AT&T Trimline 230 Bedienungsanleitung

TRIMLINE

Memory

Telephone 230

User’s Manual

Part 2

Printed in Mexico. 848234530 Issue 1AT&T

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 1

PARTS CHECKLIST

Remember to save your sales receipt in case you ever

need warranty service, and make sure this telephone

package includes the items shown below:

TELEPHONEBASE

TELEPHONE

HANDSET

Handset Tab

Switchhook

Coiled handset cord7-foot line cord

Ringer

Volume

Receiver

Volume

Program

Button

Dial

Mode

Switch

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 2

TABLE/DESK INSTALLATION

This telephone includes a 7-foot line cord with a

modular plug on each end. Use this cord to connect

the telephone to a modular jack.

1. Fill in directory card

Remove the directory card and

write in your own telephone

number. Also write the tele-

phone numbers (or names)

that you want to store in each

memory location.

Reinstall the card and clear

plastic cover.

2. Connect line cord to telephone

Plug the long line cord into the

jack on the underside of the tele-

phone base. Then feed the line

cord through the channel pro-

vided so the telephone sits flat

on your table or desk during use

(Figure 1).

3. Connect line cord to wall jack

Plug free end of

the line cord into a modular

jack. Make sure it snaps firmly

into place.

4. Set DIAL Mode switch

This product comes set in the

tone (TT) mode. Make sure you choose the

correct dialing method (TT/DP); touch tone dial-

ing will not work if you have dial pulse service.

5. Connect handset to base

Plug one end of the coiled handset cord into the

handset, and the other end into the base. Then

hang up.

6. Check for dial tone

Lift the handset and listen for dial tone. If you can-

not hear a dial tone, refer to “In Case of Difficulty”

and try to correct the problem.

TO DISCONNECT the telephone, squeeze the

clip on the modular plug and pull it out of the jack.

Figure 1

Figure 2

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 3

WALL INSTALLATION

1. Fill in directory card

Remove the directory card and write in your own

telephone number. Also write the telephone num-

bers (or names) that you want to store in each

memory location.

2. Reverse handset tab

To install the telephone on a wall jack, you must

reverse a small tab beneath the directory card. This

tab holds the handset in place when you hang up.

Remove the directory card and plastic cover. Use

a paper clip to lift and remove the handset tab.

Reverse the tab and reinstall it as shown (Figure

1). Then replace the directory card and cover.

3. Plug the line cord into the

jack on the underside of the

base. Feed the line cord into the

channel and wind it around the

mounting area. Feed the last

portion (as short as possible),

through one of the slots in the

mounting area (Figure 2).

(Continued)

Figure 2

Figure 1

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 4

WALL INSTALLATION (continued)

4. Install telephone

base on wall jack

Hold the base up

next to the wall jack,

and plug in the line

cord (Figure 3).

Then push the base

againstthe wall jack

and down until it is

held securely by the

mounting studs.

5. Set DIAL Mode switch

Refer to step 4 in Table/Desk Installation.

6. Connect handset to telephone

Connect one end of the coiled handset cord into

the base. Plug the other end into the handset

(Figure 4). Then hang up.

7. Check for dial tone

Lift the handset and listen for dial tone. If you

cannot hear a dial tone, refer to “In Case of

Difficulty” and try to correct the problem.

NOTE: If you

cannot fit the base

onto the wall jack,

remove the four

non-slip pads.

Figure 4

Figure 3

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 5

OPERATION

Redial

This telephone always stores in memory the last

phone number dialed.

The redial memory can accept numbers up to 24

digits long. The number will remain in memory until

you change it by dialing another telephone number.

To dial the same number again, lift the handset, and

press .

Erasing Redial

For privacy, you can erase the redial memory. Lift the

handset, then press and hang up.

Mute

Hold down to turn off the handset micro-

phone. You will still be able to hear the other person,

but anything you say will not be heard.

Flash

Press then instead of pressing the

switchhook to activate custom calling services such

as call waiting or 3-way calling.

You may have to press other buttons before or after

Flash as explained in custom calling instructions

provided by your local telephone company.

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 6

Ringer Volume

The Ringer Volume switch allows you to turn the

telephone ringer OFF, or set it to ring at LO or HI

volume. You can dial or answer calls normally when

the ringer is off. Other telephones in your home will

still ring; they are not affected by the switch.

Receiver (Handset) Volume

The Receiver Volume switch on the side of the hand-

set can be adjusted for a comfortable listening level.

The switch has three volume positions.

Temporary Tone Dialing

Temporary tone dialing

is used only when you

have rotary service. It

allows you access to

services that require

tone signaling, includ-

ing some tone-activated

computer systems (e.g.,

telephone banking).

To change from pulse

(rotary) to tone dialing

during a call:

1. Dial a telephone

number with the DIALMode switch set to

PULSE.

2. Press ; all buttons pressed after this will

send tone signals.

3. After you hang up, the phone automatically

returns to rotary service.

OPERATION (continued)

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 7

MEMORY DIALING

Memory Features

Numbers will remain stored in memory unless you

erase or change them by entering other numbers.

Capacity: This telephone can store up to 12 different

phone numbers, each up to 24 digits long.

One-Touch Dialing: Three numbers can be stored in

one-touch memory locations. You can dial these

numbers by pressing one of the buttons marked with

an emergency symbol.

Speed Dialing: Nine telephone numbers can be

stored in standard speed-dialing locations. You can

dial any of these numbers by pressing two buttons.

Directory Card: Remove the directory card. Write

your telephone number in the space provided. Also

write the telephone numbers (or names) that you want

to store in each memory location. Reinstall the card

and clear plastic cover.

NOTE: Numbers programmed into a memory

location might not be retained if the telephone has

been unplugged from the line jack for a half hour

or more.

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 8

Emergency Numbers: You may choose to store

emergency numbers in the one-touch memory loca-

tions marked with fire, police and medical symbols.

However, we recommend that you also write the

telephone number on the directory card so that if

the memory feature does not function, you can still

manually dial an emergency number.

If you choose to store non-emergency numbers in

these locations, it is important to remember that

someone visiting your household may assume that

they are dialing an emergency telephone number

when they press one of these emergency symbols.

NOTE: Although testing the programming of emer-

gency numbers is nota recommended procedure, if

you do make a call to an emergency number:

A. You must remain on the line and briefly explain

the reason for the call before hanging up.

B. Programming/testing of emergency numbers

should be performed in the early morning or

late evening (off-peak hours).

NOTE: You may choose to store emergency

numbers in memory locations marked with fire,

police and medical symbols. However, speed

dialing and emergency calling symbols are

provided only as a convenience. The manufacturer

does not assume responsibility for customer

reliance upon this memory feature.

MEMORY DIALING (continued)

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 9

One-Touch Dialing

To program numbers into memory

1. Press .

2. Enter telephone number. You will hear a click

when each button is pressed.

3. Press the memory button , or , where

the number is to be stored.

4. Hang up after the number is entered correctly.

Repeat steps 1-4 to store another number.

To dial

1. Listen for dial tone.

2. Press the one-touch memory button

( , or ,). (continued)

(Turn over for more Memory

Dialing and In Case of Difficulty)

1. Press .

2. Enter telephone

number.

3. Press the

one-touch

memory

button.

MEMORY DIALING (continued)

AT&T 230 Quark pdf 7/22/98 12:13 PM Page 10

Inhaltsverzeichnis

Andere AT&T Telefon Handbücher

AT&T

AT&T Bell System 564HK Bedienungsanleitung

AT&T

AT&T Trimline TR1909 Bedienungsanleitung

AT&T

AT&T 915 Bedienungsanleitung

AT&T

AT&T 950 Bedienungsanleitung

AT&T

AT&T CL83203 Bedienungsanleitung

AT&T

AT&T 1855 - AT&T Corded Phone Bedienungsanleitung

AT&T

AT&T MERLIN LEGEND MLX-10 Non-Display Telephone Bedienungsanleitung

AT&T

AT&T 5870 Bedienungsanleitung

AT&T

AT&T 27020 Bedienungsanleitung

AT&T

AT&T 950 Bedienungsanleitung

AT&T

AT&T Merlin Bedienungsanleitung

AT&T

AT&T SPIRIT 2448 Expansion Unit Stücklistenhandbuch

AT&T

AT&T Partner 34D Bedienungsanleitung

AT&T

AT&T HS-8270 Bedienungsanleitung

AT&T

AT&T SB3014 Bedienungsanleitung

AT&T

AT&T 1856 - Corded Speakerphone Bedienungsanleitung

AT&T

AT&T System 75 Bedienungsanleitung

AT&T

AT&T 940 Series Leitfaden

AT&T

AT&T CL82100 Bedienungsanleitung

AT&T

AT&T CRL32302 Bedienungsanleitung

AT&T

AT&T CL82115 Bedienungsanleitung

AT&T

AT&T CL84115 Bedienungsanleitung

AT&T

AT&T TL92271 Bedienungsanleitung

AT&T

AT&T CL4940 Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung

Ericsson

Ericsson Dialog 3213 Bedienungsanleitung

Yealink

Yealink VP530 Bedienungsanleitung

Axess Telecom

Axess Telecom ACW-1xP800 Bedienungsanleitung