Attero Tech UnD3IO Bedienungsanleitung

unD3IO

User Manual

Attero Tech, LLC

1315 Directors Row, Suite 107, Ft Wayne, IN 46808

Phone 260-496-9668 • Fax 260-496-9879

www.atterotech.com

614-00017

unD3IO

2-in/2-out Dante Wallplate with Multi-IO Analog

Connectivity

User Manual

Date 03/14/2018

Revision 05_b

unD3IO

User Manual

Attero Tech LLC 2018 Page 1 614-00017 Rev 05_a

IMPORTANT SAFETY INSTRUCTIONS

The symbols below are internationally accepted symbols that warn of potential hazards with electrical products.

This symbol, wherever it appears, alerts you to the presence of un-insulated dangerous voltage inside the

enclosure -- voltage that may be sufficient to constitute a risk of shock.

This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the

accompanying literature. Please read the manual.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and third grounding prong. The wider

blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11. Only use attachments/accessories specified by Attero Tech

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus.

13. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

14. Unplug this apparatus during lightning storms or when unused for long periods of time.

15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

16. This apparatus shall be connected to a mains socket outlet with a protective earthing connection.

17. When permanently connected, on all-pole mains switch with a contact separation of at least 3mm in each pole

shall be incorporated in the electrical installation of the building.

18. If rack mounting, provide adequate ventilation. Equipment may be located above or below this apparatus but

some equipment (like large power amplifiers) may cause an unacceptable amount of hum of may generate too

much heat and degrade the performance of this apparatus,

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

unD3IO

User Manual

Attero Tech LLC 2018 Page 2 614-00017 Rev 05_a

LIMITED FIVE YEAR WARRANTY

The equipment is warranted for five years from date of purchase from Attero Tech, LLC against defects in materials or

workmanship. This warranty does not cover equipment which has been abused or damaged by careless handling or

shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Attero Tech,

LLC will, at our option, repair or replace any defective parts without charge for either parts or labor. If Attero Tech, LLC

cannot correct the defect in the equipment, it will be replaced at no charge with a similar new item. Attero Tech, LLC

will pay for the cost of returning your equipment to you. This warranty applies only to items returned to Attero Tech,

LLC, shipping costs prepaid, within five years from the date of purchase. This Limited Warranty is governed by the laws

of the State of Indiana. It states the entire liability of Attero Tech, LLC and the entire remedy of the purchaser for any

breach of warranty as outlined above. NEITHER ATTERO TECH, LLC NOR ANYONE INVOLVED IN THE PRODUCTION OR

DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, CONSEQUENTIAL, OR

INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF ATTERO TECH, LLC HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF ATTERO TECH, LLC

EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT.

This warranty gives you specific legal rights. You may have additional legal rights which vary from state to state.

Note: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules and EN55022. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference,

in which case the user will be required to correct the interference at his own expense.

unD3IO

User Manual

Attero Tech LLC 2018 Page 3 614-00017 Rev 05_a

Contents

1 - Overview ..................................................................................................................................................................................................................... 4

1.1 –What’s in the Box ..................................................................................................................................................... 4

2 –Device Installation................................................................................................................................................................................................. 5

2.1 –Mounting .................................................................................................................................................................. 6

2.2 –Hardware Connections ............................................................................................................................................. 6

2.2.1 –Balanced Source to Balanced Sink.................................................................................................................... 6

2.2.2 –Unbalanced Source to Balanced Sink ............................................................................................................... 6

2.2.3 –Balanced Source to Unbalanced Sink............................................................................................................... 7

2.2.4 –Unbalanced Output to an Unbalanced Sink..................................................................................................... 7

3 –Device Configuration ........................................................................................................................................................................................... 8

3.1 –IP Address Setup ...................................................................................................................................................... 8

3.2 –Software Installation................................................................................................................................................. 8

3.3 –Selecting a Network Adapter.................................................................................................................................. 10

3.4 –Connecting to a Device .......................................................................................................................................... 10

3.5 –Device Identification............................................................................................................................................... 11

3.6 –Device Controls ...................................................................................................................................................... 11

3.7 –Saving and Loading Settings .................................................................................................................................. 11

3.7.1 –Internal Presets .............................................................................................................................................. 11

3.7.2 –Preset Files ..................................................................................................................................................... 12

4 –3rd Party Control................................................................................................................................................................................................... 13

4.1 –Command Interface Type....................................................................................................................................... 13

4.2 –Using the Command interface ............................................................................................................................... 13

5 –ARCHITECTS & ENGINEERS SPECIFICATION ........................................................................................................................................... 14

5.1 –Device Specifications.............................................................................................................................................. 14

APPENDIX A –Reference Documents...............................................................................................................................................................A-1

unD3IO

User Manual

Attero Tech LLC 2018 Page 4 614-00017 Rev 05_a

1 - Overview

The unD3IO DanteAudio interface is a cost effective multi-IO wall box and is designed to fit into most dual gang US

junction boxes. Its size and I/O density make it easy to put Dante connectivity wherever it’s needed – near the audio

source or sink –thereby eliminating costly and interference prone analog wiring.

Figure 1 - unD3IO front view

The unD3IO features two Dante input and two Dante output channels. The analog I/O are configurable via software to

support different connectivity configurations. The XLR connector provides balanced mic/line audio to Dante output

channel 1. However, the second Dante output comes from one of three possible input mixes:

oA mono mix of the RCA jack inputs

oA mono-mix of the 3.5mm stereo jack inputs

oA combined mix of the RCA inputs and the stereo jack inputs

The user can select which mix they require through the control software.

The unD3IO has two output options. An XLR connector provides a balanced line output for analog output 1 only, and a

3.5mm stereo jack connector provides an unbalanced line level output for both analog output 1 and analog output 2.

Both output connectors may be used simultaneously.

Connection to the Dante network is provided by a single Ethernet RJ45 connector on the back of the unit. The unD3IO

is PoE-enabled which allows it to be powered over its network cable from a suitable PoE source (IEEE 802.3af-compliant)

and eliminating the need for a local power supply. This is particularly useful as the unD3IO can then be mounted in

remote locations where access to a mains outlet would be limited or indeed, non existent.

Audinate’s Dante Controller or other 3rd party manufacturer's Dante routing software can be used to control the audio

routing configuration of the device while the Attero Tech unIFY Control Panel application can be used to configure the

device-specific features.

The unD3IO also supports control by third party systems allowing external configuration of its settings such as

phantom power and input gain in real time. Further information on 3rd party control can be found later in this

document in section 4.

1.1–What’s in the Box

The unD3IO comes supplied with the following

ounD3IO device

oMounting kit

oDecora plate

Dante is a trademark of Audinate Pty. Ltd.

unD3IO

User Manual

Attero Tech LLC 2018 Page 5 614-00017 Rev 05_a

2 –Device Installation

Power/ ID LED

Balanced audio input (Input 1)

Unbalanced RCA Audio inputs (Input 2A)

Unbalanced stereo 3.5mm jack audio input (Input 2B)

Balanced audio output (Output 1)

Unbalanced stereo jack audio output (Output 1 & 2)

*Note: The unD3IO has a label on the front of the metal housing at the top that shows the last 6 digits of the MAC

address. This is important for initial device identification as these digits make up part of the devices default network

name that is shown when the device is detected by Dante Controller. The full MAC address is also given on the back of

the unit.

unD3IO

User Manual

Attero Tech LLC 2018 Page 6 614-00017 Rev 05_a

2.1 –Mounting

A typical installation will involve mounting the wall plate into the wall using an “old-work” type bracket or a pre-

mounted wall box. Before starting, make sure the wall box where the unD3IO is to be installed is pre-wired with a

suitable cable back to a PoE enabled network switch or mid-span injector. If a mid-span injector is being used, the

cable should be connected to the port that supplies both Ethernet and power (refer to the manual for the midspan

injector if unsure which port is which).

*Note: All Attero Tech products are tested using UTP cabling and it is recommended that UTP cabling be used when

installing them. STP cabling can be used for installation though care must be taken not introduce grounding issues into

the system by doing so.

Attach the network cable from the switch/mid-span injector to the Dante I/F port of the Dante unD3IO. If the switch or

mid-span injector is already running and PoE is enabled, the unit should power up and the green ID LED on the front of

the device should turn on.

With the cable attached, carefully place the unD3IO into the wall box taking care to not trap the cabling. Once fully in

place, secure with the screws provided. Once the unit is secured in the wall box, fit the Decora plate and secure it with

the screws provided with it.

2.2 –Hardware Connections

The unD3IO accepts and drives either unbalanced or balanced audio devices. Refer to the following diagrams and

instructions for connecting different types of audio devices. Professional grade audio cabling is recommended to

achieve the best audio performance throughout the system.

2.2.1–Balanced Source to Balanced Sink

To connect balanced sources to the unD3IO XLR input or connecting a balanced sink to the unD3IO XLR output, use a 2-

core cable with a shield and connect positive output to positive input, and negative output to negative input using the

cable cores, and connect output ground to input ground using the cables shield.

Source +

Sink

Shield

Figure 2 - Balanced Source to Balanced Sink Connection

2.2.2 –Unbalanced Source to Balanced Sink

Use the following if using a single core cable with shield to connect a 2-wire unbalanced source to XLR input on the

unD3IO, or to connect an RCA or stereo jack unbalanced output signal from the unD3IO to a balanced input on another

device. Connect the positive output of the unbalanced source to the positive input of the balanced sink. Connect both

the source and sink input grounds together and short the negative input of the sink to ground at the input of the sink.

Source +

Shield

Sink

Figure 3 - 2-Wire Unbalanced Source to Unbalanced Sink Connection

unD3IO

User Manual

Attero Tech LLC 2018 Page 7 614-00017 Rev 05_a

For the same connections but using a 2-core + shield cable, connect the positive and grounds as before but this time,

short the negative conductor to the shield at the source connection instead.

Source +

Shield

Sink

Figure 4 - 3-Wire Unbalanced Source to Balanced Sink Connection

2.2.3 –Balanced Source to Unbalanced Sink

Use the following if using a single core cable with shield to connect a balanced source to an RCA or stereo jack input on

the unD3IO or to connect the XLR output from the unD3IO to an unbalanced input on another device. Connect the

positive output of the balanced source to the positive input of the unbalanced sink. Connect both the source and sink

input grounds together and short the negative input of the source to ground at the output of the source.

Source

Shield

Sink

Figure 5 - 3-Wire Balanced Source to Unbalanced Sink Connection

For the same connections but using a 2-core + shield cable, connect the positive and grounds as before but instead,

short the negative conductor to the shield at the sink end of the cable instead.

Source

Shield

Sink

Figure 6 - 3-Wire Balanced Source to Unbalanced Sink Connection

2.2.4 –Unbalanced Output to an Unbalanced Sink

To connect an unbalanced source to unD3IO RCA or stereo jack input, or connect the stereo jack output to an

unbalanced sink, connect the positive output to the sink’s positive input and connect the grounds together through the

cable shield.

Sink

Shield

Source

Figure 7 –Unbalanced Source to Unbalanced Sink Connection

unD3IO

User Manual

Attero Tech LLC 2018 Page 8 614-00017 Rev 05_a

3 –Device Configuration

There are two parts of the device that require software to setup. First the audio routing, and second the configurable

features of the device itself.

The audio routing should be carried out using any application that supports Dante audio routing. This could be from a

3rd party manufacturer or be Audinate’s own Dante Controller. Dante Controller can be obtained from the Audinate

website (www.Audinate.com). Instructions on how to use this software and about setting up routes on a Dante network

can also be found on Audinate’s website.

*Note: When using Dante controller, the unD3IO will be shown using a default device name of unD3IO-###### where

‘######’ is the last six characters of the devices MAC address.

Configuration of the unD3IO specific features is carried out using the Attero Tech unIFY Control Panel application. This

application is available from the Attero Tech website (www.atterotech.com). It is used to initially configure the device

and can examine and modify the device specific features such as mic/line gain settings, phantom power, and output

boost options. The unD3IO features are supported in unIFY Control Panel V1.3 or later.

The unD3IO also supports 3rd party control systems by configuration with direct UDP messages. Further information on

using this facility can be found in the unIFY 3rd Party Control –Software API document available from the Attero Tech

website.

3.1 –IP Address Setup

******************************************************* IMPORTANT ****************************************************

Failure to correctly configure IP addresses will not allow an unD3IO device to correctly authenticate in the unIFY Control

Panel software and while it will show up in Dante Controller, the input and output channels won’t be visible and routing

of audio to and from the unD3IO will not be possible.

****************************************************************************************************************************

In order to configure an unD3IO both to set up its internal parameters and also setup audio routing, the PC will need to

be able to communicate with it over the network. While all Dante devices will be discovered regardless of the IP address

setup on the PC, communication can only occur if the PC and the device have compatible IP addresses.

By default, unD3IO is set to get a dynamic IP address. As with all Dante devices, if the unD3IO device does not find a

DHCP server to retrieve an IP address from, it will give itself an automatic private IP address (APIPA) instead. An APIPA

is always in the range 169.254.x.y.

To ensure communication, the PC can either be set to get a dynamic IP address, or be given a static IP address in the

range 169.254.x.y. The PC may require a restart for the changes to take affect.

Further information on IP setup for an audio system using Dante can be found in the FAQ’s on the Audinate website

(https://www.audinate.com/resources/faqs).

3.2 –Software Installation

After downloading the application, run the .exe and the first screen to appear will be the license agreement and options

screen.

unD3IO

User Manual

Attero Tech LLC 2018 Page 9 614-00017 Rev 05_a

The software will install to a default location of c:\program Files (x86)\Attero Tech\unIFY Control Panel). Clicking the

“Options” button allows the user to change the installation location if required though it’s not necessary to change it.

To select a new installation location, either type in a new path in the edit box, or click on the “Browse” button to browse

the folder tree for the desired installation location. Once complete, click the OK button to return to the previous

screen.

To continue the install, read the license agreement and check the “I agree…” check box. Doing so enables the “Install”

button. Click the now enabled “Install” button to start the installation of the files.

On Windows Vista or later if the PC has the UAC enabled, a warning pop up will now appear saying the installer is about

to make changes to your PC. This needs to be accepted for the installation to complete successfully.

The installer will show a progress screen and will now being transferring files to your PC.

Once the files are transferred, the installer will show a completion message show whether the installation was

successful or not.

If the installation was unsuccessful for any reason, the final screen will show an error message.

Inhaltsverzeichnis

Andere Attero Tech E/A-System Handbücher

Attero Tech

Attero Tech Dante unD6IO-BT Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

Attero Tech unD3IO Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken