centre line should always

be 22mm from the

knuckle side of the door.

Remove the retaining

plate. Ensure that it is

kept in a safe place in

case it is necessary to

remove the closer from

the door at any time.

Installing the closer the

wrong way will result in

failure and is not covered by

any warranty or guarantee.

Note: The ‘Astra England’

stamp may be upside down,

depending on the handing

of the door.

Fix the plate onto the

door frame making sure

it is exactly in line with

the other plate.

Insert the body of the

closer into the door leaf,

with the retaining plate

facing you, and screw fix.

Cut out the area required

to house the fixing plates

on both the door leaf and

the door frame.

Drill out a centre hole

15mm diameter to a

depth of 10mm.

Mark the top and bottom

edges level and square

across to the door frame.

Mark a centre line 22mm

from the knuckle side of

the frame.

Drill the hole for the

closer body using the

auger bit. Do not drill to

excess, the door control

should be a snug fit.

Fix using 4 screws.

Cert No 5893

ISO 9001

PL8006 install instru tions (2017 revision7).qxp_Safe T Closer instru ts 20/04/2017 14:21 Page 1

• After fitting the door closer these instructions and the retaining plate should be

kept in a safe place and referred to before any work on the door is carried out.

It is dangerous to remove the closer plate screws without first placing the

retaining plate in position.

• ou are advised to use an approved installer when fitting or removing this

product. It is potentially dangerous to remove or tamper with this product.

• Poor ventilation and limited air flow may, like other closers, affect the

performance of this closer. A suitable latching device may help door latching,

but we accept no liability for the performance of the closer in these

circumstances.

• It is important that the door hinges and associated fittings are correctly

installed and do not affect the ability of the closer to close and latch the door.

• All doors must be fitted with a pair and a half of fire tested EN1935

approved hinges.

• The door closer is designed to open to a maximum of 105° when installed

with the centre line of the plate 22mm from the hinge edge of the door.

When installing the closer in a thicker door the centre line of the plate must

remain at 22mm from the hinge edge to allow for 105° opening.

• Do not fit in conjunction with rising butts or parliament hinges. Hinges with any

projection greater than 10mm will result in a reduced angle of opening

• The screws supplied are not necessarily the appropriate screws for the

installation. It is the installers’ responsibility to ensure correct fixing is applied.

Piloting holes too large for the screws could result in the door closer pulling

out of the door and the frame.

• It is essential that fixing plate centres are exactly in line with each other when

the door is closed and each plate is recessed flush into the door and frame.

The gap between the fixing plates when the door is closed should be no

greater than 5mm and no less than 3mm.

• Please refer to the website www.astradoorcontrols.com for installation video

and advice. Fitting jigs and auger bits are available from approved stockists

and Astra Door Controls Ltd.

Astra Door Controls Ltd, Preston PR2 5AP, England www.astradoorcontrols.com

IMPORTANT PLEASE READ THESE NOTES BEFORE INSTALLATION

3000 SERIES

INSTALLATION INSTRUCTIONS Cert No 5893

ISO 9001

PL8006 install instru tions (2017 revision7).qxp_Safe T Closer instru ts 20/04/2017 14:21 Page 2

Andere Astra Türöffnungssystem Handbücher

Astra

Astra 3000 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung