Audiovox HR7008PKG Bedienungsanleitung

Installation Guide

128-8311

HR7008PKG

Two Specific Vehicle Headrests

With 7" LCD Monitors Touch Screen control

and Built-In

DVD Player for Rear Seat Entertainment

IMPORTANT

Installation of headrest products require careful planning and preparation. Be

extremely careful of seats that have airbags built into them. Keep wiring away from

any air bag wiring (usually identified by yellow connectors and yellow wire jackets).

Damage to air bag wiring can result in personal injury to vehicle occupants. If you

have any questions regarding wire routing or installation in a vehicle, please contact

Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation, insure that the

ACC wire is fused at the point where it is connected to the vehicle ACC wiring.

Failure to do so can result in damage to the vehicle if a short circuit develops

between the vehicle connection point and the mobile video product.

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to

the driver if the LCD panel or video monitor is used for vehicle information, system

control, rear or side observation or navigation. If the LCD panel or video monitor is

used for television reception, video or DVD play, the LCD panel or video monitor

must be installed so that these features will only function when the vehicle is in

"park" or when the vehicle s parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that

operates when the vehicle is in gear or when the parking is not applied must be

installed to the rear of the driver s seat where it will not be visible, directly or

indirectly, to the operator of the motor vehicle.

Licensed under one or more of the following patents:

Patent NOS. 7245,274 and 6,899,365

MATERIALS TO USE IN THIS PACKAGE:

1) HR7008PKG System Monitor

M1 Monitor with touch screen control and DVD Player (1pc)

M2 Monitor with touch screen control and DVD Player (1pc)

5) 8 Pin Din ~ 3 RCA Jack Conn

(P/N: 112-3658) – (1pc)

M1 M2

3) Wireless FMM Interface Box

(P/N 136-4658) – (1pc)

8) AUX CABLE

(P/N 112-3910) – (1pc)

4) 2 Pin DC Power Cable

(P/N 112-3667) (1pc)

2) Remote Control with

Wireless Game Controller

(P/N 136-4657) – (2pcs)

POWER

FMM

ON/OFF

SUBTITLE

DVD

SOURCE

DVD

MUTE

SYSTEM

RETURN

IRT

ON/OFF

SOURCE

AUTO

MEMORY

SKIP/

ERASEL

WRITE

123

456

78 9

EJECT

CHANNEL

SELECT

DAY

NIGHT PIX

AUDIO

REPEAT ZOOM A-B

MENU SETUP

M1 M2

DISPLAY

VOLUME

Front view =

Remote Control

Back view =

Wireless Game Controller

6) Extension Cable, 8 Pin Din to 8 Pin

Din Conn Green/Red (P/N 112-3944)

- (1pc)

7) Extension Cable, 8 Pin Din to 8 Pin

Din Conn Blue/Yellow (P/N 112-3945)

- (1pc)

Note :

M1 Monitor include master

monitor headrest cable

(P/N 112-3942)

& hardware screws

Note :

M2 Monitor include satellite

monitor headrest cable

(P/N 112-3943)

& hardware screws

HR7008PKG SYSTEM OVERVIEW

1) The HR7008PKG SYSTEM is a versatile audio / video system with built-in DVD player

HR7008M1/M2 which includes two touch screen monitors, that can accept an Audio /

Video input and independent AUX input. A separate audio output is provided for connecting

an optional FM Modulator to the vehicle's radio.

2) The M1 Monitor (HR7008M1) is comprised of a 7" touch screen TFT LCD monitor with

built-in DVD player that allows the user to select from the DVD/SD/USB, Source form M2,

AV input, Smart Port/AUX, and the Game source. The M1 monitor has a built-in infrared

audio transmitter (CH A) for use with the optional two-channel wireless headphones (CH

A).

3) The M2 Monitor (HR7008M2) is comprised of a 7" touch screen TFT LCD monitor with

build in DVD Player that allows the user to select from the DVD /SD/USB, Source from M1,

AV input and Smart Port. The M2 monitor has a built-in infrared audio transmitter (CH B)

for use with the optional two channel wireless headphones (CH B).

4) The monitors will show all of the functions with the comprehensive OSD and touch screen

UI OSD.

5) The optional two-channel wireless Headphone sets have an A-B switch that allow the user

to select the audio from either M1 (HR7008M1, CH A) or M2 (HR7008M2,CH B).

6) Using different IR codes, the M1 Monitor will only respond to the remote control unit when

the Monitor Select (M1) button on remote control is pressed. The M2 Monitor will only

respond to the Remote Control unit when the Monitor Select (M2) button on remote control

is pressed.

7) The wired headphones allow the user to listen to audio from the system.

8) The M1 (HR7008M1) and M2 (HR7008M2) Monitor will accept an audio / video input

through the 1/8" jack located on the front of the unit. The audio / video device could be a

video game system, video camera, or other input device.

SMART PORT

HR7008M1/HR7008M2

WIRED HEADPHONE

USBSMART

PORT

TOUCH SCREEN UI OSD

9) Pivot the screen until a comfortable viewing angle reached. The internal lock limits the

screen to a maximum adjustment of 19 degrees from closed position, the headrest itself

can be tilted forward to help achieve a comfortable viewing position.

10) Insert/Eject disc and SD Card

shaft angle

Inner Ring

Hook

Closed Position

SMART

PORT

PULL UP

USB

JACK

WIRED HEADPHONE

JACK

PUSH UP

19 degrees

Insert/Eject disc

Insert/Eject

SD Card

19 degrees

HR7008PKG

Monitor Unit

Electronics Installation Guide

HR7008M2

(Satellite Monitor)

HR7008M1

(Master Monitor)

HR7008 Monitor

(Satellite Monitor / M2)

HR7008 Monitor

(Master Monitor / M1)

Cable 1 :

Monitor Pigtail Cable

Cable 2 :

Headrest Cable

Peel backing off of double sided tape

(4 places) on vinyl tabs and stick to

plastic outer tray Match M1 monitor pigtail cable to M1 headrest cable

Match M2 monitor pigtail cable to M2 headrest cable

Hold the Eject Card then

press monitor and pull it

out.

Install Monitor Unit to Headress

Insert Eject Card at top slot

to the end.

6 8

With Screw (x4)

10 Move the locking tab to right position

to fully insert the monitor into the

headrest

11 12

Adjust match your vehicle

seatback dimension

VEHICLE PREPARATION:

1) Read the manuals and get familiar with the electrical requirements and

connections.

2) Prepare the vehicle by removing any interior trim necessary to gain access to the

vehicle's wiring as well as all areas where interconnecting wire harnesses will be

located. (Refer to the Installation Procedure). The mounting method, and the

location will vary from vehicle to vehicle, so this manual will only focus for the

installation of the HR7008PKG Master and Satellite Monitors in the supplied

configuration. The best location for the HR7008PKG System components is:

a. Monitors: Vehicle specific Headrest (NOTE: The Master Monitor should be

installed in the passenger position most used.)

b. FM Inter-Connect Box: Under either seat where monitors are located.

3) Locate an accessory power source (+12VDC present when the ignition key is in

the accessory and run positions. 0VDC should be present when the ignition key

is in the OFF position), and a good ground. Generally, these wires can be

located at the ignition switch or fusebox.

(NOTE: Ensure that the switched power is fused at the source. Failure to do so

may result in vehicle wiring damage.)

4) Run the wiring harnesses throughout the vehicle as necessary. (Refer to the

Wiring Diagrams on page 6, as well as the wiring instructions for the individual

components and accessory options being installed). Be sure, that all the wiring

is protected from sharp edges and is routed in such a manner that it will not be

pinched, when it is fully installed. Be sure to leave enough slack in the wiring at

each component to allow sufficient working room. Be sure to leave enough

slack in the monitor cables to allow the headrest to move up or down, and the

seat to move backward and forward.

5) Remove all the components from their packaging and then place them in the

vehicle at their respective locations.

6) Install the Headrests:

a. Remove vehicle's original Headrests.

b. Hold the HR7008PKG Headrest above the seat and insert the two cables

into the headrest support tube holes. Make sure that the headrest is in the

correct position (Display facing the rear).

c. Route the cables through the seat back and out the bottom of the seat.

d. Place the Headrest support tubes into the support tube holes while pulling

the cables to remove the slack. Be sure to leave enough slack in the monitor

cables to allow the headrest to move up or down.

7) Connect all the components together (electrically) and verify proper operation of

all the system functions.

A) The headrest DIN cables and the FMM inter-connect box DIN cables are color

coded. Connect each headrest cable to the correct color cable on the FMM

inter-connect box. In some vehicles it will be necessary to use the supplied DIN

extension cables to reach from under one seat to the other seat. The DIN

extension cables can be used for either the M1 or M2 monitors. The extension

cables are labeled M1-M2 A and M1-M2B, and are not color coded. When

connecting the extension cables, ensure that the A extension cable is used with

the A monitor cable and the B extension cable is used with the B monitor cable.

B) Extend the wireless FM antenna to its full length and orientate for best

reception. Do not place it on the FMM inter connect box.

C) Connect the DC power jack.

8) After verifying the proper operation of the system cover all of the DIN connectors

with the DIN connector covers and proceed to mount each component.

9) When all the components are mounted, recheck the entire system to be sure it is

functioning correctly. Make sure that no wiring was pinched, or connected

improperly during the final installation.

Wireless FM Modulator

The HR7008PKG is equipped with a built-in wireless FM Modulator*, that allows

you to listen to the DVD audio signal by tuning your vehicle's radio to the selected

frequency,

. This feature is accessed by using the FM

transmitter buttons on the remote (ON/OFF, Channel Select).

Whenever the FM modulator is on, broadcast reception on the vehicles radio will

be poor Switching off the FM modulator will allow normal radio reception.

*Note: In certain areas where there are a large number of FM radio stations (e.g. large

cities, urban areas), the reception of the FM signal may not be satisfactory, resulting in

static, distorted sound or signal bleed thru from strong local radio stations. This is not a

defect in the product, but the result of a stronger local radio station overpowering the

wireless FM transmitter in your overhead pod.

If wireless reception is unsatisfactory, an optional wired relay box (Audiovox P/N

SIRSWB) can be installed which will improve audio quality. Please contact the installer

if this is the case with your product.

(CH1 88.1MHz, CH2 88.3MHz, CH3 88.5MHz, CH4 88.7MHz, CH5

88.9MHz, CH6 89.1MHz, CH7 89.3MHz, CH8 89.5MHz, CH9 89.7MHz, CH10

89.9MHz, CH11 90.1MHz, CH12 90.3MHz, CH13 90.5MHz, CH14 90.7MHz,

Ch15 90.9MHz, CH16 91.1MHz)

HR7008PKG WIRING DIAGRAM

INTERFACE BOX

FM ANTENNA

M1 MonitorM2 Monitor

DIN Extension Cables

Master Monitor

Satellite Monitor

2 PIN DC POWER CABLE

AV Output

AV Input

Antenna for wireless FM MOD

See antenna note below

Optional

GREEN RED

YELLOW

BLUE

Andere Handbücher für HR7008PKG

Andere Audiovox Auto-Videosystem Handbücher

Audiovox

Audiovox VM9414 Bedienungsanleitung

Audiovox

Audiovox VME 9312 TS Bedienungsanleitung

Audiovox

Audiovox HR7011PKG Bedienungsanleitung

Audiovox

Audiovox VOD10 - Car - Overhead LCD Monitor Bedienungsanleitung

Audiovox

Audiovox Mobile Video 128-8565A Bedienungsanleitung

Audiovox

Audiovox VOD8521 - DVD Player / LCD Monitor Bedienungsanleitung

Audiovox

Audiovox VOD85 - DVD Player With LCD Monitor Bedienungsanleitung

Audiovox

Audiovox VBP4000 - VBP 4000 DVD Player Bedienungsanleitung

Audiovox

Audiovox VOD1048 Bedienungsanleitung

Audiovox

Audiovox VOH641A Bedienungsanleitung

Audiovox

Audiovox VOD1023 - 10.2 Inch Dropdown Mobile Video... Bedienungsanleitung

Audiovox

Audiovox VOD1048 Bedienungsanleitung

Audiovox

Audiovox VOD710 - DVD Player With LCD Monitor Bedienungsanleitung

Audiovox

Audiovox VOD705DL - DVD Player With LCD Monitor Bedienungsanleitung

Audiovox

Audiovox PROV715 Bedienungsanleitung

Audiovox

Audiovox DVD1627 Planungshandbuch

Audiovox

Audiovox VOH802 - VOH 802 - LCD Monitor Bedienungsanleitung

Audiovox

Audiovox VOD701 Bedienungsanleitung

Audiovox

Audiovox VOH1041DL Bedienungsanleitung

Audiovox

Audiovox Movies 2 Go AVXMTGHR1M Technisches Datenblatt

Audiovox

Audiovox Rampage VBP1000S Bedienungsanleitung

Audiovox

Audiovox PAV1510DTV Handbuch

Audiovox

Audiovox AVXMTG10U Bedienungsanleitung

Audiovox

Audiovox LCM1502TV Bedienungsanleitung

Beliebte Auto-Videosystem Handbücher anderer Marken

Stinger

Stinger HEIGH10 RB10RAM13B Bedienungsanleitung

Eonon

Eonon E1057 Bedienungsanleitung

Milion

Milion D2223 Bedienungsanleitung

Metra Electronics

Metra Electronics 99-8153 Bedienungsanleitung

Voxx Electronics

Voxx Electronics HR8MA1 Bedienungsanleitung

Axxera

Axxera AV604Bi Bedienungsanleitung

Clarion

Clarion NX706E Bedienungsanleitung

Pyle view

Pyle view PLDN74BTi Bedienungsanleitung

Clarion

Clarion NX602 Bedienungsanleitung

PowerAcoustik

PowerAcoustik PTID-5850N Bedienungsanleitung

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Benutzerhandbuch

Lanzar

Lanzar SVDVD5 Bedienungsanleitung

Kia

Kia MTXM100YPPE Bedienungsanleitung

Eonon

Eonon E1060 Bedienungsanleitung

Macrom

Macrom M-AN900 Bedienungsanleitung

Hyundai

Hyundai BAPE-L3000N Bedienungsanleitung

r.LiNK

r.LiNK RL2-UCON8-SM Bedienungsanleitung

Blaupunkt

Blaupunkt DVP 01C Bedienungsanleitung