AT&T 145 Bedienungsanleitung

RINGER OFF LO HI TONE PULSE

456

ABC DEF

GHI JKL MNO

PQRS

TUV WXYZ

TONE OPER

MEMORY PROGRAM FLASH REDIAL

Design Line Telephone 145

USER’S MANUAL

Part 2

AT&T and the globe symbol are registered trademarks of AT&T Corp.

licensed to Advanced American Telephones.

Printed in China. 850003054 Issue 1AT&T 6/00

Please also read

Part 1 — Important

Product Information

Dial Mode

This telephone has a selectable push-button dial and will

work with either tone or rotary telephone service. It can

be set to work directly with long-distance or certain other

services that require tone signaling including some tone

activated computer systems.

RINGER OFF LO HI TONE PULSE

456

ABC DEF

GHI JKL MNO

PQRS

TUV WXYZ

TONE OPER

MEMORY PROGRAM FLASH REDIAL

Dial Mode

switch

INSTALLATION

Temporary

Tone

Handset

Redials

last call

made

Accesses numbers

stored in memory

Receiver Volume

(on left side of base)

Ringer

Volume

Programs a number

in memory

Accesses custom

calling services

TABLE/DESK INSTALLATION

This telephone includes a 7-foot line cord with a modular

plug on each end. You’ll use this cord to connect the

telephone to a modular jack.

1. Connect line cord to telephone

Plug the long line cord into the jack on the underside of

the telephone base. Then feed the line cord through the

channel provided so the telephone sits flat on your table

or desk during use.

2. Set Dial Mode switch

This product comes set in the TONE mode. Make sure

you choose the correct dialing method (TONE/PULSE);

touch tone dialing will not work if you have dial pulse

service.

3. Connect handset to base

Plug one end of the coiled cord into the handset, and

the other end into the telephone base. Then hang up.

4. Connect line cord to modular jack

Plug the free end of the line cord into a modular jack.

Make sure it snaps firmly in place.

5. Check for dial tone

Lift the handset and listen for a dial tone. If you can’t

hear a dial tone, refer to “In Case of Difficulty” and try

to correct the problem.

TO DISCONNECT the telephone, squeeze the clip on

the modular plug and pull it out of the jack.

INSTALLATION

WALL INSTALLATION

1. Reverse the handset tab.

When mounting the telephone on a wall, you must

reverse the handset tab. This tab holds the handset when

you hang up. Hold down the switchhook, and slide the

tab up and out of its slot (Figure 1). Turn the tab so that

the end with the “hook” is up (Figure 2). Then insert the

tab back into its slot (Figure 3).

2. Fill in directory card

The enclosed directory card has an adhesive backing

which lets you place it in a convenient location near the

telephone. Write in your own telephone number and up

to nine other numbers you want to remember on the

directory card.

3. Plug the line cord into the jack on the underside of

the base

Feed the short line cord into the channel. Feed the last

portion (as short as possible), through one of the slots in

the mounting area.

4. Install telephone base on wall jack

Hold the base up next to the wall jack and plug in the line

cord. Then push the base against the wall jack and down

until it is held securely by the mounting studs.

INSTALLATION

Figure 1 Figure 2 Figure 3

5. Set the Dial Mode switch

This product comes set in the TONE mode. Make sure

you choose the correct dialing method (TONE/PULSE);

touch tone dialing will not work if you have dial pulse

service.

6. Connect handset to telephone base

Connect one end of the coiled handset cord to

the base. Plug the other end into the handset. Then hang

up the phone.

7. Check for dial tone

Lift the handset and listen for a dial tone. If you can’t

hear a dial tone, refer to “In Case of Difficulty” and try

to correct the problem.

NOTE: If you cannot fit the base onto the wall jack plate,

remove the top two non-slip feet.

INSTALLATION

Line Jack

Figure 4

Handset

Jack

Wall Jack

Redial

The telephone always stores in memory the last number

dialed. To dial the same number again, lift the handset, and

press .

The redial memory can accept numbers up to 32 digits long.

The number will remain in memory until you change it by

dialing another telephone number.

For privacy, you can erase the redial memory. Lift the

handset, then press any digit (1-9).

Flash

Press instead of pressing the switchhook to activate

customer calling services such as call waiting or three-way

calling. You may have to press other buttons before or after

as explained in custom calling instructions provided

by your local telephone company.

Ringer Volume

The RINGER volume switch allows you to adjust the loud-

ness of the telephone ringer from OFF to LO to HI. Slide

the switch to the desired volume level.

Receiver (Handset) Volume

The Receiver volume switch on the left side of the base has

three positions which allow you to adjust the loudness of

your call from NORMAL to LOUD. Slide the switch to the

desired volume level.

Temporary Tone

Temporary tone dialing is used only when you have rotary

service. It allows you access to services that require tone

signaling, including some tone-activated computer systems

(e.g., telephone banking).

To change from pulse (rotary) to tone dialing during a call:

1. Dial a telephone number with the dial mode switch set to

PULSE.

2. Press ; all buttons pressed after this will send

tone signals.

3. After you hang up, the phone automatically returns to

rotary service.

TONE

FLASH

REDIAL

OPERATION

Memory Features

Numbers will remain stored in memory unless you erase or

change them by entering other numbers.

Capacity: This telephone can store up to nine different

phone numbers, each up to 18 digits long.

Speed Dialing: Nine telephone numbers can be stored in

standard speed-dialing locations. You can dial any of these

numbers by pressing two buttons.

NOTE: Numbers programmed into a memory location

might not be retained if the telephone has been unplugged

from the line jack for a half hour or more.

Speed Dialing

To program numbers into memory:

1. Press .

2. Enter telephone number. You will hear a click when

each button is pressed.

3. Press .

4. Enter a digit (1-9) for the memory location where the

number is to be stored.

5. Hang up after the number is entered correctly.

Repeat steps 1-5 to store another number.

To dial:

1. Listen for dial tone.

2. Press .

3. Press memory location (1-9).

Memory Erase

To erase any number from memory, you can enter another

number in the same location.

MEMORY

PROGRAM

MEMORY

If you have difficulty operating this phone, try the

suggestions below.

No Dial Tone

☞Make sure all plugs are connected properly. Inspect

the line cord connections at the modular jack and at

the telephone. Also inspect the coiled handset cord

connections at both ends.

☞Unplug the telephone and connect it to another modular

jack. If it still does not work, try another telephone; if

neither telephone works, the problem is not in this

telephone. The trouble may be caused by local telephone

company lines, central office equipment, or the wiring

in your home.

Calls Cannot Be Dialed, or Are Dialed Slowly

Reset Dial Mode switch. If you have rotary service, you

cannot dial numbers with the switch set to TONE. Set the

switch to PULSE, then hang up and dial again.

If you have tone dialing service, you can use either tone or

dial-pulse mode. If you set the switch to TONE, numbers

are dialed much more quickly.

Telephone Does Not Ring

☞Make sure the Ringer switch is not set to OFF.

☞If there are several other phones on the same line, try

disconnecting some of the other telephones. Having too

many telephones can also create problems such as low

ringer volume or impaired quality during calls.

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Axess Telecom

Axess Telecom ACW-1xP800 Bedienungsanleitung