AUSTRALIAN MONITOR DCM500 - Bedienungsanleitung

500W AC/DC Power Amplifier

DCM500

Description

The DCM500 is a high performance 500 watt power amplifier designed to meet the needs of

the most demanding sound reinforcement installations and applications. The amplifier is

designed to operate from both AC mains power as well as 24 volts DC.

Inputs and Outputs

The DCM500 features a transformer balanced line level XLR input with a parallel output to

feed additional power amplifiers. The DCM500 provides 100 volt, 70 volt and 4 ohm speakers

outputs via a rear panel barrier strip.

Controls and Metering

The front panel consists of a mains power switch and a recessed, screwdriver adjustable input

attenuation control. The front panel of the DCM500 includes a back-lit LED display indicating

power, high temperature, LED VU meter and mains fail indication. The mains fail indicator will

only operate in the event of a mains power failure and when the amplifier is connected to a

24V DC power supply.

Protection

The DCM500 features a slow start function as well as overload and overdrive protection.

Should the amplifier be overdriven, a current limiter will protect the unit, and in a worst case

scenario the amplifier will shut down until the problem is resolved. Once the problem is fixed

(shorted speaker line, or overdriven input), the amplifier will automatically reset and continue

operation. The amplifier also features a built-in compressor/limiter designed to smooth out

any peaks in input signal. The DCM500 features generous heatsinking and fan cooling. The fan

will only switch on if the operating temperature exceeds a factory preset level.

Australian Monitor Installation Series amplifiers feature a protection network that provides

greater stability and performance. Our amplifiers are recognised

worldwide for their reliability and this is due to the extensive levels of

current limiting which protect the amplifiers from both overload and

overdrive conditions.

Other Features

The DCM500 can operate from both AC and 24V DC and includes a built-in trickle charge

circuit.

Power Output 500 Watts RMS into 100 & 70 Volt line or 4 Ohms

Maximum Load 20 Ohms @ 100V

Frequency Response 50Hz - 15kHz (± 3dB) into 100V

Total Harmonic Distortion Less than 0.5% @ 1kHz; Distortion at Max Power: 0.7%

Signal To Noise Ratio -82dB

Input Sensitivity Max 300mV (set @ 1V)

Input Impedance 10K Ohms

Input Connection Transformer Balanced input with male and female XLR input/output sockets

Outputs 100 & 70 Volts or 4 Ohm speaker outputs via a rear panel barrier strip. Line out to feed

additional power amplifiers available from 1 of the paralleled XLR inputs

Controls Front Panel Power Switch, Recessed front panel input attenuator

Metering/Indicators Amplifier Status Display Window including: Power On LED;

10 segment LED output meter; Mains fail LED; High temp trip LED

Power Sources AC: 240V - 50Hz or 110V - 60Hz 3 pin IEC connector;

DC: 24V with built in trickle charge circuit: 300ma maximum trickle charge

30 Amp maximum current draw on DC 300ma standby (idle) current draw on DC

Power Consumption 800 Watts (maximum)

Protection Internal Cooling Fan with temperature sensor

Compressor/Limiter Current Limiter with auto protect and auto reset

Dimensions/Weight 88mm H x 483mm W x 410mm D (Chassis dimensions only). 18 kg

Engineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (ABN 78 001 345 482), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia

NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233

TAS Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Fax: (08) 8352 4488 Export Enquiries: [email protected] Website: www.australianmonitor.com.au

ARCHITECTURAL AND ENGINEERING SPECIFICATIONS

The power amplifier shall be of high quality, suitable for the most demanding PA installations and appli-

cations. The unit shall have a frequency response of no less than 50Hz - 15kHz (±3dB). Distortion at

1kHz shall not exceed 0.5%. The Signal to Noise ratio shall be -82dB or greater. The amplifier shall have

two transformer balanced XLR inputs, one of which can be used to feed additional power amplifiers.

The amplifier shall be capable of delivering 500 watts RMS into 100 & 70 volt or 4 ohm loads. Speaker

connection shall be via a rear panel barrier strip.

The unit shall operate from both AC mains power or from a 24V DC battery supply. The amplifier shall

include a built-in trickle charge circuit. The amplifier shall feature overload and overdrive protection and

shall also include cooling fans, which should only be active if the operating temperature exceeds a fac-

tory preset level.

The unit shall be packaged in a rugged 2 RU metal chassis suitable for desk or rack mounting.

The power amplifier shall be an Australian Monitor Installation Series model DCM500.

Andere Handbücher für DCM500 -

Inhaltsverzeichnis

Andere AUSTRALIAN MONITOR Verstärker Handbücher

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS 120 Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS26 Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMC120 Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS120 Series Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR ACM120XL Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR ACM250P Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMC120 Bedienungs- und Montageanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMD2100P Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR SY400V SY800V Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS1202P Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR IC30 Series Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR PA1200. Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR IS600 Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS120XL Series Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS250P Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMD2200P Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS120XL Series Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS250 Series Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR HS250P Kurzanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMC+250 Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AM1600 Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR AMIS120 Series Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR K SERIES - Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR Digipage JR Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung