Atlas F6-MF Bedienungsanleitung

– 9 – AtlasSound.com

Specifications are subject to change without notice.

Owner’s Manual F6-MF

Multi-Impedance Modular Amplifier

1601 Jack McKay Blvd. • Ennis,Texas 75119 U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

FM250-4 and FM250-70 Module Features

1. Module Status Indicators

Note: They also parallel Status LED on the front panel of the F6-MF panel.

Ready This LED will illuminate Green when an FM250 power module is installed on the appropriate channel and the F6-MF is

turned on.

Signal The channel Signal LED will illuminate Green when the FM250 amplifier output signal produces a minimum 1 Watt

output.

Limit The Limit LED will illuminate Yellow under load conditions. If the FM250 function switch is set to Limit then the LED

acts as a maximum level indicator. If the FM250 channel Limit function is off, the LED reacts as a Clip indicator. Also,

under Low Impedance loads, this LED serves as a current Limit indictor.

Protect The Protect LED will illuminate Red during one the following conditions. No output will occur while this LED is

illuminated. It will reset itself after the condition has been corrected.

1) Shorted speaker output.

2) Thermal Shut Off. The Temp F6-MF TEMP LED will also be illuminated.

3) Current Overdrive. If the amplifier channel is driving too low of a speaker load.

2. Speaker Connections

A removable Phoenix/Euro Block type connector is supplied to connect your speakers to the FM250 amplifier module. It is

recommended to use 16-gauge wire or lower for connection to the speakers. Note: Do not overload the amp by connecting too many

speakers to the amp.

Protect

Limit

Signal

Ready

Speaker Output

Class 2 Wiring

4Ω

FM250 - 4

250W @ 4Ω

Protect

Limit

Signal

Ready

Speaker Output

Class 2 Wiring

70V

FM250 -70

250W @ 70V

AtlasSound.com – 10 –

Specifications are subject to change without notice.

Owner’s Manual

F6-MF

Multi-Impedance Modular Amplifier

1601 Jack McKay Blvd. • Ennis,Texas 75119 U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

FM250-4 & FM250-70 Function Switch

FM250 Module Dip Switch Functions are located near the rear of the FM250 modules. Note: It is essential to preset your setting prior

to inserting the module into the F6-MF.

Factory Dip Switch Presets

Dip Switch 1 ships in the “On” position. Dip Switches 2 & 3 ship in the “Off” position.

Dip Switch 1, Gain

When placed in the “On” position the channel’s Gain or Input Sensitivity will be 1V (0dBV) for rated output. When placed in the “Off”

position the Gain is set to 2V (6dBV).

Dip Switches 2 & 3, HPF

The High Pass Filter (HPF) when placed into the “On” position engages a 100Hz / 12dB filter. When in the “Off” position the module

operates at full audio bandwidth.

– 11 – AtlasSound.com

Specifications are subject to change without notice.

Owner’s Manual F6-MF

Multi-Impedance Modular Amplifier

1601 Jack McKay Blvd. • Ennis,Texas 75119 U.S.A.

Telephone: 800.876.3333 • Fax: 800.765.3435

FM250 Ampliﬁer Module Installation

Use the following steps and read all steps prior to installation.

1. Turn F6-MF AC Power Switch to the “Off” position.

2. Turn down all level controls on the front panel.

3. Remove the blank card slot cover. Do not discard the two screws, you will need them later.

4. Set the function switches on the FM250 module. (See Page 10)

5. Carefully and slowly guide the module into the slot with the PCB components facing to the right. Note: The module heatsink

top and bottom metal edge mate with the mainframe plastic card guides. Do not force the card. Realign if necessary.

6. After the module is pushed in and in contact with the back plane of the PCB assembly mating connector, firmly press the

module in completing the connection. If the module plate is flush to the F6-MF, the module is fully seated.

7. Insert the two screws from the cover pate. Some minor alignment may be required.

Align Modules to

Top & Bottom Card

Guides

Andere Handbücher für F6-MF

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Atlas Verstärker Handbücher

Atlas

Atlas AA400PHD Bedienungsanleitung

Atlas

Atlas F6-MF Bedienungsanleitung

Atlas

Atlas TSD-PA20VG Bedienungsanleitung

Atlas

Atlas PA601 Bedienungsanleitung

Atlas

Atlas PA40G Bedienungsanleitung

Atlas

Atlas MVXA Bedienungsanleitung

Atlas

Atlas STRATEGY AA35 Bedienungsanleitung

Atlas

Atlas AA200PHD Bedienungsanleitung

Atlas

Atlas TSD-PA10VG Bedienungsanleitung

Atlas

Atlas DSP2210 Bedienungsanleitung

Atlas

Atlas TSD-PA252G Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Atlas

Atlas AA120 Bedienungsanleitung

Atlas

Atlas DSP8807 Bedienungsanleitung

Atlas

Atlas AA120 Bedienungsanleitung

Atlas

Atlas CP400 Bedienungsanleitung

Atlas

Atlas TSD-ZDC Bedienungsanleitung

Atlas

Atlas AA200PHD-CE Bedienungsanleitung

Atlas

Atlas STRATEGY AA35 Bedienungsanleitung

Atlas

Atlas AA-SMG Bedienungsanleitung

Atlas

Atlas AA120 Bedienungsanleitung

Atlas

Atlas TSD-ML22VCA Bedienungsanleitung

Atlas

Atlas AA100PHD Bedienungsanleitung

Atlas

Atlas DPA-102PM Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung

Phonic

Phonic XP 3000 Bedienungsanleitung