ATEN VK1200 Bedienungsanleitung
ATEN Control System
User Manual
www.aten.com
Setup Guide
ATEN VanCryst™
VK1200 / VK2200
Control Box Gen.2
VK1200 / VK2200 Setup Guide
ii
Compliance Statements
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
The device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
Warning
Operation of this equipment in a residential environment could cause radio
interference.
Achtung
Der Gebrauch dieses Geräts in Wohnumgebung kann Funkstörungen
verursachen.
KCC Statement:
Industry Canada Statement
This Class A digital apparatus complies with Canadian ICES-003.
VK1200 / VK2200 Setup Guide
iii
RoHS
This product is RoHS compliant.
Contents
1. Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overall Installation Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2. Getting Started
Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rack Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Desktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Powering the VK1200 / VK2200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3. Initialization
ID, Network & License Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting Controller ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Determining the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Changing Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. Wiring
Wiring and Connecting to Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
12 V DC Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Digital I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Bidirectional Serial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RS-232 (3-Pin). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RS-232/422/485 (5-Pin). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Unidirectional IR / Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
IR Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Serial Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Control LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5. ATEN Configurator
ATEN Configurator — VK6000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
VK1200 / VK2200 Setup Guide
1
Overview
The VK1200 / VK2200 Control Box is an Ethernet-based controller device that
connects and integrates a spate of devices to provide single-access
configuration and convenient remote control for a room setting, such as
boardrooms and lecture halls.
It offers multiple bidirectional serial ports, relays, IR/serial ports, digital I/O,
and 12 V DC power output ports, as well as a dedicated control LAN port,
separate from the corporate LAN, for IP device management within a secure
subnetwork. In addition, it also supports a range of ATEN Expansion Boxes in
providing versatile scalability.
Once successfully connected, users will be able to configure all in-room
devices using the ATEN Configurator software — VK6000, and allow remote
control using ATEN Touch Panel, ATEN Keypads, and Android / iOS /
Windows mobile devices via the ATEN Control System app.
For a centralized management, the VK1200 / VK2200 can be connected to
ATEN Unizon, a global AV management platform software, allowing users to
control and monitor multiple ATEN Ethernet-based solutions across different
locations, including but not limited to ATEN Control Boxes, at the same time.
Package Contents
Make sure the following are present and in working condition:
1 VK1200 / VK2200 Control Box Gen. 2
1 power cord
1 foot pad set (4 pcs)
1 rack mount kit (VK2200 only)
1 user instructions
1 terminal block kit
Terminal Block VK1200 VK2200
2-Pin 7 20
3-Pin 2 6
5-Pin 1 4
Overview
2
Before You Start
The following is a checklist of the items to prepare / consider before you start:
Go through the numbers and types of ports available, and see if it satisfies
all of the devices you want to be controlled within your room setting.
Note: For more control port interfaces, up to 8 ATEN Expansion boxes per
expander model can be connected to the VK1200 / VK2200. See Compat-
ible Products on the product web page for details.
Consider the recommended maximum length of each interface cable, as
listed below, and choose an appropriate installation location for the
VK1200 / VK2200.
Note: The maximum allowed length of each interface cable may vary de-
pending on the cable quality.
Interface VK1200 VK2200
Bidirectional
RS232/422/485
Serial
3-Pin RS-232 1 6
5-Pin
RS-232/422/485 12
Unidirectional IR/Serial 2 8
Relay 4 8
Digital I/O 2 8
12 V DC Output 1 4
Ethernet 2 2
Interface Length (m)
RS-232 15
RS-422/485 350
Relay 30
I/O 30
IR 30
VK1200 / VK2200 Setup Guide
3
Prepare a PC with the following specifications, which may be used to set
the system settings of the VK1200 / VK2200 and run VK6000.
Windows 7 / 8 / 8.1 / 10
Installed with .Net Framework V4.5 or later
Take note of the network information and login credentials of each IP
device that will be connecting to and managed by the VK1200 / VK2200,
if any.
Front Panel
VK1200
VK2200
No. Component Description
1 relay LEDs
Lights green to indicate an active device connection or
signals being transmitted.
Blinks green once to indicate system startup, with the
buzzer beeping once
2I/O LEDs
3 IR / serial LEDs
4 serial LEDs
1
2
35
6
78
4
9121110
1
12
5
24
3689
710 11
Overview
4
5LAN LED Lights green to indicate successful connection to the
network.
6 Control LAN LED
7DC output
overload LED
Lights orange to indicate DC output exceeding the
maximum output threshold, with the buzzer beeping for 3
seconds.
Note: Please unplug any of the connected devices to keep
its total output under 12 V DC, 1 A / 2A for VK1200 /
VK2200 and restart the controller unit.
8 IR receiver / LED Passes the functions of a remote control to the VK1200 /
VK2200 in learning mode. The distance between the IR
remote and the receiver window should be kept under 10
cm with a direct line of sight.
The LED blinks green to indicate the unit is receiving
signals from an IR remote control
The LED lights green to indicate entering learning
mode, or IR learning success with the buzzer beeping
once.
9 USB port / LED Plugs in a USB device to upload Viewers (configured by
the VK6000) to the VK1200 / VK2200.
The LED blinks green to indicate that Viewers are being
uploaded, and lights green to indicate a successful
upload, with the buzzer beeping once upon USB plug-in
and once upon upload success.
The LED lights orange to indicate upload failure, with
the buzzer beeping 3 times for no available file found or
upload failure.
10 reset button
Clear all settings but network: Press and hold until
the front panel LEDs blink once, with the buzzer
beeping once (about 8 seconds). The LEDs and
buzzer will trigger once more when the reset is
complete.
Reset network settings: Short press once.
Note: For more reset functions, please refer to the user
manual.
11 LCD panel and
buttons
Use the Up, Down, and Enter buttons to display the unit’s
system information, and set its controller ID.
12 power LED Lights green when the unit is turned on.
No. Component Description
VK1200 / VK2200 Setup Guide
5
Rear Panel
VK1200
VK2200
No. Component Description
1 power socket Plugs in the power cord from an AC power source.
2 power switch Powers the unit on or off.
3 12 V DC output ports 1 / 4 DC output port(s) providing a total output of 12 V
DC, 1 / 2 A from the VK1200 / VK2200.
4 relay channels 4 / 8 channels; normally open, isolated relays with a
contact rating of 24 V DC, 2 A max.
5 I/O channels 2 / 8 channels that can be configured as digital inputs
or outputs, with the first pin being ground and the rest
being number pins.
Digital Input:
VDC Mode: 0 - 24 V DC; programmable range
of 1 - 24 V DC
Dry Contact Mode: Pull-up 2k Ω to +12 V DC
Digital Output: 300 mA sink from 24 V DC
1 2 3 4 5 106
11
78 9
11 1 2 3456 10
89
7
Overview
6
6 IR / serial ports 2 / 8 IR ports that can also be configured as RS-232
TX ports. pin 1: Signal / pin 2: Ground.
7 RS-232/422/485
serial ports
1 / 2 5-pin RS-232/422/485 serial ports by pin
assignment.
8 RS-232 serial ports 1 / 6 3-pin RS-232 serial ports with Tx, Rx and GND.
9 Control LAN Connects the unit to a
secure subnetwork,
separate from the corporate
LAN, for managing IP
devices and configuration
by the ATEN Configurator
VK6000, as well as for
remote control by ATEN
Keypads, Touch Panel or
the ATEN Control System
app on mobile devices.
Default network settings
when no dynamic IP
address is assigned, by
a DHCP server, after 30
seconds:
IP: 192.168.0.60 / mask:
255.255.255.0
10 LAN
Connects the unit to the
corporate LAN for remote
access and centralized
management by ATEN
Unizon.
Default network settings
when no dynamic IP
address is assigned, by
a DHCP server, after 30
seconds:
IP: 192.168.1.60 / mask:
255.255.255.0
11 grounding terminal Connects to the grounding wire.
No. Component Description
VK1200 / VK2200 Setup Guide
7
Overall Installation Procedure
The installation of the VK1200 / VK2200 shall be done in the following order:
Step 1 — Mounting the VK1200 / VK2200
see Placement, page 8.
Step 2 — Powering the VK1200 / VK2200
see Powering the VK1200 / VK2200, page 11.
Step 3 — Controller ID Setting and Initilization
see ID, Network & License Configuration, page 12.
Step 4 — Wiring and Connecting Devices
see Wiring and Connecting to Devices, page 16.
Step 5 — Adding the VK1200 / VK2200 on VK6000
see ATEN Configurator — VK6000, page 27.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ATEN Netzwerk-Hardware Handbücher
ATEN
ATEN VE44PB Bedienungsanleitung
ATEN
ATEN SN0108CO Bedienungsanleitung
ATEN
ATEN UC9020 StreamLIVE HD Bedienungsanleitung
ATEN
ATEN PE7216 Bedienungsanleitung
ATEN
ATEN UH-152 Bedienungsanleitung
ATEN
ATEN Slideaway CL1008 Bedienungsanleitung
ATEN
ATEN Altusen SN0100 Series Bedienungsanleitung
ATEN
ATEN CL1308 Bedienungsanleitung
ATEN
ATEN SN0108A Bedienungsanleitung
ATEN
ATEN CS231 Bedienungsanleitung
Beliebte Netzwerk-Hardware Handbücher anderer Marken
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung
Yudor
Yudor YDS-16 Bedienungsanleitung
D-Link
D-Link ShareCenter DNS-320L Bedienungsanleitung
Samsung
Samsung ES1642dc Gebrauchsanweisung
Honeywell Home
Honeywell Home LTEM-PV Montageanleitung
