Atmel AT88SC-DK1 Bedienungsanleitung
AT88SC-DK1 WELCOME AND QUICK START GUIDE
Dear Valued Customer,
Thank you for choosing CryptoMemory®for your security needs. As you may
already know, CryptoMemory provides low-cost powerful security for your product
authentication and secure data storage needs. To ensure you have the most
current information, we ask that you check the CryptoMemory product website at
www.atmel.com/products/SecureMem for any recent updates. We wish you an
exciting development experience and ask that you do not hesitate to contact us at
Best regards,
Your Atmel CryptoMemory Team
Downloaded from Arrow.com.
ÏÏÏÏ
Package Contents
1. 1 AT88SC-DK1 CD
2. 1 CryptoMemory adaptor board
3. 1 tube of CryptoMemory samples
4. 1 Black-Red patch cord
5. 1 Green-Yellow patch cord
ÏÏÏÏ
ADAPTING AT88SC-DK1 TO YOUR DEVELOPMENT SYSTEM
ÏÏÏÏ
System Requirements:
n1 GPIO header pin for TWI clock, SCL.
n1 GPIO header pin for TWI data, SDA.
n1 header pin for power, VCC.
n1 header pin for ground, GND.
ÏÏÏÏ
Software Setup
1. Install contents of AT88SC-DK1 CD into your PC
2. Check the README file for information on CryptoMemory Library Integration and Reference.
AT88SC-DK1 WELCOME AND QUICK START GUIDE Everywhere You Are®
Downloaded from Arrow.com.Downloaded from Arrow.com.
ÏÏÏÏ
Hardware Setup
STEP 1:
Insert a CryptoMemory device into
the SOIC socket
STEP 3:
Connect Clock and Data wires
Align PIN 0 of the SOIC package towards
the header-pins side of the adaptor board.
Use Black-Red patch cord
1. Connect the double-header end of the
Green-Yellow patch cord to the SCL-SDA
header pins of the adaptor board. Align
such that Green connects to SCL and
Yellow connects to SDA.
2. Connect the Green cord to your system
TWI clock.
3. Connect the Yellow cord to your system
TWI data.
Use Green-Yellow patch cord
1. Connect the double-header end of the
Green-Yellow patch cord to the SCL-SDA
header pins of the adaptor board. Align
such that Green connects to SCL and
Yellow connects to SDA.
2. Connect the Green cord to your system
TWI clock.
3. Connect the Yellow cord to your system
TWI data.
STEP 2:
Connect Power and Ground wires
www.atmel.com
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.
ÏÏÏÏ
Troubleshooting
1. Make sure CryptoMemory is properly inserted and aligned in the SOIC socket. The
correct orientation places PIN 0 of the SOIC package towards the adaptor board header
pins. When correctly oriented, holding the adaptor board with header pins towards self
should present the marking texts on the CryptoMemory package right side up.
2. Verify your hardware setup for accurate signal and power connections.
3. Make sure VCC is connected to a high-drive power supply.
4. Make sure your system meets pull-up resistor requirements on signal lines as defined in
CryptoMemory datasheets
5. Make sure to include noise filtering capacitors between Vcc and GND at the device
level, if working with a noisy system.
6. Read and Write CryptoMemory’s Memory Test Zone (MTZ) field to verify connectivity.
MTZ is free of all security requirements at all times.
5253-SMEM-05/07
Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.Downloaded from Arrow.com.
Andere Atmel Sicherheitssystem Handbücher
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung