Atomic Zombie StreetFox Bedienungsanleitung
Build the StreetFox Recumbent Trike
Another Atomic Zombie™ Extreme Machines Adventure
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 1
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike
Table of Contents
About the StreetFox............................................................................................................ 3
Forks, Crowns and Head Tubes.......................................................................................... 6
Axles and Mounting Tabs................................................................................................. 14
The Frame......................................................................................................................... 25
Seat Tube .......................................................................................................................... 30
Front Wheel Arms............................................................................................................. 37
Joining the Booms............................................................................................................. 45
Head Tube Angles............................................................................................................. 49
Suspension ........................................................................................................................ 59
Brake Support Arms ......................................................................................................... 62
Ackermann Steering.......................................................................................................... 70
Bottom Bracket and Derailleur......................................................................................... 79
Pulleys and Chains............................................................................................................ 89
Seating............................................................................................................................... 92
Handlebars ........................................................................................................................ 94
Adjustable Backrest.......................................................................................................... 97
Return Chain Idler........................................................................................................... 100
Front Brakes.................................................................................................................... 103
Basic Seat Design ........................................................................................................... 105
Trim Excess Main Boom and Paint................................................................................ 114
Final Adjustments and First Ride ................................................................................... 116
Showing Off Your New Wheels!.................................................................................... 123
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 2
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike StreetFox Characteristics
About the StreetFox
The StreetFox Recumbent Trike is a fast and comfortable version of
the classic "tadpole" style trike (two wheels in the front), which includes rear
suspension, three wheel braking, and 26 inch rear wheel for optimal gear
range. The StreetFox looks and handles as well as many commercially
produced trikes, and can be completely built using commonly available and
inexpensive bicycle components and some square tubing. Not one single
machined part is needed.
The StreetFox also includes an adjustable bottom bracket so it can fit
riders of just about any height from 5 feet to well over 6 feet tall. Due to the
rugged construction and use of sturdy 14 mm axle, 48 spoke front wheels,
the StreetFox can accommodate riders over 250 pounds. There is plenty of
room for customization due to the simple mono boom frame, so you can
alter the design to suit your own style or needs.
Figure 1 – A 26 inch suspension frame and rear wheel
The good news is that the entire rear of the trike is an unmodified
stock rear triangle from a typical suspension mountain bicycle. As shown in
Figure 1, you will need the complete rear triangle, the suspension spring, and
at least the part of the main frame that contains the tube that connects the
rear triangle to the frame, allowing it to pivot. The front part of the frame is
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 3
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike StreetFox Characteristics
not important, so it can be in any shape as long as the rear of the frame is
perfectly functional.
Since you can purchase an entire bicycle for not much more than
$100, I decided to work with new parts, as this would ensure the suspension,
wheel, and brake parts wee all in perfect working order. I ended up using the
front half of the mountain bike for an electric project called "The Long
Ranger", so every part of the inexpensive department store bike went to
good use. If you decide to consult your scrap pile or the local dump for parts,
ensure that the rear brakes are working, and that the rim is not damaged in
any way.
Figure 2 - A pair of 20 inch BMX wheels
One of the main concerns when designing a tadpole type trike is how
to connect the two front wheels to the steering components. The obvious
answer would be to simply find a pair of typical 20 inch front wheels then
move the threaded hub axle to one side and then bolt it to something strong
enough to support it. This answer is partially correct. The problem with this
approach is that a typical bicycle hub will not have an axle strong enough for
connection on a single side, and your axles would bend as soon as you enter
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 4
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike StreetFox Characteristics
the first corner, or before you even make it to the end of your driveway if
you weigh more than 180 pounds.
Sure, you could probably build a kid's trike using the largest mountain
bike hub axles you can find, but this would still be a risky design, as the first
bounce up a curb would certainly bend the axles. Another factor in choosing
trike wheels is their lateral strength. Since a trike cannot lean into the
corners, the two front wheels are going to be under massive stress around
any corner at higher speeds. For this reason, almost all tadpole style trikes
use 20 inch or 16 inch front wheels with at least 36 spokes due to their
excellent strength.
You may be thinking that this project calls for a pair of expensive
rims mounted to a set of custom made hubs, but the good news is that you
can purchase a pair of sturdy 20 inch trike wheels from any bicycle shop in
the form of 14 mm axle, 48 spoke BMX wheels like the pair shown in
Figure 2. Unless you have an unlimited budget, or really know the dynamics
of bicycle wheels and plan to make your own hubs, the BMX wheel route is
the best way to go. You can expect to pay between $100 and $200 for a pair
of suitable wheels complete with smooth tread tires from a bicycle shop.
Figure 3 - Hub axles. Yes, size does matter
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 5
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike StreetFox Characteristics
As you can see in Figure 3, the difference in axle size between a
common bicycle hub and the 14 mm BMX hub is amazing. The 14 mm axle
on the BMX hub is made for serious abuse, and if you have ever seen a
BMX freestyle competition, then you know what I mean when I say these
wheels are indestructible. The smaller axle would be barely enough to hold
up a kid's stroller if held by only one side, but the BMX axle would easily
survive trike use with a rider at roughly 250 pounds. I have made several
trikes using these hubs, and I can assure you, the crazy stunt riding I did
went far beyond what most "sane" riders would ever consider doing on a
trike! So as a general rule, do not use any threaded axle less than 14 mm in
diameter, and do not use a wheel with less than 36 heavy gage spokes.
Follow this rule, and you will never bend an axle or "taco" a wheel.
Forks, Crowns and Head Tubes
Figure 4 - Finding two identical head tubes
When you are sourcing steering parts for the front of a tadpole trike,
you will basically need two of everything when it comes to the front wheels.
As you can see in the completed StreetFox photos, the steering system is
made using bicycle components so you do not need any expensive machine
shop work done, and the resulting steering system is much smoother than the
traditional kingpin bolt style steering system often found on go-carts. Your
goal is to find two identical head tubes and the fork hardware to match.
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 6
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike Front Hardware
When I say identical, I am not referring to color or brand, but the overall
length and width of the head tube so that both front wheels will be at the
same height when the parts are installed. As shown in Figure 4, I have two
identical head tubes and two matching fork stems that fit into the head tubes.
All of my parts are from at least three different bicycles, but they are
all the same size, and that is all that really matters. If you don't have access
to a large bicycle scrap pile, then you could trim a head tube down an inch or
two to match the other one, but keep in mind that you will also need to cut
the fork threads, and could end up with not enough thread to install the fork
hardware by cutting away too much of the threaded tubing. Also, do not
worry about the condition or size of the fork legs, as they are not being used.
Just make sure that the fork stem is not bent.
Figure 5 - Checking the fork hardware
It doesn't matter if the head tube is from a 1960’s beach cruiser and
the forks are from a competition BMX bike as long as the hardware fits
together properly and the forks spin around without friction. I ended up
using a 20 inch and a 26 inch fork, but again, this doesn't matter, as the fork
legs are soon to be cut from the fork stem. As shown in Figure 5, fork
hardware consists of two bearing cups, a pair of bearings, and at least two
locking nuts. Bearings are inserted into the cups "balls first", and the fork
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 7
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike Front Hardware
stem should spin without friction of the bearings and cups are the correct
size. There are at least three different cup sizes, so the wrong bearing will
cause friction, making it difficult to spin the fork stem.
Figure 6 – Removing the bearing race
Before you start amputating the fork legs from the fork stem, first tap
off the small bearing race (Figure 6) installed just above the fork crown by
tapping it with a small hammer. Tap all the way around the ring until it falls
off so you can work on the fork legs without risk of damaging the bearing
race with our hacksaw or angle grinder.
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 8
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike Front Hardware
Figure 7 - Cutting the fork legs from the stem
How you cut the fork legs from the fork stem is up to you, but do try
to avoid cutting into the fork stem when you are doing this job on both forks.
I like to cut around the fork leg using a cut-off disc in my grinder, leaving
about 1/4 inch as shown in Figure 7. I then finish up the surface grinding
with a rough grinder disc and then clean the area with a flap (sanding) disc.
Keep the fork legs around for some other project; they make good head rest
supports or seat frames.
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 9
www.ATOMICZOMBIE.com
StreetFox Tadpole Trike Front Hardware
Figure 8 – Mark the crowns for trimming
At this point, you have two perfectly clean fork stems as shown in
Figure 8. The length of the crown area may not match on both fork stems,
but this does not matter since we will be cutting them down to 1 inch to
remove the excess crown area. A bit of tape around the crown area will
make a good cutting guide, or you can draw a line around the crown using a
marker. The cut line should be 1 inch from the top of the crown where the
underside of the bearing race would have been sitting.
All content copyright Atomic Zombie Extreme Machines. All rights reserved. 10
www.ATOMICZOMBIE.com
Inhaltsverzeichnis
Andere Atomic Zombie Fahrrad Handbücher
