AT&T EL42208 Bedienungsanleitung

Telephone base & charger installation

If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL)

through your telephone lines, you must install a DSL filter between the

telephone base and the telephone wall jack. The filter will prevent noise

and caller ID problems caused by DSL interference. Please contact your DSL

service provider for more information about DSL filters.

Install the telephone base and charger as shown below.

NOTES:

1. Use only the supplied rechargeable battery, replacement battery (part numberUse only the supplied rechargeable battery, replacement battery (part number

89-1332-00-00) or equivalent. To order a replacement battery, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial

1 (866) 288-4268.

2. This power adapter is intended to be correctly oriented in a vertical or floor mount position.

The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

Getting started

Telephone line cord

DSL filter

(available from your DSL Internet

provider)

4. Plug the other

end of the

telephone line

cord into a

telephone jack.

5. Plug the

large end of

the power

adapter into an

electrical outlet

not connected

to a wall switch.

3. Route cords

through slots.

2. Plug one end of

the telephone

line cord into the

telephone jack

on the underside

of the telephone

base.

1. Plug the small

end of the power

adapter into the

power jack on

the underside of

the telephone

base.

Plug the power

adapter into an

electrical outlet not

connected to a wall

switch.

Charger installation

Telephone base installation

Installation options

The telephone base is designed for both desktop installation and wall mount

installation. If wall mounting is desired, a telephone outlet wall mounting

plate with mounting studs is required. This mounting plate is available for

purchase at many hardware or consumer electronics retailers and may require

professional installation.

Desktop to wall mount installation

1. Plug the telephone line

cord and power adapter

into the telephone base.

Bundle the telephone

line cord and route cords

through the slots, then

secure with a twist tie.

2. Plug the power adapter

and telephone line cord

into the wall outlets, then

align the mounting studs

on the telephone outlet

plate with the mounting

holes on the telephone

base.

3. Place the telephone

base mounting holes

just above the mounting

studs, then slide the

telephone base down

until it is secure.

Getting started

Installation options

Wall mount to desktop installation

To change the telephone base from the wall mount position to desktop

position, make sure that you first unplug the power adapter and telephone

line cord from the wall outlets before you begin.

1. Slide the telephone base

upwards, then pull the

telephone base away from the

wall off of the mounting studs.

2. Unplug the power adapter and

the telephone line cord from

the electrical outlet and the

telephone jack.

3. Plug the telephone line cord

into the telephone base and

telephone wall jack, then plug

the power adapter plug into the

telephone base and a power

outlet not connected to a wall

switch.

Getting started

Battery installation & charging

Install the battery as shown below. After installing the battery, you can make

and receive short calls, but replace the handset in the telephone base or

charger when not in use. For optimal performance, charge the handset battery

for at least 16 hours before use. When fully charged, the handset battery

provides approximately five hours of talk time or six days of standby time.

If the handset has not been used for a long time or if the battery inside is

completely depleted, put it on the telephone base or charger for recharging.

Getting started

RECORD

ANNC.

REMOVE

MENU / SEL

TRANSFER

Step 1

Insert the battery plug as

indicated, making sure that

it matches the color-coded

label inside the battery

compartment.

Step 4

Charge the handset, by placing the

handset face up in the telephone

base. The CHARGE light on the

handset should be on as soon as

the handset is properly placed on

the telephone base.

Step 3

Slide the battery

compartment cover

up until it clicks.

Step 2

Place the battery

and wires inside the

compartment.

CHARGE

light

Getting started

Battery installation & charging

Low battery indicator

Return the handset to the telephone base or charger to

recharge when this symbol flashes and the handset beeps

or when the handset screen displays LOW BATTERY.

IMPORTANT INFORMATION

Use only the supplied rechargeable battery, replacement battery (part number 89-1332-00-00) or

equivalent. To order a replacement battery, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial

1 (866) 288-4268.

To replace the battery, press the tab and slide the

battery compartment cover downwards. Lift out the old

battery and disconnect it from the handset. Follow the

instructions on the previous page to install and charge the

new battery.

LOW BATTERY

10:08AM

02/14

Settings

Each cordless handset operates independently

from the other handsets. The ringer sound,

ringer volume, date and time, dial mode, home

area code and language must be programmed

separately for each cordless handset.

To customize how the handset works:

1. Press MENU/SEL in the idle mode to enter the

handset main menu.

2. Use CID or DIR to scroll to the desired

feature.

3. Press MENU/SEL to select the feature.

To stop at any time, press OFF/CLEAR.

Language

To change the language to Espanol, or Francais:

1. Press MENU/SEL in the idle mode to enter the

handset main menu.

2. Press CID or DIR until the screen displays

LANGUAGE.

3. PressPress MENU/SEL. The current setting is flashing.

4. Press CID or DIR to choose ENGLISH,

FRANCAIS, or ESPANOL.

5. Press MENU/SEL to save your selection and

return to the main menu.

Dial mode

The dial mode defaults to tone. If you do not have

touch tone service, you will need to change the

setting to pulse:

1. Press MENU/SEL in the idle mode to enter the

handset main menu.

2. Press CID or DIR until the screen displays

DIAL MODE: and the current setting.

3. Press MENU/SEL. The current setting is flashing.

4. Press CID or DIR to display TONE or

PULSE.

5. Press MENU/SEL to save your selection and

return to the main menu.

LANGUAGE

DIAL MODE: TONE

Telephone operation

Andere Handbücher für EL42208

Inhaltsverzeichnis

Andere AT&T Telefon Handbücher

AT&T

AT&T 929 Bedienungsanleitung

AT&T

AT&T Synapse Bedienungsanleitung

AT&T

AT&T 929 Bedienungsanleitung

AT&T

AT&T 272 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

AT&T

AT&T SynJ SB67148 Bedienungsanleitung

AT&T

AT&T Merlin II Release 3 Bedienungsanleitung

AT&T

AT&T Partner MLS 34D Bedienungsanleitung

AT&T

AT&T 1070 Bedienungsanleitung

AT&T

AT&T 1187 Bedienungsanleitung

AT&T

AT&T ML17928 Bedienungsanleitung

AT&T

AT&T Synapse SB67020 Bedienungsanleitung

AT&T

AT&T 1080 Bedienungsanleitung

AT&T

AT&T CL2909 Bedienungsanleitung

AT&T

AT&T CL2909 Bedienungsanleitung

AT&T

AT&T Disk Bedienungsanleitung

AT&T

AT&T ATT950 Bedienungsanleitung

AT&T

AT&T 950 Bedienungsanleitung

AT&T

AT&T Four-Line Intercom Speakerphone 974 Bedienungsanleitung

AT&T

AT&T Definity 7313H Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

AT&T

AT&T TL90031 Bedienungsanleitung

AT&T

AT&T CL83215 Bedienungsanleitung

AT&T

AT&T Merlin Legend MLX-20L Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Axess Telecom

Axess Telecom ACW-1xP800 Bedienungsanleitung