AT&T Teleworker Cisco 1101 Bedienungsanleitung

AT&T SD-WAN with Cisco –Telecommuter

Hardware Installation Quick Start Guide

This guide will help you through the following:

•Unboxing and performing the customer self-installation

•Service Activation

•Wi-Fi Setup

•Support after Service Activation

The following components are included in your Teleworker Cisco 1101

shipping box:

What’s in the Box

Cisco 1101 SD-WAN Router

Router power cable

RJ45 Ethernet cable

Site Documentation

Package

LTE Antenna

(Qty 2)

LTE Antenna (Optional)

Note: Please take a picture of all labels on the shipping box as they

have important equipment information.

Step 1 - Attach Power Cord, ethernet cable to Router

1. Determine suitable location within a few feet of your broadband residential

Internet gateway (modem/router)

2. Plug in one side of yellow ethernet cable*

3. Attach power cable and leave Power button off

4. If LTE is included, refer to step 3

On/Off Power

Button - Leave

powered off until

ready for service

activation

Power Cable-

Plug in

Ethernet Cable-

Plug one side into

port

Optional LTE

Card (Black)

* Note: Color of provided ethernet cable may vary

Step 2 –Connect the Teleworker equipment to your

broadband residential Internet gateway.

Connect the provided ethernet cable used in Step 1 to an available

ethernet LAN port on your broadband residential gateway.

Note: The broadband residential gateway pictured above may vary with your broadband service.

Residential gateway devices often have up to 4 ethernet ports.

Step 3 –Connect LTE Antenna (optional)

This step is only applicable if LTE option was purchased.

Optional LTE

A B

1. Unscrew the two grey caps labeled A and B on the

picture below

2. Screw on one antenna to connector A and one

antenna to connector B. Note: There is a pivot

joint on each antenna that can be pivoted upward.

What’s next

Service Activation

Once you have completed the self-installation of your Teleworker

equipment, please contact AT&T at 866-204-0852 PIN 10002 to activate

your service. Hours of operation are 8am-5pm Eastern Standard Time

Monday-Friday. Please note that if you cannot schedule a time within 10

days of receiving your equipment, your service will start billing on day

11.

After the service activation call has completed, proceed to the next step

of setting up Wi-Fi on your device.

Note: Should equipment issues arise where your equipment is not functioning, AT&T may need to replace

your equipment. AT&T will advise during the Service Activation if this needs to take place and replacement

equipment will be ordered.

Setting up Wi-Fi on Telecommuter Equipment

When the Wi-Fi LED on the Access

Point blinks green, connect a Wi-Fi

enabled device (laptop, desktop or

tablet) to the CiscoAirProvision Wi-Fi

Name (SSID) from your list of

available Wi-Fi networks on your

device.

Note: The default Wi-Fi password is:

password (all lower case)

and will only be used for initial setup.

Wi-Fi Light will blink Green

Note: Page 14 has a listing of settings you

create on the following pages that you can

write down to refer back to later.

Setting up Teleworker Wi-Fi

•Open a web browser on your

device and type:

http://mobilityexpress.cisco

This will start the configuration

wizard and the admin account page

will appear.

•Create an admin account to login

to the Wi-Fi device by creating a

username and password then

click on the Start button.

Note: “myname” and other entries on the following

pages including “System Name” and “Network

Name” are illustrative and your selections should be

different.

The password must contain characters from at least three

of the following classes –lowercase letters, uppercase

letters, digits, special characters. Max length is 24.

Setup your Controller

In the Set up Your Controller section,

configure the following:

•System Name –Enter a system

name to identify your device

•Enter Country/Date & Time /

Timezone if not already populated

•NTP Server –Leave blank

•Enable IP Management and Mesh

- Leave unselected

•Enable DHCP Server –Leave

unselected

•Click Next

Create Wireless Network

In the Create Your Wireless Network,

under Employee Network, configure

the following:

•Network Name –Enter a Wi-Fi

Name (SSID) you wish to use. This

name will show up on your

device(s) as your Teleworker Wi-Fi

network to connect to.

•Security –Leave at WPA2 Personal

if your company does not suggest

other.

•Passphrase –Enter a Wi-Fi

Password

•Confirm Passphrase –Type Wi-Fi

Password again

•Click Next

Inhaltsverzeichnis

Andere AT&T Schnurloses Telefon Handbücher

AT&T

AT&T CLP99286 Bedienungsanleitung

AT&T

AT&T DECT EL51359 Bedienungsanleitung

AT&T

AT&T E560-2 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

AT&T

AT&T EL41108 Bedienungsanleitung

AT&T

AT&T 1231 Bedienungsanleitung

AT&T

AT&T EL52113 Bedienungsanleitung

AT&T

AT&T EL52109 - AT&T DECT 6.0 Bedienungsanleitung

AT&T

AT&T CL82203 Bedienungsanleitung

AT&T

AT&T EL52265 Bedienungsanleitung

AT&T

AT&T CL81101 Bedienungsanleitung

AT&T

AT&T CL82309 Bedienungsanleitung

AT&T

AT&T TL9228 Bedienungsanleitung

AT&T

AT&T HS-8210 Bedienungsanleitung

AT&T

AT&T EL52200 Bedienungsanleitung

AT&T

AT&T 7650 Bedienungsanleitung

AT&T

AT&T CL81109 Bedienungsanleitung

AT&T

AT&T CL84107 Bedienungsanleitung

AT&T

AT&T 1485 Bedienungsanleitung

AT&T

AT&T E5655 Bedienungsanleitung

AT&T

AT&T SL87218 Bedienungsanleitung

AT&T

AT&T 6200 Bedienungsanleitung

AT&T

AT&T E5908 Bedienungsanleitung

AT&T

AT&T TL92270 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

Panasonic

Panasonic KX-TGP700 Bedienungsanleitung

GE 27930 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung