Audiovox PROFESSIONAL Series Bedienungsanleitung
12010AudiovoxElectronicsCorporation.Allrightsreserved.
PROFESSIONAL
SERIES
Remote Start with Keyless Entry
Installation Guide
CA6150RX
2 2010AudiovoxElectronicsCorporation.Allrightsreserved.
Before You Begin ...................................................................................... 3
Wire Connection Guide ...........................................................................4
8 Pin Main Harness ...................................................................................5
3 Pin Parking Light Harness .....................................................................8
6 Pin Start Harness ...................................................................................8
4 Pin Auxiliary Harness ..........................................................................10
2 Pin Door Lock Output Harness ........................................................... 11
Additional Ports ...................................................................................... 15
Antenna / LED / Programming Port .......................................................15
DBIPort....................................................................................................15
Tracking Port ...........................................................................................15
Set Up & Programming.......................................................................... 16
Transmitter Programming ........................................................................16
Manual Feature Programming.................................................................16
Programming Feature Banks ..................................................................17
Tach Programming ..................................................................................18
Smart Tachless.Mode .............................................................................18
Feature Descriptions .............................................................................19
Transmitter Button Functions .............................................................22
Remote Start Shutdown Diagnostics ................................................23
System Layout.........................................................................................24
Table of Contents
32010AudiovoxElectronicsCorporation.Allrightsreserved.
PROFESSIONALINSTALLATION
STRONGLYRECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Technical Support (800) 421-3209
or go to
http://techservices.codesystems.com
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE ATEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
Use grommets when routing wires through metal
surfaces
BEFORE YOU BEGIN
4 2010AudiovoxElectronicsCorporation.Allrightsreserved.
6 Pin Start Harness
4 Pin Auxiliary Output Harness
8 Pin Main Harness
3 Pin Parking Light Harness
52010AudiovoxElectronicsCorporation.Allrightsreserved.
2 Pin Lock Output Harness
1 VIOLET/BLACK AUX 1
This wire provides a ( - ) 500mA output capable of driving relays. For Control of
optional accessories (i.e. Power Window/Sunroof, etc.).
To activate refer to the transmitter button configuration chart. Please refer to the
selectable options for timing.
8 Pin Main Harness
2 BLACK/WHITE ILLUMINATEDENTRYOUTPUT( -)
This wire provides a ( - ) 500mA output for 30 seconds when the system is
disarmed capable of driving relays.
Locate the vehicle’s dome light or pin switch wire.
Verification: This wire will register positive voltage or ground when the
vehicle's dome light is turned ON.
3 BROWN/BLACK HORNOUTPUT(- )
Locate the vehicle’s horn wire.
Verification: This wire will register at positive voltage and register
ground when the horn switch is pressed.
Connect the BROWN/BLACK wire to the vehicle’s horn wire. This is a low current
output, 500mA.
6 2010AudiovoxElectronicsCorporation.Allrightsreserved.
Fused +12 Volt
Battery Source
30
87
87a
86 85
BLUE/BLACK ActiveOutput
Wire
VATS Control Module
Matching Value
Resistor
Ignition Switch
VATS Wire #1, WHITE or WHITE/BLACK
VATS Wire #2, WHITE or VIOLET/WHITE
X CUT
GM VATS
Fused +12 Volt
Battery Source
30
87
87a
86 85
BLUE/BLACK Active Outpu
t
Wire
To Vehicle's 2nd or
3rd Ignition Wire
Jump To PINK
Ignition Output
Wire From
Control Module
Ignition 3 Accessory 2/
3
Fused +12 Volt
Battery Source
30
87
87a
86 85
BLUE/BLACK Active Outpu
t
Wire
To Vehicle's 2nd or 3rd
Accessory Wire
Jump To ORANGE
Accessory Output
Wire From
Control Module
4 RED/WHITE TRUNKRELEASE OUTPUT (-)
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when
the trunk release is activated.
This is a low current output, 500mA.
5 BLUE/BLACK IGNITION3 /ACTIVEOUTPUT(- )
The Active Output/Ignition 3 output wire provides a ground output when the remote
start function is activated and remains until 4 seconds after the remote start is
shutdown. The Ignition 3 output wire can be used for several functions listed
below. If this wire will be used for multiple application's a 1 amp diode is required
in-line with the stripe facing the control module.
Factory transponder (coded key) bypass.
General Motors VATS bypass, see the following diagram. Use an SPDT relay (not
supplied).
Ignition 3 output, see the following diagram. Use an SPDT relay (not supplied).
Accessory 2/3 output, see the following diagram. Use an SPDT relay (not
supplied).
72010AudiovoxElectronicsCorporation.Allrightsreserved.
6 PURPLE/WHITE TACHINPUT
Locate the vehicle’s ignition coil or fuel injector in the engine compartment.
Verification: Test using the following procedure:
1. Set voltmeter to AC VOLTS.
2. Attach positive lead of a volt meter to a constant 12-volt source.
3. Attach negative lead of a volt meter to the wire to be tested.
4. Start the engine.
5. Have someone press on the gas pedal slightly as you monitor the meter. If
connected to the correct wire, the voltage reading will increase as the engine’s
RPM increases.
Connect the PURPLE/WHITE wire to the negative side of the vehicle ignition coil
or fuel injector.
7 GRAY HOODPIN INPUT (- )
Install a Hood Pin Switch and connect to the GRAY wire. This connection is
required for Remote Start.
Verification: This wire when connected will register ground when the
vehicle's hood is opened.
Connect the GRAY wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
8 BROWN/RED BRAKE INPUT ( + )
Locate the vehicle’s brake light wire at the brake pedal mounted switch.
Verification: This wire registers positive voltage when the brake pedal is
pressed.
Connect the BROWN/RED wire to the vehicle’s brake light wire.
8 2010AudiovoxElectronicsCorporation.Allrightsreserved.
6 Pin Start Harness
1 PURPLE STARTER OUTPUT( +)
Locate the vehicle starter wire.
Verification: This wire registers voltage only when the key is turned to the
START position.
Verification:
The starter wire registers voltage when the key is turned to the
START position.
Connect the PURPLE wire to the vehicle starter wire.
1 BLACK GROUND
Connect the BLACK wire to a solid chassis ground point using a ring terminal and
self tapping screw (not supplied). Scrape away paint from the grounding point to
ensure a good connection. The recommended grounding point is a metal surface
in the driver’s side kick panel area.
NOTE: Do not ground the BLACK wire with any other vehicle components.
3 Pin Parking Light Harness
2 WHITE/RED PARKING LIGHT INPUT
3 WHITE PARKINGLIGHTOUTPUT
Locate the parking light output wire at the vehicle’s light switch.
Verification: This wire registers positive voltage when the parking lights are
turned on.
Positive switching Parking Lights:
Connect the WHITE/RED wire to a 15 Amp max fused battery source.
Connect the WHITE wire to the parking light output wire.
Negative switching Parking Lights:
Connect the WHITE/RED wire to a good chassis ground.
Connect the WHITE wire to the parking light output wire.
92010AudiovoxElectronicsCorporation.Allrightsreserved.
2 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
3 ORANGE ACCESSORY 1 ( + )
Locate the vehicle’s accessory wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to ACC
(Accessory) and the ON (or RUN) position. The voltage drops out when the
key is turned to the START(or CRANK) position.
Connect the ORANGE wire to the vehicle’s accessory wire.
4 PINK/WHITE IGNITION 2 ( + )
Locate the vehicle’s 2nd ignition wire at the ignition switch (if equipped).
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position, but not the ACC (Accessory) position. The voltage does not
drop out when the key is turned to the START(or CRANK) position.
Connect the PINK/WHITE wire to the vehicle’s ignition 2 wire.
Programmable output: IGN, ACC, Start.
5 RED BATTERY 12V ( + )
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register ( + ) voltage in all positions of the ignition
switch.
Connect the RED wire to the constant 12 Volt battery wire.
NOTE: Remove all fuses until all connections are made.
10 2010 Audiovox Electronics Corporation. All rights reserved.
3 GREEN/WHITE FACTORYARM /
PULSEAFTER SHUTDOWN ( -)
This wire will supply a ( - ) 500mA pulse both upon arming the system and after
the remote start shuts down. This is typically used to re-lock the vehicle’s doors if
they unlock upon remote start shutdown. It can also be used to pulse a door pin-
switch wire to prevent the vehicle’s accessories from remaining on after remote
start shutdown.
6 PINK IGNITION1(+)
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or
RUN) position. The voltage does not drop out when the key is turned to the
START(or CRANK) position.
Connect the PINK wire to the vehicle’s Ignition wire.
This wire is also used for Ignition 1 Output.
4 Pin Auxiliary Output Harness
1 LT GREEN/BLACK FACTORY DISARM /
PULSE BEFORE START ( - )
This wire will supply a ( - ) 500mA pulse both upon disarming the system and when
the remote start feature is activated. Locate the factory perimeter alarm disarm
wire from the key cylinder inside the drivers door.
Verification: This wire registers ground if the key is turned to the unlock
position in the driver’s door cylinder.
Connect the LIGHT GREEN/BLACK wire to the factory alarm disarm wire.
2 LTBLUE PULSEAFTER START (- )
This wire will supply a ( - ) 500mA pulse upon successful completion of the remote
start activation sequence and is typically used to re-lock the vehicle’s doors upon
remote start if necessary.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Audiovox Fernstartsystem Handbücher
Audiovox
Audiovox PurSuit PRO9056C Bedienungsanleitung
Audiovox
Audiovox AX-45 Bedienungsanleitung
Audiovox
Audiovox AA-RS20CS Bedienungsanleitung
Audiovox
Audiovox Patinum APS-997 Bedienungsanleitung
Audiovox
Audiovox Pursuit PRO-9051 Bedienungsanleitung
Audiovox
Audiovox AS9233ST Bedienungsanleitung
Audiovox
Audiovox AA-RS10CS Bedienungsanleitung
Audiovox
Audiovox Prestige APS-55TW Bedienungsanleitung
Audiovox
Audiovox Pursuit PRO-9556 Bedienungsanleitung
Audiovox
Audiovox Prestige 128-7852A Bedienungsanleitung
Audiovox
Audiovox APS620 - Prestige Remote Start Bedienungsanleitung
Audiovox
Audiovox Pursuit PRO 9171FT Bedienungsanleitung
Audiovox
Audiovox APS687 - Car Prestige Remote Start Bedienungsanleitung
Audiovox
Audiovox Pursuit PRO-9275 Bedienungsanleitung
Audiovox
Audiovox AS 9076N Bedienungsanleitung
Audiovox
Audiovox Prestige Platinum+ APS 686 Bedienungsanleitung
Audiovox
Audiovox AS 9075a Bedienungsanleitung
Audiovox
Audiovox PurSuit PRO-9056TW Bedienungsanleitung
Audiovox
Audiovox car connection 2.0 Bedienungsanleitung
Audiovox
Audiovox PRO-9556C Pursuit Series Bedienungsanleitung
