Audiovox Rampage AMP-610 Bedienungsanleitung

OwOw

Ownene

nene

ner'sr's

r'sr's

r's

ManualManual

Manual

Model AMP-610

500 Watt Stereo Amplifier

INDEX

Specifications.............................................................................1

Precautions................................................................................2

InstallationInstructions................................................................3

ControlsandIndicators.............................................................4-7

WiringInstructions.......................................................................7

4-ChannelandMixed-MonoInput WiringDiagram.........................8

4-ChannelandMixed-MonoOutput WiringDiagram......................9

3-ChannelInput WiringDiagram..............................................10

3-ChannelOutput WiringDiagram WiringDiagram.......................11

2-Channel Mono (Bridged) Input Wiring Diagram ...................12

2-ChannelMono(Bridged)Output WiringDiagram...................13

Warranty.........................................................................................14

HIGH PERFORMANCE STEREO AMPLIFIER

Thispoweramplifierhasbeendesignedtoprovidehighqualityperformancewitha

minimumofmaintenance. However,it'sperformancewillonlybeasgoodasthecare

andqualityofcomponentswithwhichitisinstalled. Wethereforeadvisethatyouread

these instructions very carefully to familiarize yourself with the product and it's

features.

Shouldyou require assistancewith the installationor wiring ofthis unit, pleasecall

ourtoll-free"HELP"lineat1-800-645-4994duringthedays/hoursshown.

Monday - Friday

Saturday

8:30am - 7:00pm Eastern

9:00am - 5:00pm Eastern

1-800-645-4994

HELP!

SPECIFICATIONS

-1-

*Due to continuing improvement, Audiovox reserves the right to change features and design without notice.

MaximumOutputPower

4-ChannelOperation: 125 watts x 4

2-ChannelOperation: 500 watts x 2

Output Power @ 1% T.H.D.

4-ChannelOperation: 600 watts RMS x 4

2-ChannelOperation: 120 watts RMS x 2

OutputImpedance: 2 - 8 ohms (stereo)

4 - 8 ohms (mono)

FrequencyResponse: 10 - 50,000 Hz. ± 1 dB

ChannelSeparation: 55 dB

Signal / Noise Ratio: 90dB(A-Weighted)

InputImpedance: low-level10Kohms

high-level100ohms

Input Sensitivity: low-level 200 mv. - 5 v.

high-level 2 - 10 v.

SupplyVoltage: 12 volts, negative ground

FuseRating: 20 amps.

Dimensions (W x H x D): 9" x 2-1/4" x 10-5/8"

230 mm x 57 mm x 270 mm

PRECAUTIONS

1. Althoughthisunitisdesignedwithbuilt-inself-protectioncircuits,theremaybeapossibilityofdamageifitis notwired

correctly. Please follow the wiring instructions carefully for the type of system being used.

2. Thelastleadtobe connected is thewiretothe positive (+)terminalofthe battery. Connect thiswireonlyafter having

completed and checked all other connections to the amplifier.

3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that

heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the

temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down

sufficiently.

4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The

use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully

check all electrical connections to the unit.

5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery

and chassis ground must be of a thick enough gauge to provide this voltage to the amplifier. We recommend

#16 gauge wire or thicker (smaller gauge #) for the battery and ground leads.

6. Make certain that the speaker(s) to be used with this amplifier are capable of handling the output power (wattage)

of the unit. Use of speaker(s) not rated for the output of this amplifier may cause damage to or failure of the

speaker(s) for which Audiovox will not be liable.

-2-

INSTALLATION INSTRUCTIONS INSTALLATIONDIAGRAM

1. Select a mounting area where the amplifier will

havesufficientair circulation for proper cooling.

Inadequateaircirculationwillcausethetemperature

of the amplifier to rise and will trigger the

thermal protection mode.

2. Place the amplifier on the mounting surface

and mark the locations of the four mounting

holes as shown in the illustration.

3. Remove the amplifier and drill a 1/8" hole at

each of the four locations.

CAUTION: Before drilling the holes, look at the

underside of the mounting surface. Always

check carefully to avoid drilling into wiring,

braces, fuel or brake lines. CHECK BEFORE

YOU DRILL !

4. Secure the amplifier to the mounting surface

using the self-tapping screws provided.

-3-

CONTROLS AND INDICATORS

7 9

-4-

1Power Indicator/Protection Mode LED

The Power Indicator LED will light to indicate that the unit isconnected to the battery and that the Remote Turn-On terminal is

receiving +12 volts, thus turning on the amplifier.

This LEDilluminates red toindicate that the self-protection circuitshave been activatedand have shutoff operation of the amplifier.

The protection circuits may be triggered by the temperature of the unit rising above a safe level or by an overload condition. If

activated by a rise in temperature,the unitwill resumeoperation aftercooling off to a normal operating range. If activated by

anoverloadcondition,thesourceoftheoverloadmustbefoundandcorrectedtoresumeoperationoftheamplifier. Most

overload conditions are caused by mis-wiring or operation into incorrect speaker loads. Re-check all wiring and

connections if this situation occurs and correct as necessary.

2Level (Gain) Control

The amplifier is capable of operating from sources supplying a wide range of input levels. The Level control should initially be set to

themid-rotationposition. Ifitisfoundthatthereisnotenoughoutputevenwhenthevolumecontrolonthecarstereoisatitsmaximum

setting, adjust the Level control to increase the output from the system. If, however, there is still output from the amplifier when the

car stereo volume control is at its minimum setting, or the output level increases too fast with a small rotation of the volume control,

adjustthe Level controltodecreasethe output fromthesystem. Once the correctsettingis found, thiscontrolshouldnot requireany

further adjustment.

3Low Level Input Connections

If low-level outputs are provided from the car stereo, it is recommended that the low-level inputs be used for lowest distortion

andbestperformance. UsegoodqualityshieldedaudiocableswithRCAplugsatbothendstoconnectthestereototheamplifier

and keep the cable lengths to a minimum to avoid noise.

CAUTION: Use either the low-level or the high-level inputs on the amplifier.

DO NOT use both input levels at the same time.

-5-

4High Level Input Connection

Ifthecarstereodoesnotprovidelow-leveloutputs,theamplifiermaybeconnectedviathespeaker(high-level)outputsfromthestereo.

Wirethespeaker leads from the car stereo to the5-pin adaptor harnessas shown inthe diagram (shieldedcable isnot required for

thisapplication)andplugtheconnectorintothematingHigh-LevelInputsocketontheamplifier. Carefullyspliceandinsulateallwire

connections.

5Fuse

The circuitry of the amplifier is protected from damage byan automotive-type fast-blow fuse. If fuse replacement is necessary,

use only fuses of the same ampere rating as originally supplied with the unit. The use of fuses with incorrectratingsmaycause

serious damage to the amplifier. If fuses blow consistently, carefully check all electrical connections to the unit.

6Power Connection

Thebatteryterminal(BATT)mustbeconnecteddirectlytothepositiveterminalofthevehiclebatterytoprovideanadequatevoltage

source and minimize noise. Connecting the battery terminal lead to any other point (such as the fuse block) will reduce the power

output and may cause noise and distortion. Use only #16 gauge or thicker (smaller gauge #) wire for this lead and connect it to the

terminal of the battery after all other wiring is completed.

7Ground Connection

Thegroundterminal(GND)connection is also critical to the correct operation of the amplifier. Use a wire ofthe same gauge as the power

connection (#16 or thicker) and connect it between the ground terminal (GND) of the amplifier and a metal part of the vehicle close to the

mountinglocation. Thiswire shouldbeasshortaspossibleandanypaint orrustatthegroundingpointshouldbescraped awaytoprovide

a clean metal surface to which the end of the ground wire can be screwed or bolted.

8Remote Turn-On Connection

Theamplifieristurnedonbyapplying+12voltstotheremoteturn-onterminal(REM). Thewireleadtothisterminalshouldbeconnectedto

the"Auto-Antenna"leadfromthecarstereowhichwillprovidethe+12voltsonlywhenthecarstereoisturnedon. Ifthecarstereodoesnot

-6-

The wiring of your amplifier will depend on the system and speakers you are using but will either be a stereo, mono, or mixed-

mono application. The following pages illustrate the input and output wiring for both types. Please refer to the appropriate

diagrams for the system configuration you are using.

The power and speaker wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw

fortheconnectiontobemadeandfully insertthe wire(strip1/2"ofinsulationfromtheend)intotherespective screwon theside

panel(crimp-on "U" terminals areprovided tosimplify wiring and we recommendtheiruse.) Tighten the screw down tosecure

the wire. After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo

or speaker system with which it is used.

WIRING INSTRUCTIONS

-7-

providean Auto-Antennalead,the remoteturn-onleadmay bewiredto an"Accessory"or"Radio" terminalinthe car'sfuseblock. This will

turntheamplifieronandoffwiththeignitionkey,regardlessofwhetherthecarstereoisonoroff. Theremoteturn-onleaddoesnotcarrylarge

currents, so #20 gauge wire may be used for this application.

9Speaker Connections

Dependingonthetypeandnumberofspeakersusedwiththeamplifier,wirethemtothespeakerterminalsaspertheappropriate

wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20

gauge. Forleadsinexcessof10feet,#16gaugeisrecommended. Whenwiringthespeakers,paycarefulattentiontothepolarity

oftheterminalsonthespeakersandmakecertaintheycorrespondtothepolarityofthecorrespondingterminalsontheamplifier.

DO NOT ground any speaker leads to the chassis of the vehicle.

-8-

USETHISINPUTWIRINGWITH

OUTPUTWIRINGONPAGE 9

4-CHANNEL AND MIXED-MONO INPUT WIRING DIAGRAM

LOW-LEVEL

RCAOUTPUTSHIGH-LEVEL

(SPEAKER)OUTPUTS

CARSTEREO

LEFT REAR +

RIGHT REAR +

RIGHT FRONT +

GREEN

WHITE

BLACK

BROWN

GRAY

CH1

CH2

CH3

CH4

IMPORTANT

USEEITHERHIGH-LEVELOR

LOW-LEVELINPUTS,NOTBOTH.

RCATYPE

SHIELDEDCABLES

(NOTINCLUDED)

LEFT FRONT

RIGHT REAR

RIGHT FRONT

LEFT REAR CHASSIS GROUND

ON RADIO

5-PIN

CONNECTOR

LEFT FRONT +

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Audiovox Verstärker Handbücher

Audiovox

Audiovox Jensen A34XP Bedienungsanleitung

Audiovox

Audiovox Prestige PAB-2150R Bedienungsanleitung

Audiovox

Audiovox Menace PA-S450 Bedienungsanleitung

Audiovox

Audiovox Menace PAS2150 Bedienungsanleitung

Audiovox

Audiovox Jensen Power JPA260 Bedienungsanleitung

Audiovox

Audiovox Jensen PS475 Bedienungsanleitung

Audiovox

Audiovox XTM-600 Bedienungsanleitung

Audiovox

Audiovox AMP-590A Bedienungsanleitung

Audiovox

Audiovox Rampage AMP-602 Bedienungsanleitung

Audiovox

Audiovox Rampage AXT-240 Bedienungsanleitung

Audiovox

Audiovox Rampage AMP-592C Bedienungsanleitung

Audiovox

Audiovox Jensen PS1220M Bedienungsanleitung

Audiovox

Audiovox Rampage AXT-1200 Bedienungsanleitung

Audiovox

Audiovox AMP-596C Bedienungsanleitung

Audiovox

Audiovox Prestige PAB-1500D Bedienungsanleitung

Audiovox

Audiovox POWER PLUS Bedienungsanleitung

Audiovox

Audiovox Phase Linear UPA224 Bedienungsanleitung

Audiovox

Audiovox Prestige PAB-450R Bedienungsanleitung

Audiovox

Audiovox AMP-595C Bedienungsanleitung

Audiovox

Audiovox AXT-550 - Rampage Amplifier Bedienungsanleitung

Audiovox

Audiovox Rampage AXT-500 Bedienungsanleitung

Audiovox

Audiovox AMP-594 Bedienungsanleitung

Audiovox

Audiovox AMP-591A Bedienungsanleitung

Audiovox

Audiovox Prestige PAB-2100R Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung