Atlas Equipment 12ASL Bedienungsanleitung
Replace This With Cover PDF
Revised: 01/28/2020
Read this entire manual before operation begins.
Record below the following information which is located on the serial number
data plate.
Serial No.
Model No.
Date of Installation
Contents
General Information. . . . . . . . . . 5
Product Identification . . . . . . . . . 8
Packing, Transport, Storage . . . . . . 10
Product Description . . . . . . . . . . 12
Technical Specification. . . . . . . . . 14
Safety . . . . . . . . . . . . . . . . 22
Installation . . . . . . . . . . . . . . 26
Operation And Use . . . . . . . . . . 36
Maintenance . . . . . . . . . . . . . 43
Troubleshooting. . . . . . . . . . . . 45
Parts List . . . . . . . . . . . . . . . 48
Warranty . . . . . . . . . . . . . . . 71
4
12ASL
PRINTING CHARACTERS AND SYMBOLS
Throughout this manual, the following symbols and printing characters are used
to facilitate reading:
Indicates the operations which need proper care
Indicates prohibition
Indicates a possibility of danger for the operators
Indicates the direction of access for motor vehicles to the lift
BOLD
TYPE Important information
WARNING: before operating the lift and carrying out any
adjustments, read chapter 7 “installation” where all proper
operations for a better functioning lift are shown.
General Information 5
12ASL
General Information
This chapter contains warning instructions to operate the lift properly and
prevent injury to operators or objects.
This manual has been written to be used by shop technicians in charge of the lift
(operator) and routine maintenance (maintenance operator).
The operating instructions are considered to be an integral part of the lift and
must remain with it for its whole useful life.
Read every section of this manual carefully before operating the lift and
unpacking it since it gives helpful information about:
• Safety Of People
• Safety Of The Lift
• Safety Of Lifted Vehicles
The company is not liable for possible problems, damage, accidents, etc.
resulting from failure to follow the instructions contained in this manual.
Only skilled technicians of AUTHORIZED DEALERS or SERVICE CENTERS
AUTHORIZED by the manufacturer shall be allowed to carry out lifting, transport,
assembling, installation, adjustment, calibration, settings, extraordinary
maintenance, repairs, overhauling and dismantling of the lift.
THE MANUFACTURER IS NOT RESPONSIBLE FOR POSSIBLE DAMAGE TO
PEOPLE, VEHICLES OR OBJECTS IF SAID OPERATIONS ARE CARRIED OUT
BY UNAUTHORIZED PERSONNEL OR THE LIFT IS IMPROPERLY USED.
Any use of the machine made by operators who are not familiar with the
instructions and procedures contained herein shall be forbidden.
General Information 6
12ASL
1.1 Manual Keeping
For proper use of this manual, the following is recommended:
• Keep the manual near the lift, in an easily accessible place.
• Keep the manual in an area protected from moisture.
• Use this manual properly without damaging it.
• Any use of the machine made by operators who are not familiar with the
instructions and procedures contained herein shall be forbidden.
This manual is an integral part of the lift: it shall be given to the new owner if
and when the lift is resold.
1.2 Obligation In Case Of Malfunction
In case of machine malfunction, follow the instructions
contained in the following chapters.
1.3 Cautions For The Safety Of The Operator
Operators must not be under the influence of sedatives, drugs or alcohol when
operating the machine.
Before operating the lift, operators must be familiar with
the position and function of all controls, as well as with the
machine features shown in the chapter “Operation and use”
General Information 7
12ASL
1.4 Warnings
Unauthorized changes and/or modifications to the machine
relieve the manufacturer of any liability for possible damages to
objects or people. Do not remove or make inoperative the safety
devices, this would cause a violation of safety at work laws and
regulations.
Any other use which differs from that provided for by the
manufacturer of the machine is strictly forbidden.
The use of non genuine parts may cause damage to people or
objects
1.5 Scrapping
When your machine’s working life is over and it can no longer be used, it must
be made inoperative by removing any connection to power sources. These
units are considered as special waste material, and should be broken down into
uniform parts and disposed of in compliance with current laws and regulations. If
the packing are not polluting or non-biodegradable, deliver them to appropriate
handling station.
DECLARATION OF WARRANTY
AND LIMITATION OF LIABILITY
The manufacturer has paid proper attention to the preparation of this manual.
However, nothing contained herein modifies or alters, in any way, the terms
and conditions of manufacturer agreement by which this lift was acquired, nor
increase, in any way, manufacturer’s liability to the customer.
TO THE READER
Every effort has been made to ensure that the information contained in this
manual is correct, complete and up-to date. The manufacturer is not liable for
any mistakes made when drawing up this manual and reserves the right to make
any changes due the development of the product, at any time.
Product Identification 8
12ASL
Product Identification
The identification data of the machine are shown in the label placed on the
control unit.
LOGO
Type: ……………
Model: ……………
Serial Number: ……………
Year of manufacturing: ……………
Capacity: ……………
Voltage: ……………
Power: ……………
Use the above data both to order spare parts and when getting
in touch with the manufacturer (inquiry). The removal of this
label is strictly forbidden.
Machines may be updated or slightly modified from an aesthetic point of view
and, as a consequence, they may present different features from these shown,
this without prejudicing what has been described herein.
2.1 Warranty Certificate
The warranty is valid for a period of 2 years on structural components, 1 year
on hydraulic components and 90 days on wear parts starting from the date
of purchase. This warranty does not include labor or shipping. The warranty
consists of parts only. The warranty will come immediately to an end when
unauthorized modifications, faulty assembly and improper use to the lift or parts
of it are carried out. The presence of defects in workmanship must be verified by
Greg Smith Equipment Sales.
Product Identification 9
12ASL
2.2 Technical Servicing
For all servicing and maintenance operations not specified or shown in these
instructions, contact your Dealer where the machine has been bought or the
Manufacturer’s Commercial Department.
Only skilled personnel who are familiar with the lift and this manual shall
be allowed to carry out packing, lifting, handling, transport and unpacking
operations.
Packing, Transport, Storage 10
12ASL
Packing, Transport, Storage
3.1 Packing
The packing of the lift is delivered in following components:
• No. 2 base units, each one with a runway equipped with 2 hydraulic
cylinders.
• No. 1 rolling jack with an air/hydraulic pump.
• No. 1 control unit and containing hydraulic unit, hydraulic hoses, air hoses,
anchor bolts, rubber blocks and the technical files.
• No. 2 turntable recess covers.
• No. 2 drive-on ramps, 2 front wheel stops and 4 hose protective covers if
the lift is ordered for on-floor installation.
(If requested, optional accessories are available to satisfy each customer’s
requirements).
3.2 Lifting And Handling
When loading/unloading or transporting the equipment to the site, be sure to
use suitable loading (e.g. cranes, trucks) and hoisting means. Be sure to hoist
and transport the components securely so that they cannot drop, taking into
consideration the package’s size, weight and center of gravity and it’s fragile
parts.
Hoist and handle only one package at a time.
Inhaltsverzeichnis
Andere Atlas Equipment Scherenhebebühne Handbücher
