ATD Tools ATD-10528 Bedienungsanleitung

ATD-10528

4PC 18V LITHIUM ION CORDLESS COMBO KIT

Instruction Manual

Cordless Drill

PRT10528-01

Please read this MANUAL carefully before using the tool.

PRODUCT SPECIFICATIONS

Rated Voltage 18V DC

No-load Speed 0~350 / 0~1200Rpm

Chuck ½’’ Jacob Single Sleeve Chuck

Max Torque 22N.M (16.2 lb.ft)

Torque Setting 19+1

Charge Time 3~5 hours

Product Features

Operation

Only use tool bits which can be securely fastened in the chuck and for which the drill has been designed.

1. Drilling

Check whether the drill bit is correctly inserted and tightly fastened before you start the machine. Use properly

sharpened drill bits. Use screwdriver bits that are not overly worn.At the start of each drilling operation select a

lower speed. For large holes drill with a smaller drill bit first and then enlarge the hole using a larger drill bit.

2. Drilling in Wood

For drilling in wood use a wood drill-bit. Protect or fasten the work-piece in a suitable holder. Mark the positions

of the holes to be drilled with a sharp tool or a nail. Do not apply excessive pressure against the work-piece with

the drill.

3. Drilling in Metal

For drilling in metal use a steel drill-bit.Always provide sufficient cooling with suitable non-flammable coolants.

Protect or fasten the work-piece with a suitable holder. The work-piece should lie flat on the work bench. Mark

the positions of the holes to be drilled with a center-punch. Do not apply excessive pressure against the

work-piece with the drill.Allow the drill to operate at its normal operating speed.

Important! When beginning to drill, select a lower speed to avoid the bit slipping away from the desired hole

location. If the hole is deep, the drill bit may become jammed in the hole. In this event a high torque could

damage the drill bit or the drill. If the bit becomes jammed, hold the drill firmly and immediately release the

On/Off trigger. Switch to counter-clockwise rotation, and use a low rotation speed to remove the jammed drill bit

more easily.

1. LED work light

2. Variable speed trigger

3. Bit holder

4. Battery

5. High/low gear slide switch

6. Forward/Reverse switch

7. Soft grip handle

8. Battery lock button

4. Drilling in Plastic

For drilling in plastic use a steel drill bit and follow the same instructions as for drilling in wood.

5. Drilling in Stone, Brick, Masonry

For drilling in walls, stone, masonry etc. use a masonry-bit. Do not put too much pressure on the machine.

Follow the same instructions as for drilling in metal.

6. Using the drill as a screwdriver

Before using the machine check whether the screwdriver bit is inserted correctly. Avoid over-tightening screws,

otherwise the screw head may be damaged or stripping of the threads may occur.

7. Screw insertion

Set the direction of rotation of the drill to the clockwise direction. Insert the screwdriver bit into the slot in the

head of the screw. Hold the screw bit perpendicular to the head of the screw, otherwise the screw or the screw

head may be damaged. Press the screw bit against the screw with a constant pressure while driving in the

screw. When the screw is completely screwed in, hold the drill firmly and release the On/Off trigger, otherwise

the screw or the screw head may be damaged. If the On/Off trigger is not released immediately, high torque

could also damage the drill bit or the drill.

8. Screw removal

Set the direction of rotation of the drill to the counter-clockwise direction. Insert the screw-bit into the slot in the

head of the screw. Hold the screwdriver bit perpendicular to the head of the screw, otherwise the screw or the

screw head may be damaged. Press the screw bit against the screw with a constant pressure while removing

the screw.

Cordless Impact Wrench

PRT10528-02

PRODUCT SPECIFICATIONS

Rated Voltage 18V DC

Impact Power 0~3000 Ipm

No-load Speed 0~2000 Rpm

Anvil Size ½”

Rate Torque 230 N.M (169.7 ft.lb)

Max Torque 280 N.M (206.6 ft.lb)

Charge Time 3~5 hours

Product Features

1. LED work light

2. Variable speed trigger

3. Battery

4. Forward/Reverse switch

5. Soft grip handle

6. Battery lock button

Assembly

Selecting Correct Socket

Always use the correct size socket for bolts and nuts.

An incorrect size socket will result in inaccurate and inconsistent

fastening torque and /or damage to the bolt or nut.

Installing or Removing Socket

Always be sure that the tool is switched off and the battery pack is

removed before installing or removing the socket.

To install the socket, push it onto the anvil of the tool until it locks

into place. To remove the socket, simply pull it off.

Operation

Loosening nuts and bolts

Install socket as shown above. Place impact wrench and socket over nut or bolt making sure you have the

correct size and type of socket needed. Be sure impact wrench and socket are square with the nut or bolt.

Switch impact into the counter-clockwise direction and pull the variable speed trigger switch until nut or bolt is

removed. For stubborn nuts or bolts, a loosening agent may be needed prior to removing.

Tightening nuts and bolts

Start your nut or bolt by hand to ensure that you are not cross threading it. Be certain all threads are clean and

free of defects before tightening. After hand starting your nut or bolt, place impact wrench and socket over nut

or bolt making sure you have the correct size and type of socket needed. Be sure impact wrench and socket

are square with the nut or bolt. Switch impact into the clockwise direction and pull the variable speed trigger

switch until nut or bolt is tightened.

Cordless Reciprocating Saw

PRT10528-05

Technical Data

Rated Voltage DC 18V

No-load Speed 0-2800/min

Stroke length 22mm (0.87’’)

Charging Time 3-5 hours

Product Features

1 2 3 4 5

61. Adjustable pivoting blade shoe

2. Soft touch front handle

3. Variable speed trigger switch

4. Battery

5. Battery lock button

6. Soft grip handle

7. Lock-off switch

ASSEMBLY

WARNING:

Always remove battery pack from your saw when you are assembling parts, making adjustments,

assembling or removing blades, cleaning, or when not in use. Removing battery pack will prevent

accidental starting that could cause serious personal injury.

Inserting/Removing Battery Pack

TO INSERT:

1. To insert the battery pack by sliding battery pack into the body of the tool. Insert the battery pack until

the battery latches lock.

TO REMOVE:

1. To remove the battery pack, press in both battery latches and slide the battery pack off of the tool.

2. Make sure the latches on each side of the battery pack slip into place and battery pack is

secured to saw before beginning operation.

TO INSTALL SAW BLADE (Fig. 4)

1. Remove battery pack first.

WARNING:

Failure to remove battery pack from saw could

result in accidental starting causing possible

serious personal injury.

2. Loosen the blade clamp screw enough to

permit the saw blade to be inserted between

blade clamp and saw bar, by the blade wrench.

Note: it is never necessary to remove the blade

clamp screw from the blade clamp when

installing or removing blade.

3. Align the hole in the shank of the blade and blade clamp with the pin in the saw bar, and then seat both

on the pin in the saw bar.

Note: The wrench hole is used for wrench to

install the blade.

4. Tighten blade clamp screw securely.

5. Remove blade wrench and store it.

6. Replace battery pack.

Note: there may be times when the blade clamp

sticks to the saw bar and will not loosen enough

to allow blades to be installed or removed. If this

happens, loosen the blade clamp screw with the

blade wrench, then tap lightly on the end of the

blade wrench with a mallet. (Fig. 5)

GENERAL CUTTING (Fig. 6)

Hold your saw firmly in front of and clearly

away from you. Make sure saw blade is clear of

any foreign material. Be sure material to be cut

is held firmly. Small work pieces should be

securely clamped in a vise or with clamps to the

work bench or table. Mark the line of cut clearly.

Depress the lock-off button, then pull switch

trigger to start the cutting action.

Place the base assembly against the work piece.

Then move the blade into the work piece. Do not

force. Use only enough pressure to keep the

saw cutting. Let the blade and saw do the work.

Use of excessive pressure that causes bending

or twisting of the blade may result in broken

blades.

PLUNGE CUTTING (Fig. 7)

Mark the line of cut clearly. Choose a convenient

starting point inside the area to be cut out and

place the tip of the blade over that point. Rest

front edge of base (shoe) on work and hold

firmly in position. Depress the lock-off button,

then pull switch trigger to start the cutting action.

WARNING:

Make sure blade does not touch work until motor

reaches full speed, since this could cause loss

of control resulting in serious injury. With saw

blade at full cutting speed, slowly tilt saw

down-ward until tip of blade starts cutting work.

After blade penetrates work, tilt saw until blade

is perpendicular to the work.

METAL CUTTING (Fig. 8)

Metals such as sheet steel, pipe, steel rods ,

aluminum, brass and copper may be cut with

your saw. Be careful not to twist or bend the saw

blade. Do not force. We recommend cutting oil

when cutting most soft metals and steel. Cutting

oil will also keep blades cool, increase cutting

action, and prolong blade life. Never use

gasoline since normal sparking of motor could

ignite fumes. Clamp the work firmly and cut

close to the clamping point to eliminate any

vibration of the work being cut. When cutting

conduit pipe or angle iron, clamp work in a vise if

possible and cut close to the vise. To cut thin

sheet material, "sandwich" the material between

hardboard or plywood and clamp the layers to

eliminate vibration and material tearing.

WARNING

To reduce the risk of injury, be sure the blade always extends beyond the shoe and work piece

throughout the stroke. Blades may shatter if they impact the work-Piece or shoe.

WARNING

To reduce the risk of injury, Keep hands away from the blades and other moving part, always wear safety

goggles or Glasses with side shields. Use only specifically recommended.

Inhaltsverzeichnis

Andere ATD Tools Elektrowerkzeuge Handbücher

ATD Tools

ATD Tools ATD-3740 Bedienungsanleitung

ATD Tools

ATD Tools ATD-5800A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7454 Bedienungsanleitung

ATD Tools

ATD Tools Atd-5825 Bedienungsanleitung

ATD Tools

ATD Tools ATD-5723 Bedienungsanleitung

ATD Tools

ATD Tools ATD-12555 Bedienungsanleitung

ATD Tools

ATD Tools ATD-109 Bedienungsanleitung

ATD Tools

ATD Tools ATD-12500A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7453A Bedienungsanleitung

ATD Tools

ATD Tools ATD-8401 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7458 Bedienungsanleitung

ATD Tools

ATD Tools ATD-5666 Bedienungsanleitung

ATD Tools

ATD Tools ATD-2102 Bedienungsanleitung

ATD Tools

ATD Tools ATD-10531 Bedienungsanleitung

ATD Tools

ATD Tools ATD-3736 Gebrauchs- und Pflegehandbuch

ATD Tools

ATD Tools ATD-10515 Gebrauchs- und Pflegehandbuch

ATD Tools

ATD Tools ATD-5165 Bedienungsanleitung

ATD Tools

ATD Tools 7452 Gebrauchsanweisung

ATD Tools

ATD Tools ATD-12555 Bedienungsanleitung

ATD Tools

ATD Tools ATD-12549 Bedienungsanleitung

ATD Tools

ATD Tools ATD-3737 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7463 Bedienungsanleitung

ATD Tools

ATD Tools ATD-7454A Bedienungsanleitung

ATD Tools

ATD Tools ATD-7456 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch