Asus P4T-M Technisches Datenblatt
ASUS P4T-M Quick Setup Manual 1
®
P4T-M
Intel®850 ATX Motherboard
Quick Setup Manual
SPECIFICATIONSAND INFORMATION CONTAINED IN THIS MANUALARE FURNISHED
FORINFORMATIONALUSE ONLY,ANDARESUBJECTTOCHANGEATANYTIME WITH-
OUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BYASUSTeK
COMPUTER INC. (ASUS). ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR
ANY ERRORS OR INACCURACIES THAT MAYAPPEAR IN THIS MANUAL, INCLUDING
THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Copyright © 2000 ASUSTeK COMPUTER INC. All Rights Reserved.
Product Name: ASUS P4T-M
Release Date: December 2000
2ASUS P4T-M Quick Setup Manual
1. FEATURES
1.1 P4T-M Motherboard Layout
Motherboard Layout
3. H/W SETUP
24.4cm (9.60in)
24.4cm (9.6in)
PS/2KBMS
T: Mouse
B: Keyboard
PCI1
PCI2
PCI3
PANEL
FLOPPY
SECONDARYIDE
PRIMARYIDE
Intel I/O
Controller
Hub
(ICH2)
P4T-M
CHA_FAN
Accelerated Graphics Port (AGP)
CR2032 3V
Lithium Cell
CMOS Power
Socket 423
COM1
PARALLEL PORT
RIMMB2 (16/18 bit, 184-pin module)
RIMMB1 (16/18 bit, 184-pin module)
ATX Power Connector
4Mbit
Firmware
Hub
RIMMA2 (16/18 bit, 184-pin module)
RIMMA1 (16/18 bit, 184-pin module)
Multi
I/O
ATX12V
Intel 850
Memory
Controller
Hub (MCH)
USB1
USB2
Bottom:
RJ-45
Top:
GAME_AUDIO
Mic
In
Line
Out
Line
In
VIDEO
AUX_CON
COM2
AFPANEL
Realtek
RTL8139C
CPU_FAN
PWR_FAN
USB2
Audio
Codec
WOLCON
NO_REBOOT
CLRTC
IDELED
CD_IN
Grayed components are available only on certain models at the time of purchase.
ASUS P4T-M Quick Setup Manual 3
1.2 Layout Contents
Expansion
1) RIMMA1/A2/B1/B2 p.18 184-Pin System Memory Support
2) CPU p.19 Central Processing Unit (CPU)6
3) PCI1/2/3/4/5 p.25 32-bit PCI Bus Expansion Slots
4) AGPPRO p.26 Accelerated Graphics Port (AGP Pro) Slot
Connectors
1) PRIMARY/SECONDARYIDE p.30 Primary/Secondary IDE Connectors (Two 40-1pins)
2) FLOPPY p.30 Floppy Disk Drive Connector (34-1pins)
3 CPU_FAN, PCI_FAN p.31 CPU, PCI, MAIN Fan Connectors (Three 3-pin)
MAIN_FAN
4) WOL p.32 Wake-On-LAN Connector (3 pins)
5) USB2 p.32 USB Header (10-1 pins)
6) IA p.33 Internal Audio (4-pin VIDEO, CD_IN, AUX)
7) AFPANEL p.33 Connector (5 pins)
8) ATXPWR, AUXPWR, p.34 ATX 12V Power Supply Connectors
ATX12V
9) PWRLED (PANEL) p.35 System Power LED Lead (3-1 pins)
10) KEYLOCK (PANEL) p.35 Keyboard Lock Switch Lead (2 pins)
11) SPEAKER (PANEL) p.35 System Warning Speaker Connector (4 pins)
12) MSG.LED (PANEL) p.35 System Message LED (2 pins)
13) SMI (PANEL) p.35 System Management Interrupt Switch Lead (2 pins)
14) PWRSW (PANEL) p.35 ATX Power / Soft-Off Switch Lead (2 pins)
15) RESET (PANEL) p.35 Reset Switch Lead (2 pins)
1. FEATURES
4ASUS P4T-M Quick Setup Manual
2. HARDWARE SETUP
2.1 Getting Started
IMPORTANT: Due to Pentium 4 CPU’s power consumption requirement, an
ATX12V power supply is recommended for this motherboard. For typical system
configurations, anATX12V power supply that can supply at least 230W and at least
8.5A on the +12V lead is required. For heavily-loaded configurations, an ATX12V
power supply that can supply at least 300W is required.
Before using your computer, you must complete the following steps:
• Check Motherboard Settings
• Install Memory Modules
• Install the Central Processing Unit (CPU)
• Install Expansion Cards
• Connect Ribbon Cables, Panel Wires, and Power Supply
WARNING! Computer motherboards and expansion cards contain very delicate
Integrated Circuit (IC) chips. To protect them against damage from static electric-
ity, you should follow some precautions whenever you work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do
nothaveone,touch both of your hands to a safely grounded object or to a metal
object, such as the power supply case.
3. Hold components by the edges and try not to touch the IC chips, leads or con-
nectors, or other components.
4. Placecomponents on a grounded antistaticpad or on the bagthat came with the
component whenever the components are separated from the system.
5. Ensure that the ATX power supply is switched off before you plug in or
remove the ATX power connector on the motherboard.
WARNING! Make sure that you unplug your power supply when adding or
removing system components. Failure to do so may cause severe damage to
your motherboard, peripherals, and/or components. The onboard LED when
lit acts as a reminder that the system is in suspend or soft-off mode and not
powered OFF.
ASUS P4T-M Quick Setup Manual 5
2. HARDWARE SETUP
2.2 System Memory
NOTE: No hardware or BIOS setup is required after adding or removing memory.
This motherboard has four 184-pin Rambus Inline Memory Modules (RIMM) sockets.
These sockets support 64Mbit, 128Mbit, and 256Mbit Direct RDRAM technologies.
IMPORTANT
1. The memory configuration of channelA(RIMMA1 and RIMMA2) and chan-
nel B (RIMMB1 and RIMMB2) must be identical (see below).
2. C-RIMMs (Continuity RIMM) must be used to complete the sockets that are
not populated by RDRAMs. A C-RIMM is necessary to avoid breaking the
signal lines, which are a serial connection in a Rambus interface, such as
used in this motherboard. This assures the electrical integrity of a Rambus
interface.
3. When C-RIMMs are required, it is recommended that they be inserted into
RIMMA2 and RIMMB2.
RIMMA1
RIMMA2
RIMMB1
RIMMB2
128MB RDRAM
128MB RDRAM
C-RIMM
C-RIMM
a.
RIMMA1
RIMMA2
RIMMB1
RIMMB2
128MB RDRAM
128MB RDRAM
128MB RDRAM
128MB RDRAM
c.
RIMMA1
RIMMA2
RIMMB1
RIMMB2
128MB RDRAM
128MB RDRAM
C-RIMM
C-RIMM
b.
Location Memory Module Subtotal
RIMMA1 RDRAM x1
(Rows 0&1) C-RIMM (use when socket will not be populated)
RIMMA2 RDRAM x1
(Rows 2&3) C-RIMM (use when socket will not be populated)
RIMMB1 RDRAM x1
(Rows 4&5) C-RIMM (use when socket will not be populated)
RIMMB2 RDRAM x1
(Rows 6&7) C-RIMM (use when socket will not be populated)
TOTALSYSTEM MEMORY =
(2GB Max)
NOTE: When using only two memory modules,
it is recommended that you use configuration a.
6ASUS P4T-M Quick Setup Manual
2. HARDWARE SETUP
2.2.1 Installing Memory
The memory module (RIMM/C-RIMM) will fit in only one orientation.
IMPORTANT:Do not touch the memory module’s connectors. Handle the mod-
ule only by the edges.
1. Make sure that the notch keys in the module are aligned with the small ribs
inside the RIMM sockets.
NOTCH KEYS
CONNECTORS
RDRAM (with heat spreader)MOUNTING NOTCH
RIBS (inside socket)
EJECTOR (TOP VIEW)
2. With the ejectors in the open position (as shown), push down gently but firmly
on the memory module until it snaps into place. The guides on the socket’s
ejectors should go through the two mounting notches on the module and the
ejectors should close. If necessary, push the ejectors inward to secure the mod-
ule in place.
Removing Memory
To release a memory module,pushboth ejectors outward and pull the module straight
up and out of the RIMM sockets.
WARNING! RIMM modules become extremely hot during operation. To re-
duce the risk of personal injury from hot surfaces, allow the modules to cool off
before removing them.
P4T-M
P4T-M 184-Pin RIMM Sockets
RIMM Sockets
RIMM with Heat Spreader
C-RIMM
ASUS P4T-M Quick Setup Manual 7
2. HARDWARE SETUP
2.3 Central Processing Unit (CPU)
The motherboard provides a ZIF Socket for the supported CPUs. The CPU that
came with the motherboard should have a fan attached to it to prevent overheating.
If this is not the case, then purchase a fan before you turn on your system.
P4T-M
P4T-M Socket 423
Gold Arrow
Socket 423 Pentium 4
Gold Arrow
Before you start, you should check to see that you have the following items:
(NOTE: Motherboard layout is not identical to the example.)
Rubber Pad Metal Baseboard
2 Metal heatsink retaining clips
4 Copper captive nuts
4 Pan Head screws
2 Heatsink support bases
4 Washers
8ASUS P4T-M Quick Setup Manual
2. HARDWARE SETUP
2.3.1 CPU Installation
Step 1: Install the Baseboard
A metal baseboard is required to install the heatsink to the motherboard. A rubber
pad is placed between the metal board and motherboard to provide insulation to
prevent shorting. (NOTE: Motherboard layout is not identical to the example.)
Rubber Pad Metal Baseboard
Align the rubber pad over
the metal baseboard so that
the holes match. Align the
motherboard over the rub-
ber pad and metal base-
board so that the screws on
the baseboard match up
with the motherboard’s
screw holes.
Placethefour washers over the four
screws on the baseboard. Tighten the four copper captive
nuts over the washers.
Motherboard
Washer
Washer
Copper captive nut
®
Motherboard
IMPORTANT:
This step is a M U S T! The washers
are necessary to prevent shorting.
ASUS P4T-M Quick Setup Manual 9
2. HARDWARE SETUP
Step 2: Install the CPU
A. Locate the ZIF socket on the motherboard.
B. Unlock the socket by pressing the lever sidesways and then lifting it up to a
90˚–100˚ angle.
C. Align the CPU over the socket such that its notched or marked corner matches
the socket’s corner near the end of the lever, while making sure that the CPU is
parallel to the socket.
D. Carefully insert the CPU into the socket until it fits in place. The illustration
below shows how to insert a CPU properly.
CAUTION!The CPU fits in only one orientation. Do not force the CPU into the
socket as it will bend the pins and damage the CPU. It should drop into the
socket with minimal pressure. If not, check its orientation or check for bent pins.
E. Secure the CPU into the socket by pushing the socket lever all the way down.
You will hear a click indicating that the lever is in place.
10 ASUS P4T-M Quick Setup Manual
2. HARDWARE SETUP
Step 3: Install the Heatsink Support Base
Place the two heatsink support base as shown and screw in the four pan head screws.
Step 4: Install the Heatsink
Carefully place the fan heatsink on top of the heatsink support base and connect the
fan power cable to the CPU fan connector.
Connect to the
CPU fan connector.
Andere Handbücher für P4T-M
1
Inhaltsverzeichnis
Andere Asus Hauptplatine Handbücher
Asus
Asus CUC2000-M Bedienungsanleitung
Asus
Asus PRIME H610M-F D4 Bedienungsanleitung
Asus
Asus PRIME H370-PLUS Bedienungsanleitung
Asus
Asus P5K PREMIUM/WIFI-AP - Pearl Special Edition... Bedienungsanleitung
Asus
Asus P4R800-V Deluxe Bedienungsanleitung
Asus
Asus P8H61-I LX R2.0 RM SI Bedienungsanleitung
Asus
Asus Z170 PRO GAMING/AURA Bedienungsanleitung
Asus
Asus P4B Bedienungsanleitung
Asus
Asus P4S333-VF Bedienungsanleitung
Asus
Asus C60M1-I Bedienungsanleitung
Asus
Asus H81M-P Bedienungsanleitung
Asus
Asus P7P55 - WS SuperComputer Motherboard Bedienungsanleitung
Asus
Asus EX-H110M-V Bedienungsanleitung
Asus
Asus P8P67 DELUXE Bedienungsanleitung
Asus
Asus Rampage II GENE - Republic of Gamers... Bedienungsanleitung
Asus
Asus P5K3 Premium WiFi-AP Bedienungsanleitung
Asus
Asus RAMPAGE V EDITION 10 Bedienungsanleitung
Asus
Asus H81M-V PLUS Bedienungsanleitung
Asus
Asus P5K3 Deluxe Bedienungsanleitung
Asus
Asus F1A75-M LE Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Texas Instruments
Texas Instruments ADS8372EVM Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
Intel
Intel D33217CK Bedienungsanleitung
