ATN OTS-HD Series Bedienungsanleitung

OTS-HD Series

MANUAL

OTS-HD USER’S GUIDE (REV. 2, DECEMBER, 2016)

AMERICAN

TECHNOLOGIES

NETWORK

CORP.

THERMAL SMART HD

MONOCULARS/VIEWERS

THIS PRODUCT CONTAINS NATURAL RUBBER LATEX WHICH MAY CAUSE ALLERGIC REACTIONS.

CAUTION!

The information in this manual is furnished for informational use only, is subject to change without notice,

is not to be construed as a commitment by ATN Corp.

ATN Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.

POWER

BUTTON

FOCUS

ADJUSTMENT RING

BATTERY

HOUSING CAP

DIOPTER

ADJUSTMENT

RING

MICROSD,

MICRO HDMI

& MICRO USB

START/STOP

VIDEO

RECORDING

ENTER

BUTTON

HAND STRAP

ZOOM IN

LENS CAP

TAKE A

PICTURE

ZOOM OUT

TABLE OF CONTENTS

Features .........................................4

Application .......................................4

Specifications.....................................5

Preparing the device ...............................7

Unpacking .....................................7

Installation of batteries............................7

MicroSD, USB and HDMI ports .....................7

Firmware update ................................8

ON/OFF.......................................9

Using keypad...................................9

Focusing ......................................9

Compass calibration ............................10

Interface ........................................11

Homescreen ..................................11

Main operations................................12

Shortcut carousel ..............................13

Using System menu.............................14

Functions .......................................16

Photo and video modes ..........................16

Rangefinder...................................18

How to perform a NUC...........................20

System Menu ....................................21

Thermal ......................................21

Photo/Video...................................21

Display.......................................21

Settings ......................................22

Servicing ........................................23

Warnings and cautions ..........................23

Mobile Applications ...............................23

FEATURES

RECORD HD VIDEO GPS GEOTAG

WiFi OBSIDIAN USER INTERFACE

SMOOTH ZOOM BLUETOOTH

E-COMPASS 3D GYROSCOPE

SMART RANGE FINDER

APPLICATION

The most technologically advanced line of thermal viewers on the market bar

none! The all new Obsidian “T” II Thermal core beats at the heart of our systems.

More power, more features, smaller packaging, and lower cost have allowed ATN to

make the biggest update to its award winning thermal product line.

Record videos and photos onto a microSD card. Use ATN’s Smart Range Finder

to quickly range in on any object. Smooth Zoom, built in Wi-Fi, Bluetooth, 3D Gyro-

scope, 3D Accelerometer, 3D Magnetometer are but a few of the features and sen-

sors packed into these incredible systems.

SPECIFICATIONS

OTS-HD 384

1.25 - 5x

OTS-HD 384

2 - 8x

OTS-HD 384

4.5 - 18x

OTS-HD 384

9 - 36x

OTS-HD 640

1 - 10x

OTS-HD 640

1.5 - 15x

OTS-HD 640

2.5 - 25x

OTS-HD 640

5 - 50x

Sensor 384×288 640×480

Magniﬁcation 1.25 - 5x 2 – 8× 4.5 – 18× 9 – 36× 1 – 10× 1.5 – 15× 2.5 – 25× 5 – 50×

Angle of view 16×12.5 12×9.5 6×4.7 3×2.4 32×25 24×19 12.5×9.7 6×4.7

Objective lens focal length 19 mm 25 mm 50 mm 100 mm 19 mm 25 mm 50 mm 100 mm

Micro Display HD Display

Core ATN Obsidian “T” II

Eye relief 65 mm

Waterproof rating / IP rating Weather resistant

Video Record Resolution 1280×960 @ 30 fps

Microphone Yes

MicroSD card From 4 to 64 GB

Micro USB Yes

Micro HDMI Yes

WiFi (Streaming, Gallery,

& Controls) iOS & Android

Bluetooth 4.1

GPS (Geotagging, Elevation, etc.)

Yes

OTS-HD 384

1.25 - 5x

OTS-HD 384

2 - 8x

OTS-HD 384

4.5 - 18x

OTS-HD 384

9 - 36x

OTS-HD 640

1 - 10x

OTS-HD 640

1.5 - 15x

OTS-HD 640

2.5 - 25x

OTS-HD 640

5 - 50x

3D Gyroscope Yes, GS7

3D Accelerometer Yes

3D Magnetometer Yes

E-Barometer Yes

E-Compass Yes

Smooth Zoom Yes

Battery life (Li-ion) 8 hr

Battery type 4 AA (Lithium Recommended)

Optional accessories External Battery Pack

Dimensions

6.85”×3.16”×3.14”

174×80.26×80 mm

8.81”×3.16”×3.14”

224×80.26×80 mm

10.67”×3.97”×3.47”

271×101×88 mm

6.85”×3.16”×3.14”

174×80.26×80 mm

8.81” x 3.16” x 3.14”

224×80.26×80 mm

10.67”×3.97”×3.47”

271×101×88 mm

Weight 1.55 lb / 0.68 kg 1.85 lb / 0.84 kg 2.75 lb / 1.24 kg 1.55 lb / 0.68 kg 1.85 lb / 0.84 kg 2.75 lb / 1.24 kg

Warranty 3 years

Human Detection Range 625 800 1500 2500 625 800 1500 2500

Human Recognition Range 280 400 600 1100 280 400 600 1100

Human Identiﬁcation Range 170 250 360 600 170 250 360 600

* ATN reserves the right to change the above specifications at any time without notice

PREPARING THE DEVICE

UNPACKING

The following steps must be accomplished prior to each mission where the device

is used:

1. Open packaging box, remove OTS-HD and check the content.

2. Make sure that nothing is missing.

3. Inspect the device for damage to optical surfaces, body, eyecups, operation

buttons, etc.

4. Ensure that all optical surfaces are clean and ready for use.

NOTE

If any accessories are missing or broken contact ATN’s Customer Service.

INSTALLATION OF BATTERIES

The OTS-HD will operate on four AA-type batteries.

NOTE

We highly recommend using lithium AA

batteries. They will provide much longer

battery life. Use only 1.5 V batteries.

Install batteries as follows:

1. Remove the battery cap by unscrewing it

counter clockwise.

2. Insert batteries as shown.

3. Return the battery cap into the housing

(screw clockwise until finger tight).

Do not over tighten as it will be difficult to

remove the next time you replace batteries.

NOTE

Make sure that the device is turned off before changing sources of energy

(batteries or USB in power supply mode).

MicroSD, USB AND HDMI PORTS

The device is equipped with MicroSD Card, Micro USB and Micro HDMI ports.

You can find them under the cap on the right

side of the device (we marked the cap with

appropriate icons).

To open the cap you should unscrew it coun-

terclockwise.

NOTE

Make sure that the device is turned off before

inserting the microSD card into the slot.

1. A new card should be formatted before

usage.

Micro USB

MicroSD

Micro

HDMI

2. Insert microSD card as shown.

3. To lock the card in the slot push it in with a

thin object (a small coin, paper clip, toothpick,

etc.).

4. Return the cap into the housing (screw

clockwise until finger tight).

NOTE

There is only one correct direction to insert

the MicroSD Card.

Do not force the card into the slot as it may

damage both the scope and the card itself.

To remove the MicroSD Card from the slot,

push it in using the same thin object. When it

pops up a few millimeters, it can be pulled with

your fingers or tweezers.

NOTE

If you are going to record video we recom-

mend using a Class 10 microSD card (10 MB/s)

or faster and have capacity from 4 to 64 GB.

FIRMWARE UPDATE

Before operating your device please update the firmware to the latest version.

To receive a notification of new firmware updates, please register your device on

our website (you’ll receive an email letting you know when new firmware becomes

available).

To update the new firmware you will need a microSD Card and batteries that are

fully charged.

NOTE

In the event of a power failure during an update the device may crash corrupt-

ing its system files and will need to be sent back to the ATN factory for service.

It is important not to use additional sources of power during firmware update!

Update the new firmware as follows:

1. Download the ***.bin file and copy to your microSD Card - root directory

2. Insert the card into the scope

3. Turn ON the scope

4. In the “Firmware Update” dialog box select “Yes” to start the update

5. When the update counter reaches

“100%” the device will automatically restart

6. Once the device is powered up it will

enter self configuration mode

7. After completing it will automatically

restart and will be ready for use

8. Motion Sensing platform will be config-

ured when first turned on.

NOTE

If the device does not restart within 30 seconds, remove and re-insert the

batteries and power-up the device.

Once the device has been updated you will need to either format the card or

delete the update file manually. In the event you do not, the system will ask you

if you wish to update the device every time you turn it on.

ON/OFF

To TURN ON the device press

and hold the POWER button until

you see the ATN splash screen.

To TURN OFF the device press

and hold the POWER button, until

the dialog box “Shut down the

device?” appeares. Choose “Yes”

to turn off.

NOTE

Upon startup you must perform a NUC.

USING KEYPAD

The KEYPAD is programmed to be used in

two different ways:

• Short and Quick Taps — used for most

functions and to get around the menu;

• Press and Hold — designed to be used

on the following situations — ON/OFF, ZOOM,

SHORTCUT MENU.

NOTE

Using LEFT or RIGHT buttons in menu you

can quickly choose Exit Shortcut from any

position.

FOCUSING

DIOPTER ADJUSTMENT

By rotating the Diopter Adjustment Ring you

will achieve optimal sharpness for your vision.

We recommend that you first turn on the Car-

ousel by clicking Enter button and optimizing

your focus by making sure the Icons are sharply

displayed.

NOTE

You do not take the rubber cap off the

objective lens.

You should not need to re-adjust the Diopter Adjustment unless another

user with different vision than yourself will be using the device.

DIOPTER

ADJUSTMENT RING

FOCUS ADJUSTMENT

Remove the cap from the objective lens and

rotate the focus adjustment ring as necessary

to achieve the proper focus at various dis-

tances.

COMPASS CALIBRATION

When the compass needs to be

calibrated the word “CAL” appears

instead of the Compass Scale.

To calibrate you should rotate the

device in three axis as pictured

below.

NOTE

After calibrating the device

please remember that the com-

pass will work best when hold-

ing the OTS-HD parallel to the

ground.

Other possible Errors:

• ERR — an error was detected (you may need to restart the device or recalibrate

the compass);

• SMF — your device is under Strong Magnetic Field (please, move away from

the Magnetic Field);

• UPD — your firmware needs to be updated.

FOCUS

ADJUSTMENT

RING

Inhaltsverzeichnis

Andere ATN Monokular Handbücher

ATN

ATN MO4-3 Bedienungsanleitung

ATN

ATN Night Leopard Bedienungsanleitung

ATN

ATN Night Storm CGT Bedienungsanleitung

ATN

ATN 6015-3 Bedienungsanleitung

ATN

ATN MO2-1 Bedienungsanleitung

ATN

ATN PS14-HPT Bedienungsanleitung

ATN

ATN Voyager 2 Bedienungsanleitung

ATN

ATN Night Storm 2 Bedienungsanleitung

ATN

ATN MO4-1 Bedienungsanleitung

ATN

ATN PS14-3 Bedienungsanleitung

ATN

ATN Night Patriot Bedienungsanleitung

ATN

ATN MO4-4 Bedienungsanleitung

ATN

ATN PVS14-3 Bedienungsanleitung

ATN

ATN Voyager 2IA Bedienungsanleitung

ATN

ATN MO2-1 Bedienungsanleitung

ATN

ATN NVG7-3I Bedienungsanleitung

ATN

ATN ATN Night Shadow 3 Bedienungsanleitung

ATN

ATN PS14-2 Bedienungsanleitung

ATN

ATN NVM-14-3P Bedienungsanleitung

ATN

ATN Ultra Sight DC Bedienungsanleitung

ATN

ATN Night Storm 3 Bedienungsanleitung

ATN

ATN Night Star Bedienungsanleitung

ATN

ATN MO4-2 Bedienungsanleitung

ATN

ATN 8x20 Silver Eye Bedienungsanleitung

Beliebte Monokular Handbücher anderer Marken

Zeiss

Zeiss Victory 8 x 26 T* PRF Bedienungsanleitung

Bushnell

Bushnell Equinox 260228 Bedienungsanleitung

Pulsar

Pulsar 71011 Bedienungsanleitung

PHOTONIS

PHOTONIS TacFusion Bedienungsanleitung

Opticron

Opticron Imagic IS Installationsanleitung

Night Vision

Night Vision NOXM50 Bedienungsanleitung

Leica

Leica Monovid 8x20 Bedienungsanleitung

StellaX

StellaX ZoomX X-003 Bedienungsanleitung

AGM

AGM ASP-MICRO TM160i Bedienungsanleitung

Zeiss

Zeiss DTI 6/20 Bedienungsanleitung

Dali

Dali S25 Series Bedienungsanleitung

Zhumell

Zhumell WATERPROOF ZOOM MONOCULAR 10-25X42 Bedienungsanleitung

Levenhuk

Levenhuk Fatum Z1000 Bedienungsanleitung

Vortex

Vortex Solo 36 mm Bedienungsanleitung

Bushnell

Bushnell 5 X 20 GOLF SCOPE Bedienungsanleitung

Bushnell

Bushnell Equinox Z 260130 Bedienungsanleitung

Night Owl

Night Owl Night Scope NOXM50-DG Bedienungsanleitung

Yukon

Yukon PHANTOM 26057T Montageanleitung