ATEN Master View CS-72A Bedienungsanleitung

User Manual

CS-72A

Read this guide thoroughly and follow the installation and operation

procedures carefully in order to prevent any damage to the unit and/or

any devices that connect to it.

This package contains:

M1 Master View CS-72A KVM Switch

M2 CS Custom KVM Cables

M1 Console Adapter Cable

M1 User Manual

M1 Quick Start Guide

If anything is damaged or missing, contact your dealer.

Manual Part No. PAPE-1224-1AT

Printed in Taiwan 02/2003

2003-02-18

Note: This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy, and if not installed and

used in accordance with the instruction manual,may cause

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

MReorient or relocate the receiving antenna;

MIncrease the separation between the equipment and

receiver;

MConnect the equipment into an outlet on a circuit different

from that which the receiver is connected;

MConsult the dealer or an experienced radio/television

technician for help.

2003-02-18

Overview

The CS-72A KVM (Keyboard, Video, Mouse), Switch is a

control unit that allows the control of two computers from a

single console (keyboard, monitor, and mouse). With its custom

designed connectors, the CS-72A reduces the number of ports

required for a 2 Port KVM switch from 9 (6 PS/2 and 3 HDB) to

only 3 (2 custom designed SPDB-15 female connectors for the

computer attachments, and a single, integrated, custom

designed SPDB-15 male connector for the keyboard, video,

and mouse).

The special connector design provides several advantages

over standard KVM switch implementations: 1) increased

reliability; 2) a handsome, space-saving, vertical-standing,

modern appearance; 3) neater, more efficient, cabling that

eliminates the usual tangled mess.

Setup is fast and easy; plugging cables into their appropriate

ports is all that is entailed. There is no software to configure, so

there is no need to get involved in complex installation routines

or be concerned with incompatibility problems. Since the

CS-72A intercepts keyboard and mouse input directly, it works

on any hardware platform and with all operating systems.

The CS-72A provides two convenient methods to access the

computers: 1) toggling the KVM focus from one computer to the

next by pressing the push button port selection switches

located on the unit’s front panel; and switching directly to the

target computer by entering Hotkey combinations from the

keyboard.

There is no better way to save time and money than with an

CS-72A installation. By allowing a single console to manage

both computers, the CS-72A eliminates the expense of

purchasing a separate keyboard, monitor, and mouse for each

one. Additionally, it saves the extra space and energy costs

that they would require, and eliminates the inconvenience and

wasted effort involved in constantly having to move from one

computer to the other.

- 1 -

2003-02-18

Features

MCompact Vertical-Standing Design

MCustom Connector Layout Requires Only 3 Ports - 2

SPDB-15 Female Connectors for Connecting to the

Computers - Plus A Single, Integrated, SPDB-15 Male

Connector For the Keyboard, Video, and Mouse Console

MEasy to Install - No Software Required - Connecting Cables

to the Computers Is All It Takes

MEasy to Operate - Computer Selection Via Selection

Switches or Hotkeys

MPower On Detection - Automatically Switches to the First

Powered On Port - Automatically Switches to the Next

Powered On Port If the Current One is Shut Down

MAuto Scan Function to Monitor Computer Operation

MLED Display For Easy Status Monitoring

MHot Pluggable - Add or Remove Computers Without

Powering Down the Switch

MCaps Lock, Num Lock, and Scroll Lock States are Saved

and Restored When Switching

MKeyboard and Mouse Emulation for Error Free Computer

Booting

MSupports Microsoft IntelliMouse and the Scrolling Wheel on

Most Mice

MSuperior Video Quality - Up To 2048 x 1536; DDC, DDC2,

DDC2B

MNon-powered

MSaves Time, Space, Power, and Equipment Costs

- 2 -

2003-02-18

System Requirements

Console

MA VGA, SVGA, or Multisync monitor capable of the highest

resolution that you will be using on any computer in the

installation

MA PS/2 style keyboard

MA PS/2 style mouse

Computers

The following equipment must be installed on each computer

that is to be connected to the system:

MA VGA, SVGA or Multisync port.

MA 6-pin mini-DIN (PS/2 Style) mouse port.

MEither a 6-pin mini-DIN (PS/2 Style) keyboard port with

+5V DC on pin 4 and Ground on pin 3, or a 5-pin DIN (AT

Style) keyboard port with +5V DC on pin 5 and ground on

pin 4.

- 3 -

2003-02-18

Cables

Only CS Custom cable sets specifically designed to work with

this switch may be used. One Console Connector Cable and

two 1.2m KVM cable sets are provided with this package. KVM

cable sets are also available in 1.8 and 3 m lengths. If you

need additional cables, contact your dealer.

Note: 1. If your computer uses a standard AT style keyboard

socket, you will need a PS/2-to-AT keyboard adapter

(Part No. 2A-106 or any standard keyboard adapter),

in order to plug the cable into the Computer’s

keyboard port.

2. The CS-72A only supports PS/2 style mice - it does

not support serial mice.

- 4 -

2003-02-18

Components

Front View:

1. Port Selection Switches

MPress a switch to give the KVM focus to the system

attached to its corresponding port.

MPressing Buttons 1 and 2 simultaneously for 3 seconds

starts Auto Scan Mode (see p. 10).

MWhile in Auto Scan Mode, pressing either button exits

Auto Scan Mode and switches the KVM focus to its

corresponding port.

2. Port LEDs

The Port LEDs are built into the Port Selection Switches. A lit

LED indicates that its corresponding Port is the one that has

the KVM focus.

Depending on the Port’s status, the LED may flash

according to a specific pattern (see the table on p. 10 for

details).

- 5 -

1 & 2

2003-02-18

Rear / Bottom View

1. CPU Port Connectors*

The KVM cables that connect the unit to the mouse,

keyboard, and video ports on the computers you are

connecting up can plug into any available port.

2. Console Port Connector*

The Console Adapter Cable plugs in here.

*The shape of the 15-pin CPU and Console port connectors

has been specifically modified so that only cables designed to

work with this switch can plug in (see the Cables section on

p. 4 for details).

3. Power Jack

The power adapter plugs into this jack located on the

CS-72A’s bottom panel.

Note: The CS-72A does not require external power. Use of

a power adapter is optional, and requires a separate

purchase.

- 6 -

2003-02-18

Installation

The CS-72A can either lay flat on the desktop or stand upright.

To have it stand upright, unsnap its mounting stand from the

bottom of the unit; turn it 90o; and snap it back into place. See

the photo on the front page for an example.

Refer to the diagram on p. 8 as you do the following:

1. Plug the Console Adapter Cable into the Console Port

Connector on the rear panel of the CS-72A.

2. Plug your keyboard, monitor and mouse into their respective

connectors of the Console Adapter Cable. Each connector is

marked with an approprieate icon to indicate itself.

3. Use the custom KVM cables (described in the Cables

section on p. 4), to connect the CS-72A CPU Ports to the

monitor, keyboard and mouse ports of the computers you

are installing.

Note: If your computers use AT style connectors for the

keyboard, refer back to the note in the Cables section

on p. 4.

4. If you choose to use external power, plug the power adapter

into an AC power source, then plug the power adapter cable

into the unit’s Power Jack. See the note on the next page for

informaton about the adapter.

5. Turn on the power to the computers.

Note: The CS-72A’s default is to link to the first computer

you turn on.

- 7 -

1. Before you begin, make sure that power to all

the devices you will be connecting up have been

turned off. You must unplug the power cords of

any computers that have the Keyboard Power

On function.

2. To prevent damage to your installation due to

ground potential difference, make sure that all

devices on the installation are properly grounded.

2003-02-18

Note: 1. In order to fit into the jack, the power adapter cable

should have an Lshaped plug.

2. The power adapter should be DC9V with the inside

positive and the outside negative:

- 8 -

2003-02-18

Inhaltsverzeichnis

Andere ATEN Schalten Handbücher

ATEN

ATEN KH1508Ai Bedienungsanleitung

ATEN

ATEN CS1798 Bedienungsanleitung

ATEN

ATEN ALTUSEN KH1508I Bedienungsanleitung

ATEN

ATEN Slideaway CL5708 Bedienungsanleitung

ATEN

ATEN Altusen KL1508Ai Bedienungsanleitung

ATEN

ATEN CS62T Bedienungsanleitung

ATEN

ATEN Slideaway CL5708 Bedienungsanleitung

ATEN

ATEN CS62KM Bedienungsanleitung

ATEN

ATEN MASTER VIEW CS-124U Bedienungsanleitung

ATEN

ATEN Multi-View KVMP Switch Bedienungsanleitung

ATEN

ATEN Altusen KM0032 Bedienungsanleitung

ATEN

ATEN ALTUSEN KH1508I Bedienerhandbuch

ATEN

ATEN Master View ACS-1602 Bedienungsanleitung

ATEN

ATEN VS0801H Bedienungsanleitung

ATEN

ATEN VS0801HB Bedienungsanleitung

ATEN

ATEN CS1732B Bedienungsanleitung

ATEN

ATEN Master View CS-1754 Bedienungsanleitung

ATEN

ATEN CS1644a Bedienungsanleitung

ATEN

ATEN VM0404 Bedienungsanleitung

ATEN

ATEN CS1922M Bedienungsanleitung

ATEN

ATEN CN8000A Bedienungsanleitung

ATEN

ATEN Video DynaSync Installationsanleitung

ATEN

ATEN CS1768 Bedienungsanleitung

ATEN

ATEN KN8100V Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung