ATN Thermal Entry Wizard Bedienungsanleitung

ATN ATN

Thermal Entry WizardThermal Entry Wizard

TOUCHLESS FEVER DETECTOR

Quick Start Guide

AMERICAN

TECHNOLOGIES

NETWORK

CORP.

The instructions in this manual are for informational use only and subject to change without notice,

this manual is not to be construed as a commitment by ATN Corp.

ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.

APPEARANCE

USB Interface

35.0 mm

25.3 mm

IR Light

Touch Screen

Card Presenting Area

White Light

Camera Camera

289.98

116.5 mm

46.0 mm

70.0 mm

239.0 mm

Thermographic Module

IR Light

Touch Screen

Card Presenting Area

White Light

Camera Camera

289.98

116.5 mm

46.0 mm

70.0 mm

239.0 mm

Thermographic Module

TAMPER

Wiring

Terminal

Network

Interface PSAM Card Slot (Reserved)

Debugging Port

(for debugging only)

Thermographic

Module

Interface

Power

Interface

NOTE

The figures are for reference only.

INSTALLATION

Installation Environment:

• The device should be at least 2

meters away from the light, and

at least 3 meters away from the

window.

• Make sure the environment illumi-

nation is more than 100 Lux.

• Indoor and windless environment

use only.

Steps:

1. Drill holes on the wall or other sur-

face and install the gang box.

2. Connect the thermographic

module and the main body of the

device. Use 5 supplied screws

(4_KA4×22-SUS) to secure the

mounting plate on the gang box.

1&2

3. Align the device with the mounting plate and hang the device on the

mounting plate. Make sure the two sheets on each side of the mounting

plate have been in the slots at the back of the device.

4. Use 2 supplied screws (SC-M4×14.5TP10-SUS) to secure the device and

the mounting plate.

Direct Sunlight

through Window

Indirect Sunlight

through Window

Backlight

Close to Light

DEVICE WIRING (NORMAL)

• When connecting door magnetic sensor and exit button, the device and

the RS-485 card reader should use the common ground connection.

• The Wiegand terminal here is a Wiegand input terminal. You should

set the face recognition terminal’s Wiegand direction to “Input”. If you

should connect to an access controller, you should set the Wiegand

direction to “Output”. For details, see Setting Wiegand Parameters in

Communication Settings in the user manual.

• The suggested external power supply for door lock is 12 V, 1A.

• The suggested external power supply for Wiegand card reader is 12 V,

1 A.

• Do not wire the device to the electric supply directly.

• When the screw’s head is beneath the device surface, the device is

secured.

• The installation height here is the recommended height. You can

change it according to your actual needs.

• You can also install the device on the wall or other places without the

gang box. For details, refer to the User Manual.

• For easy installation, drill holes on mounting surface according to the

supplied mounting template.

NOTE

Make sure the output of external power supply fulfills LPS.

BTN

Network Interface

Door Contact

(NC)

(COM)

(NO)

DEVICE WIRING

(WITH SECURE DOOR CONTROL UNIT)

NOTE

The secure door control unit should connect to an external power

supply separately. The suggested external power supply is 12 V, 0.5 A.

Exit Bu�on

Power Input

SENSOR

BUTTON

Green/Brown

Black

Green/Black

Black

Lock Output

NC C1

COM

White/Purple

White/Black

White/Red

Red

Black Door Contact

Exit Bu�on

Power

Electric

Dropbolt

Electric

Strike

Sensor Input

Face Recognition Terminal Secure Door Control Unit

Secure Door

Control Unit

Wiring Terminal

ACTIVATION

IMPORTANT NOTE

Please allow the system to run for 30 min after initial boot up, in order

for it to calibrate itself. Once calibration completes the system will pro-

vide accurate temperature measurement.

Power on and wire the network cable after installation. You should activate

the device before the first login.

If the device is not activated yet, it will enter the Activate Device page after

powering on.

Steps:

1. Create a password and confirm the password.

2. Tap Activate to activate the device.

NOTE

For other activation methods, see the device user manual.

CAUTION

Strong password recommended!

We highly recommend you create a strong password of your own

choosing (using a minimum of 8 characters, including upper case let-

ters, lower case letters, numbers, and special characters) in order to

increase the security of your product. And we recommend you reset your

password regularly, especially in the high security system, resetting the

password monthly or weekly can better protect your product.

TEMPERATURE MEASUREMENT

SETTINGS

1. Hold the screen surface and verify the identity to enter the main page.

2. Tap “Temperature” to enter the Temperature Settings page. Configure the

parameters.

• Enable Temperature Detection

When enabling the function, the device will authenticate the permissions

and at the same time take the tempearture. When disabling the device, the

device will authenticate the permissions only.

• Over-Temperature Alarm Threshold

Edit the threshold according to actual situation. If the detected temperature

is higher than the configured one, an alarm will be triggered. By default, the

value is 99.14°F.

• Door Not Open When Detecting Abnormal Termperature

When Enabling the function, the door will not open when the detected tem-

perature is higher than the configured temperature threshold. By default, the

temperature is enabled.

• Temperature Measurement Only

When enabling the function, the device will not authenticate the permis-

sions, but only take the temperature. When disabling the function, the device

will authenticate the permsissions and at the same time take the temperature.

ADDING FACE INFORMATION

1. Hold the screen surface and verify the identity to enter the main page.

2. Enter the User Management page, tap + to enter the Add User page.

3. Set the user parameters according to actual needs.

4. Tap Face and collect the face information according to the instructions.

You can view the captured picture at the upper right corner of the page.

Make sure the face picture is in good quality and size. For details about

the tips and positions when collecting or comparing the face picture, see

the contents on the right.

5. If the picture is in good condition, tap Save to save the picture. Or tap Try

Again to take another face picture.

6. Tap to save the settings. Go back to the initial page to start authenti-

cation. For other authentication methods, see the device user manual.

Use other authentication methods if the device is affected by the light or

other items.

NOTE

Biometric recognition products are not 100% applicable to anti-spoof-

ing environments. If you require a higher security level, use multiple

authentication modes.

TIPS WHEN COLLECTING/

COMPARING FACE PICTURE

Expression

• Keep your expression naturally when collecting or com-

paring face pictures, just like the expression in the picture

on the right.

• Do not wear hat, sunglasses, or other accessories that

can affect the facial recognition function.

• Do not make your hair cover your eyes, ears, etc. and

heavy makeup is not allowed.

POSTURE

In order to get a good quality and accurate face picture, position your face

looking at the camera when collecting or comparing face pictures.

Correct Tilt RaiseSide Bow

• Measurement Area Calibration/Measurement Area Settings

Configure the temperature measurement area and the correction parame-

ters.

SIZE

Make sure your face is in the middle of the collecting window.

Correct Too Close Too Far

POSITIONS WHEN COLLECTING/

COMPARING FACE PICTURE

(Recommended Distance: 0.5 m)

1.4m

0.5m

1.4m

Too High

Too Low

Too Close Too Far

1.4m

1.2m

1.4m

0.5m 0.5m

Recommended Height:

1.43m to 1.90m

Andere Handbücher für Thermal Entry Wizard

Inhaltsverzeichnis

Andere ATN IP-Zugriffskontrollsysteme Handbücher

ATN

ATN X-TRAC 5 Bedienungsanleitung

ATN

ATN X-TRAC Bedienungsanleitung

Beliebte IP-Zugriffskontrollsysteme Handbücher anderer Marken

ZKTeco

ZKTeco SpeedFace-V5L Bedienungsanleitung

2N Access Unit Merkblatt

Kedacom

Kedacom KSCA120 Series Bedienungsanleitung

H3C

H3C WX2880X Bedienungsanleitung

G4S

G4S S870-EX Leitfaden

PRASTEL

PRASTEL M2000PE Bedienungsanleitung

Allegion

Allegion interflex IF-281 Cylinder Bedienungsanleitung

TECOM

TECOM TS1067E Bedienungsanleitung

Fermax

Fermax Memokey 100C Benutzerhandbuch

Fermax

Fermax CITYLINE MEMOKEY Bedienungsanleitung

AKCP

AKCP SP+ Bedienungsanleitung

Bpt

Bpt HNA/102 Bedienungsanleitung

Civintec

Civintec CV9601T-T-1F Bedienungsanleitung

BioMax

BioMax N-X90W Bedienungsanleitung

ZKTeco

ZKTeco OP-200 Bedienungsanleitung

FingerTec

FingerTec s-Kadex Bedienungsanleitung

H3C

H3C WX5002ACCESSCONTROLLER Bedienungsanleitung

C Prox Ltd

C Prox Ltd DPN-2 Bedienungsanleitung