autocom WIRE3 Bedienungsanleitung
Autocom Communications
Tecstar Electronics Ltd, Bramley Road, St Ives, Cambridgeshire, PE27 3 S England.
Telephone: +44 (0)1480 494444
Fax: +44 (0)1480 399502
Email: [email protected]
ebsite: www.autocom.co.uk
All Autocom products are under warranty for a period of
12 months from the date of original purchase, to the original
purchaser, from an authorised Autocom retailer. This warranty covers
faulty materials or workmanship, subject to the goods being used only as
stated, and only for the purpose as described in the instruction manuals. This
does NOT apply to goods where they are used for any other purpose or in any other
way than is explained in the instructions. Nor where the goods have been subjected to
misuse, neglect or accidental damage, or used with any other vendor’s products, including
incorrect mechanical or electrical installation, or where the goods have been repaired, modified
or altered, without the manufacturer’s written authorisation.
The manufacturer's warranty is limited to the goods being returned pre paid to the manufacturer's
factory, with the original packaging and the original proof of purchase date. The goods must be intact for
our examination.
here goods are accepted by the manufacturer, under the terms of the warranty
here the manufacturer, under the terms of the warranty, accepts goods, they will be repaired free of
charge or replaced (at the option of the manufacturer). here the goods are returned as faulty and are
found not to be, a charge will be payable to cover costs of inspection, testing, packing and return postage.
This warranty does not cover any consumable items such as batteries, replaceable hygiene foam coverings
for speakers and microphones, or any other items that are described within the instruction manuals as
being a consumable.
The manufacturer's warranty does not affect your statutory rights.
We service what we make
For details of Autocom’s International distributors and support network, please see our
website. Please contact your supplier or Autocom for any further help or information.
UK Manufacturer and Distributor
MA UFACTURERS
12 MO TH
WARRA TY
I STRUCTIO
MA UAL
It is very important that you fully read and understand all of
these instructions before installation and use.
These parts are designed for domestic motorcycle use.
WIRE3
Bluetooth Module wireless Helmet Interface
For use with all 7pin headset Autocom systems
WIRE3-A
WIRE3
WIRE3 Manual v1.qxd 13/7/11 4:21 pm Page 1
You are required to pair the IRE3 with your helmet Bluetooth headset devices before using it.
Step 1: The IRE3 module must be connected to Autocom headset connector and powered ON before
initiating pairing, this is indicated by a slow flashing blue led. To initiate pairing, press the pairing button
until the blue indicator of IRE3 is flashing quickly.
Step 2: Ensure there are NO other Bluetooth devices powered ON in the immediate area.
Step 3: Initiate the pairing process on your headset device. Refer to the manual of the device for details
of this process.
The pairing process may take up to 1 minute.
Note:
1. If the headset is not in pairing mode, your IRE3 won't find the headset.
2. hen put into pairing mode any existing pairing will be deleted.
3. You may need to repeat steps 1 to 3 until pairing succeeds.
4. Pairing is a process of associating Bluetooth devices with each other. It will establish a permanent
security link between the devices and enable quick access to the services provided without the need to
enter passkeys
5. Paired devices remain paired even when the devices are not powered on.
PAIRI G THE WIRE3 MODULE
AUDIO CO ECTIO - BLUETOOTH TO U IT
Headset Connection:
7pin DI systems:
Connect the BLACK 7-pin DIN plug to the Autocom Headset connection.
Connecting to Rider or Passenger as required.
WIRE3
WIRE3
1
The unit requires a 12V vehicle supply it has a built-in voltage regulator, and reverse input protection ,
so that it is safe to use directly from a vehicle’s switched and fused supply. A power cable is supplied
along with a fitting kit.
The 12V supply must be ignition switched, so that the IRE3 supply is off when the vehicle ignition if
OFF else the vehicle battery may be drained.
The DIN headset plug cable must be plugged into the Autocm, this provides the 0V connection.
For use with Super Pro Auto:
The IRE3 module has a 1.3mm power plug, when used with a Super Pro Auto this plugs directly into the
Bluetooth Power socket on the front of the unit, see (picture 1).
For use with othet modules:
hen used with other modles remove the power plug, and make electrical connection to the power (+ve)
RED wire to the Autocom by means of a splice connection using the tap splice terminal provided, as shown
below.
POWERI G THE WIRE3 MODULE
To 12V
Supply
cut
Power plug is inserted
in to Super Pro Power Socket
The Autocom IRE3 module is designed to allow cordless and automatic operation of
bluetooth compatible helmet devices with the Autocom unit.
Installation instructions must be followed carefully.
Installations must only be undertaken by a person who has a full understanding of the
electrical, safety and mechanical requirements involved. If in any doubt, please consult your
dealer.
The unit must be operated from a switched vehicle 12V DC supply. The unit is water-resistant
but not waterproof so care must be taken to keep it dry. Care must be taken not to mount the
unit near areas which will get hot, for example, near the engine or exhaust. Also the unit
must not be placed close to the ignition system; HT leads coil, alternator, or parts of the bike
that could cause electrical interference.
THE BLUETOOTH MODULE
U IT I STALLATIO
WIRE3
WIRE3
WIRE3 Manual v1.qxd 13/7/11 4:21 pm Page 3
Andere autocom Adapter Handbücher
