ATOMSTACK MAKER R1 Bedienungsanleitung
ATOMSTACK MAKER R1 Rota Chuck
English
F03-0135-0AA1
Versions: A
Catalog
1. Packing list
2. Heightening feet installation
3. Connection cable use
4. Product use introduction
5. Installation guide
6. LightBurn software use
7. Notes
1
2
3
5
6
12
15
1
1.Packing list
Chuck body assembly
H2.5 Hexagonal Plate Handle*1PCS
H3.0 Hexagonal Plate Handle*1PCS
black plug wire*1PCS White plug wire*1PCS� Caliper*1PCS
Heightened feet *4PCSScrew 3*6mm(6PCS) Instruction manual
Mini level meter *1PCS
Soft ruler*1PCS
Hexagonal jaws*3PCS
Suppo column assembly L-shaped jaws*3PCS Ladder jaws*3PCS
2
2.Heightening feet installation
1. When you need to work with the chuck to engrave or cut wide suace objects, you need to install the heightening foot. The laser
engraver can be raised to engrave or cut taller objects by installing heightening foot accessories.
1.1 Chuck and heightening feet with the use of diagrams
1.2 Heightened feet
Heightened feet
Engraving Machine
Chucks
3
1. The chuck has two connecting wires, black plug and white plug, note that they are wired in a dierent order and need to be
connected carefully.
1.1 White plug wire connection sequence 1.2 The connection sequence of black plug wires
4PIN white plug cable for connecting ATOMSTACK laser engraving machine.
4PIN black plug cable for connecting to third pay laser engraving machine.
The R1 chucking kit suppos ATOMSTACK and third pay laser cutters and engravers. You need to connect it to the device and use the appropriate software to operate it. If you
cannot connect it, please change the order of the wires and change the processing as shown in Figure 1.1-1.2.
3.Connection cable use
4
1.1 Terminal plug for connecting the chuck
1.2 White plug cable for Atomstack 1.3 Black plug wire other brands use
Connection socket
Y-axis motor wire plug Chuck motor plug Y-axis motor wire plug Chuck motor plug
3.Connection cable use
5
4.product use introduction
Product pofolio using accessories Engraved shapes/items
Rings (rings and other smaller diameter circles)
Circles (larger diameter circles such as bracelets)
Circles (larger diameter circles such as bracelets)
Cylindrical
Goblets
Cylindrical
Goblets
Sphere, egg-shaped (cued suace is not
obvious), non-inveible
Sphere, egg-shaped (cued suace is not
obvious), non-inveible
Circles (larger diameter circles such as bracelets)
6
Clockwise for locking, counterclockwise for unlocking
5.Installation guide
Step 1: Direction of chuck rotation
7
Step 2 (A1): Installation of L-shaped jaws (method 1)
Screw 3*6mm
L-shaped jaws
H2.5 hexagonal
plate hand
Suppo column assembly
5.Installation guide
Key points of operation: the sphere should stick to the three jaws as far as possible, and then The
suction cup of the rear suppo column is attached to the sphere, and then tightened screw. When
disassembling the ball, you can put the chuck Loosen, then move the suppo column back.
Note:
1. When engraving a cued suace, take the average value of the diameter/circumference of the
actual engraving range of the measured object (the average value of the left, middle and right of
the engraving range position)
2. When tilting and engraving, adjust the appropriate position of engraving by rotating the button
3. Round bottom object engraving
8
L-shaped jaws
Screw 3*6mm
H2.5 hexagonal
plate hand
Step 2 (A1): Installation of L-shaped jaws (method 2)
5.Installation guide
Note:
1. When engraving a cued suace, take the average value of the diameter/circumference of the actual engraving
range of the measured object (the average value of the left, middle and right of the engraving range position)
2. When tilting and engraving, adjust the appropriate position of engraving by rotating the button
3. Round bottom object engraving
Inhaltsverzeichnis
Sprachen:
Andere ATOMSTACK Industrieanlagen Handbücher
ATOMSTACK
ATOMSTACK R3 Rotary Roller Bedienungsanleitung
ATOMSTACK
ATOMSTACK R2 V2 Bedienungsanleitung
ATOMSTACK
ATOMSTACK X40 Pro Bedienungsanleitung
ATOMSTACK
ATOMSTACK R2 Bedienungsanleitung
ATOMSTACK
ATOMSTACK MAKER FB2 Plus Bedienungsanleitung
ATOMSTACK
ATOMSTACK MAKER E85 Bedienungsanleitung
ATOMSTACK
ATOMSTACK M4 Bedienungsanleitung
