Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Installation Instructions based on Application and Arm type

Standard Mounting Application -

H arm

For Standard Application - the Door Closer is mounted

on the hinge side of door (see page 2)

Parallel Arm Application -

PH9 Arm

For Parallel Arm Application - the Door Closer is mounted

on the stop side of door (see page 4)

Top Jamb Application -

H, HZ & HZA Arm

For Top Jamb Application - the Door Closer is mounted on the

frame on the stop side of the door (see page 6)

LEFT

HAND DOOR

RIGHT

HAND DOOR

HINGE SIDE HINGE SIDE

STOP SIDESTOP SIDE

INSTRUCTIONS FOR

1431 Door Closer with Hold Open Arms

1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6

FOR INSTALLATION ASSISTANCE CALL SARGENT AT 1-800-727-5477 / www.sargentlock.com

of Sargent Manufacturing Company is prohibited.

A7140F 1

IMPORTANT NOTICE

PRE-DRILL 3/32” HOLES FOR SELF-TAPPING SCREWS

OR TAP #12-24 FOR MACHINE SCREWS

A1) Select closer mounting position based on the maximum door opening, as listed below

Note: For ADA applications, select the 160ϒposition

MAIN

ARM

INDEX MARK

ON SPINDLE

RIGHT HAND DOOR

POSITION OF

MAIN ARM WHEN

ASSEMBLING

TO SPINDLE

B1) Prep door and frame

Note: 3/32" pilot holes are required when Self Tapping Screws are being used

Note: If machine screws are being used, use a drill #16 (.177) and a #12-24 tap

B2) Install closer body onto the door

B3) Install Foot & Rod Assembly onto the frames

C1) Install main arm on the closer with the index mark on the spindle aligning with the # 2 on the main arm (as shown)

**If Butt, Frame and Wall Conditions Permit

Door Will Open 180ϒ

MAXIMUM DOOR

OPENING

120ϒ7 1/2" 13 1/4"

160ϒ** 4 1/4" 10"

DIM. A DIM. B

C OF HINGE PIVOT

#12 X 1 1/2 SCREWS OR

#12-24 X 5/8 FLAT HEAD

MACHINE SCREW*

TOP OF DOOR

DOOR CLOSER

DIM. “B”

DIM. “A”

⁄

2-1/2"

⁄

*SEE PAGE 8 FOR MORTISE NUTS

RIGHT HAND DOOR ILLUSTRATED. SAME DIMENSIONS APPLY FOR LEFT HAND DOOR.

⁄

" MIN

TOPRAIL

FRAME

DOOR

FACE OF DOOR

RAILS TO 1

⁄

" MAY BE

USED PROVIDED FRAME

DOES NOT PROJECT

BEYOND FACE OF DOOR

⁄

STANDARD APPLICATION

DAttach hold open foot to frame with adjusting nut facing down for left hand door or up for right hand door, as illustrated below

FRAME FRAME

NUT FACES DOWN

NUT FACES UP

LEFT HAND

DOOR SHOWN

RIGHT HAND

DOOR SHOWN

of Sargent Manufacturing Company is prohibited.

A7140F

ACCESSORIES INFORMATION

1431-W corner bracket closer is mounted on bracket which is attached to door jamb

on stop side of door

Use this application for exterior doors to keep the closer inside of building; Also may be

used to obtain full 180ϒdoor opening

MORTISE NUTS FOR BOLTING THRU THE DOOR ARE FURNISHED WHEN ORDERED

STANDARD APPLICATION

E1) Opening the door slightly, slide rod into swivel arm and then close the door

E2) With the door closed, position the swivel arm so that it is 90º to the door surface

E3) Tighten the arm screw securely

Adjust closer as required (See page 8 for details).

MAIN

ARM

INDEX MARK

ON SPINDLE

1430-J COVER PLATE

MAY BE USED WHEN CLOSER IS MOUNTED

ON A NARROW RAIL TO IMPROVE APPEARANCE

WHEN CLOSER IS VIEWED THRU GLASS

H8 MORTISE FOOT

FOR USE WHERE THE

STANDARD SURFACE

APPLIED FOOT CANNOT

BE ATTACHED TO THE

TOP CASING OR WHERE

APPEARANCE IS A

MAJOR FACTOR

RIGHT HAND DOOR

ROD

90ϒ

ARM

SCREW

POSITION OF MAIN

ARM WHEN ASSEMBLING

TO SPINDLE

HOLD

OPEN ARM

of Sargent Manufacturing Company is prohibited.

A7140F 3

MAXIMUM DOOR

OPENING

of Sargent Manufacturing Company is prohibited.

A7140F

INSTRUCTIONS FOR INSTALLING PARALLEL ARM APPLICATION

CLOSER MOUNTED ON

STOP SIDE OF DOOR

ACCESSORIES INFORMATION

CLOSER IS MOUNTED ON PLATE WHEN

TOP RAIL IS TOO NARROW

1430-D DROP BRACKET

2 1/2" MIN.

DD1) Install main arm on the closer with the index mark on

spindle aligned with the number on the arm

Note: Left Hand Doors -align index mark with the # 4

on the main arm (as shown)

Note: Right Hand Doors -align index mark with the # 5

on the main arm (as shown)

D2) This requires the spindle to be rotated

D3) Rotate the spindle on the bottom of the closer to align

index mark with the required number on the arm

E1) Opening the door slightly, slide rod into swivel arm and

then close the door.

E2) With the door in the closed position, swivel the arm so that

the pivot is an 1-1/2" off the door surface (as shown below)

E3) Tighten the arm screw securely

INDEX MARK

ON SPINDLE

INDEX MARK

ON SPINDLE

MAIN

ARM

45°45°

MAIN

ARM

Adjust closer as required. See page 8 for details.

Left Hand Door Right Hand Door

NUT FACES DOWN

NUT FACES UP

RIGHT HAND

DOOR SHOWN

LEFT HAND

DOOR SHOWN

Select degree of door opening required and attach door closer body to door (long end toward hinge) and foot bracket to frame (according to

illustration on “A” page 3). Use templates enclosed for special arms.

Mount hold open arm to bracket with adjusting screw facing down for left hand door, facing up for right hand door.

LEFT HAND DOOR

PRELOAD 45°

ARM

SCREW

ROD

FOOT BRACKET

HOLD

OPEN ARM

1430-J COVER PLATE

May be used when closer is mounted on

a narrow rail to improve appearance when

closer is viewed through glass

#8 MORTISE FOOT

For use where the

standard surface applied

foot cannot be attached

to the top casing or where

appearance is a major

factor

#H8 MORTISE FOOT

MORTISE NUTS FOR BOLTING THRU THE DOOR

ARE FURNISHED WHEN ORDERED

LEFT HAND DOOR

PRELOAD 45°

ARM

SCREW

ROD

FOOT BRACKET

HOLD

OPEN ARM

1-1/2"

of Sargent Manufacturing Company is prohibited.

A7140F 5

of Sargent Manufacturing Company is prohibited.

A7140F

LEFT HAND DOOR ILLUSTRATED

SAME DIMENSIONS APPLY FOR RIGHT HAND

DOOR MEASURE FROM HINGE C

INSTALLATION

INSTRUCTIONS CLOSER MOUNTED ON FRAME

ABOVE STOP SIDE OF A DOOR

TOP JAM APPLICATION

#2 x 1-1/2" WOOD SCREWS

OR #12-24 x 5/8" FLAT

HEAD MACHINE SCREWS

TOP OF DOOR

2-1/4"

DOOR CLOSER

5/8"

11-1/8"

CLOSER FOOT

APPLIED TO

DOOR

3-3/8"

COF HINGE PIVOT

DIM "A"

2-1/2"

2-9/16"

DEPTH OF REVEAL

COF CLOSER

MOUNTING

SCREWS

DOOR

SPRING POWER

ADJUSTING NUT

DECREASE

POWER

INCREASE

POWER

–+

FOR EXTERIOR DOORS AND WHERE STRONG DRAFT EXISTS INCREASE SPRING POWER AS NEEDED BY TURNING SPRING

ADJUSTING NUT CLOCKWISE. IF NECESSARY, DECREASE SPRING POWER TO MEET REQUIREMENTS BY TURNING SPRING

ADJUSTING NUT COUNTER CLOCKWISE.

* FOR EXTERIOR DOORS USE 1430 CLOSERS ONLY.

** CLOSERS ARE FACTORY SET FOR INTERIOR DOORS.

CW-CLOCKWISE CCW-COUNTER CLOCKWISE

SPRING ADJUSTMENT

ADJUST SPRING POWER ACCORDING TO CHART.

NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT*

USE CHART AS GUIDE ONLY.

FACTORY**

SET

4-7 CW

7-10 CW

DOOR

WIDTH

(INCHES)

APPROXIMATE

DOOR WEIGHT

(POUNDS)

1430 DOOR

CLOSERS

OVER 48

110

115

130

150

155

165

170

180

1-3 CCW

FACTORY**

SET

1-3 CW

4-7 CW

7-10 CW

1431*

DOOR

CLOSERS

HINGE SIDE HINGE SIDE

STOP SIDE STOP SIDE

THIS IS A LEFT HAND DOOR THIS IS A RIGHT HAND DOOR

CLOSERS ARE NON-HANDED

ARM ASSEMBLY

TYPE

REVEAL DEPTH DIM. A MAX DOOR

OPENING

RANGE OF HOLD

OPEN

“H” ARM 0" TO 2" 5-3/4" 180° 80° - 180°

“HZ” ARM 2-1/8" TO 5" 6-1/2" 140° 80° - 140°

“HZA” ARM 5-1/8" TO 8" 7-1/4" 140° 80° - 130°

of Sargent Manufacturing Company is prohibited.

A7140F 7

INSTRUCTIONS FOR INSTALLING TOP JAMB

CLOSER MOUNTED ON FRAME

ABOVE STOP SIDE OF DOOR

DD1) Install main arm on the closer with the index mark on spindle aligned with the number on the arm

Note: Left Hand Doors -align index mark with the # 3 on the main arm (as shown)

Note: Right Hand Doors -align index mark with the # 1 on the main arm (as shown)

F1) Opening the door slightly, slide rod into swivel

arm and then close the door

F2) With the door closed, position the main arm so

it is at 90º to the door surface

F3) Tighten the arm screw securely

Adjust closer as required. See page 8 for details.

INDEX MARK

ON SPINDLE

INDEX MARK

ON SPINDLE

MAIN

ARM

45°

MAIN

ARM

LEFT HAND DOOR

POSITION

OF MAIN ARM

WHEN

ASSEMBLING

TO SPINDLE

FRAME FRAME

NUT FACES DOWN

NUT FACES UP

LEFT HAND

DOOR SHOWN

RIGHT HAND

DOOR SHOWN

Attach hold open foot to frame with adjusting nut facing down for left hand door or up for right hand door as illustrated below.

POSITION OF

MAIN ARM WHEN

ASSEMBLING

TO SPINDLE

ROD

HOLD

OPEN ARM

ARM

SCREW

LEFT HAND DOOR

RIGHT

ANGLE

RIGHT HAND

LEFT HAND

INSTALL COVER AS FOLLOWS:

FOR STANDARD AND PARALLEL ARM APPLICATION

•Screw short cover screw (#8-32 X 5/16) into top of case

approximately 2 turns

•Assemble plastic support and long cover screw (#8-32 X 1 1/4)

into bottom of case approximately 2 turns

•Hold support against case (approximately 2 turns)

between flange and screw head

•Position cover on closer and tighten screws

FOR TOP JAMB APPLICATION

•Assemble plastic support and long cover screw (#8-32 X11/4")

into top of case approximately 2 turns

•Screw short cover screw (#8-32 X 5/16") into bottom of case

approximately 2 turns

•Slide cover into gap between flange and screw head. Position cover

on closer and tighten screws

GAP

SHORT COVER SCREW

PLASTIC SUPPORT AND

LONG COVER SCREW

INSERT IS REMOVABLE.

PLACE IN UNUSED OPENING

SHORT COVER SCREW

PLASTIC SUPPORT AND

LONG COVER SCREW

INSERT IS REMOVABLE. PLACE IN UNUSED OPENING

RIGHTHAND

ILLUSTRATED

FINAL ADJUSTMENT AND REGULATING PROCEDURE

FRAME

UNREINFORCED

DOOR

COVER

DOOR

STOP

MORTISE

NUTHEAD

DRILL

3/8" DIA.

HOLE FOR

MORTISE

NUTBODY

DRILL 1/4" DIA.

HOLE FOR MOUNTINGSCREWS

1. For top jamb and corner bracket

applications: The door closer foot

will be attached to the door in a

manner similar to that shown for

mounting the closer body.

2. The appropriate mortise nuts

and screws will be suppled based

on door thickness.

Door construction must provide a

bridge type reinforcement to prevent

the door rail from collapsing when

through-bolts are tightened.

Adjustment hold open arm

Slight tightening or loosening of hold

open nut changes holding position of door.

Note: To protect wall, trim and closer, use a door stop

located 10°beyond hold open position but not beyond

the max. door opening shown on instructions.

HOLD

OPEN

NUT

USE 15/16"

WRENCH TO

ADJUST NUT

Minimum recommended door closing time is 6 Seconds for

doors opened to 90 degrees.

Use 1/8” hex (Allen) wrench to adjust valves as needed.

Closing and latching speeds:

Turn valves clockwise to slow down or counterclockwise to

speed up door movement.

Backcheck:

To regulate the intensity of back check action, turn valve clockwise

to increase or counterclockwise to decrease checking.

CAUTION: Set valve for slight cushioning effect; closer can be

damaged if the checking action is too abrupt. Never use

the backcheck as a door stop. Always use a door stop to stop

the door.

Delayed action feature (Optional feature on some models):

“Delayed action” provides slow door closing through the

delayed action range. Turn valve clockwise to slow down or

counterclockwise to speed up door movement.

of Sargent Manufacturing Company is prohibited.

A7140F

DOOR WIDTH 1431 DOOR CLOSER

(INCHES)

24-30 TURN nut 1-3

30-36 FACTORY SET

36-42 TURN nut 1-4

42-48 TURN nut 7-9

NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT

Adjusting door

to close due to

high draft

conditions may

exceed ADA

standards.

Consult local

ordinances

when fire doors

are involved

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FT Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron EEB3N Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood 724 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy effeff ePED 1386Z1LB7 04S0 Series Referenzhandbuch

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy Norton Narrow Profile Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-C Bedienungsanleitung

Assa Abloy

Assa Abloy Crawford MCS-R Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W73ER Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5200 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy UNION DoorSense 8755A Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7100SZ Series Kurzanleitung

Assa Abloy

Assa Abloy G-CO-CS Bedienungsanleitung

Assa Abloy

Assa Abloy RD150-3 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR7500 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung