Atlas Copco SmartHEAD Bedienungsanleitung

smartHEAD Installation Guide

1 (4) 9836 4569 01 Revision 4

smartHEAD INSTALLATION GUIDE

Index:

INSTALLING THE smartHEAD on the STwrench.................................................................................2

INSTALLING THE smartHEAD on the MRTT-C...................................................................................3

GENERAL

The smartHEAD, to be installed on the STwrench and MRTT-C,

defines the wrench capacity. You can install or change the smartHEAD

without the need of any further settings or calibration: the STwrench

and STanalyser loads automatically the transducer data at the power

on.

PACKAGE

Refer to the check list included for the package list.

SAFETY

Warning: Read the STwrench Product Instruction (No. 9836 4489 00) and MRTT-C User Guide (No.

9836 5984 01) before installing and using the product.

HANDLING

The module is electrostatic sensitive device; DO NOT touch any electrical contact to avoid risk of

module damages.

If possible, before handling any STwrench modules, touch with your hand a big metallic object,

in order to avoid electrostatic discharges while handling the modules.

Observe the following precautions to handle the module:

Correct handling: NOT correct handling:

smartHEAD Installation Guide

2 (4) 9836 4569 01 Revision 4

INSTALLING THE smartHEAD on the STwrench

1. SWITCH OFF THE STwrench.

2. INSERT THE smartHEAD IN THE WRENCH CONTROLLER AND TIGHTEN THE LOCKING NUT UNTIL

WHEN THE “CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the wrench controller. The guide and

the reference pin must be inserted in the relative housings; do not force them in other position.

3. TURN ON THE STwrench

4. IF THE FOLLOWING MESSAGE IS SHOWN, CHECK THE DATE AND SELECT YES TO CONTINUE

AND USE THE smartHEAD (the first use date is set at the date shown):

Guide

Reference PIN

Locking nut

smartHEAD

smartHEAD Capacity Indication

STwrench

smartHEAD Installation Guide

3 (4) 9836 4569 01 Revision 4

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STwrench power on.

5. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE FOLLOWING MESSAGE IS SHOWN:

NOTE: each smartHEAD is intended to be associated to a single STwrench controller!

The smartHEAD interchangeability assures easy and fast maintenance operations and wrench

upgrade. IMPORTANT NOTE:

Assembling different heads on the same controller during the normal wrench operations is an

improper use of the modularity concept, and will invalidate the warranty on the wrench

components.

The smartHEAD should be left always connected to the controller. For example, do not

disassemble it at the end of the day of for wrench transportation.

INSTALLING THE smartHEAD on the MRTT-C

6. DISCONNECT THE MRTT-C FROM THE STanalyser / STa 6000.

Locking nut

smartHEA

MRTT

Date

smartHEAD Installation Guide

4 (4) 9836 4569 01 Revision 4

7. INSERT THE smartHEAD IN THE MRTT-C AND TIGHTEN THE LOCKING NUT UNTIL WHEN THE

“CLICK” IS HEARD

NOTE: there is only one way to insert the smartHEAD into the MRTT-C. The guide and the

reference pin must be inserted in the relative housings; do not force them in other position.

8. CONNECT THE MRTT-C TO THE STanalyser / STa 6000 AND TURN ON THE STanalyser / STa 6000

9. IF THE FOLLOWING MESSAGE IS SHOWN ON STa 6000, CHECK THE DATE AND SELECT YES TO

CONTINUE AND USE THE smartHEAD (the first use date is set at the STa 6000 date):

Selecting No the first date is not set, but the smartHEAD is blocked. The messsage above is

shown again at the next STa 6000 power on.

10. IF THE smartHEAD IS NOT PROPERLY INSTALLED THE Transducer Error MESSAGE IS SHOWN.

NOTE: each smartHEAD is intended to be associated to a single MRTT-C!

The smartHEAD interchangeability assures easy and fast maintenance operations and system

upgrade. IMPORTANT NOTE:

Assembling different heads on the same MRTT-C during the normal operations is an improper

use of the modularity concept, and will invalidate the warranty on the wrench components.

The smartHEAD should be left always connected to the MRTT-C. For example, do not

disassemble it at the end of the day of for transportation.

Guide

Reference PIN

Date / time

Inhaltsverzeichnis

Andere Atlas Copco Elektrowerkzeuge Handbücher

Atlas Copco

Atlas Copco LMS68 GOR25 Merkblatt

Atlas Copco

Atlas Copco EP8PTI70 HR10-MT Merkblatt

Atlas Copco

Atlas Copco Cobra Combi Wartungs- und Serviceanleitung

Atlas Copco

Atlas Copco EP7PTI55 HR10-MT Merkblatt

Atlas Copco

Atlas Copco ITB-A31-05-I06 Originalbetriebsanleitung

Atlas Copco

Atlas Copco P2505 Merkblatt

Atlas Copco

Atlas Copco ETDST101-150-20-T40F Originalbetriebsanleitung

Atlas Copco

Atlas Copco ETV ST81-150-HAD Originalbetriebsanleitung

Atlas Copco

Atlas Copco ETP SRB81-300-20-D Originalbetriebsanleitung

Atlas Copco

Atlas Copco SR21-30-FS Originalbetriebsanleitung

Atlas Copco

Atlas Copco RTX-8 Bedienungsanleitung

Atlas Copco

Atlas Copco RT-3 Bedienungsanleitung

Atlas Copco

Atlas Copco ETD-STR61-120-13-T25 Merkblatt

Atlas Copco

Atlas Copco EBL35 Originalbetriebsanleitung

Atlas Copco

Atlas Copco ETV STB34-30-10-B Merkblatt

Atlas Copco

Atlas Copco RT-25 Bedienungsanleitung

Atlas Copco

Atlas Copco EBL20-RE Bedienungsanleitung

Atlas Copco

Atlas Copco LH 11 Bedienungsanleitung

Atlas Copco

Atlas Copco W2611 Merkblatt

Atlas Copco

Atlas Copco ETP STB34-06-10 Originalbetriebsanleitung

Atlas Copco

Atlas Copco PRO W2630 Bedienungsanleitung

Atlas Copco

Atlas Copco RTX-18 Bedienungsanleitung

Atlas Copco

Atlas Copco ETP SRB31-20-I06-BD Originalbetriebsanleitung

Atlas Copco

Atlas Copco LTP51 H Series Merkblatt

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Atlas Copco smartHEAD Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken