Revised 11/19/99 • BACview2Hardware Guide 4 © 1999 Automated Logic Corporation
3. Use the rear mounting plate as a template
to drill four mounting holes onto a panel
directly above the module the BACview2
will communicate with.
4. Feed the ribbon cable through the ribbon
hole on the rear mounting plate.
5. Pull the ribbon cable to the side and
mount the rear mounting plate onto the
panel using the four mounting holes
shown in Figure 2 on page 3. Be sure not
to bend or pinch the ribbon cable beneath
the rear mounting plate.
6. Connecttheribboncabletothefaceofthe
BACview2.
7. Reattach the BACview2to the rear
mounting plate.
8. Connect the ribbon cable to the module’s
Auxiliary Device port (see Figure 3).
Type II Mounting
The BACview2canbemountedonthedoorof
a panel box. With this type of mounting the
ribbon cable is fed through the door and
connected to the module (see Figure 4 on
page 5).
1. Remove the rear mounting plate screws
(see Figure 2 on page 3 for location) from
the BACview2.
2. Remove the rear mounting plate from the
BACview2.
3. Use the rear mounting plate as a template
to drill four mounting holes through the
door of a panel box.
4. Use the rear mounting plate as a template
to cut a hole for the ribbon cable through
thedoorofapanelbox.
5. Feed the ribbon cable through the ribbon
hole on the rear mounting plate and the
panel door.
6. Mount the rear mounting plate onto the
panel using the four mounting holes
showninFigure2onpage3.Besurenot
to bend or pinch the ribbon cable beneath
the rear mounting plate.
7. Connecttheribboncabletothefaceofthe
BACview2.
8. Reattach the BACview2to the rear
mounting plate.
9. Connect the ribbon cable to the module’s
Auxiliary Device port mounted inside the
panel box (see Figure 4 on page 5).
BAC v i e w 2Wiring
CAUTION The BACview2is a Class 2 device
(less than 30 VAC, 100VA max). Take
appropriate isolation measures when
mounting a BACview2in a control panel
where Class 1 devices or wiring are present.
1. Turn off the power to the module the BACview2will communicate with.
Figure3.TypeIMounting
Type:0320
Cat.#
MODULE
I/O
Expansion
A - Input Signal
B - G nd/Loop Pow er
I/O
Expansion
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
IN9
IN10
IN11
IN12
IN13
IN14
IN15
IN16
IN24
IN23
IN22
IN21
IN20
IN19
IN18
IN17
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
IN 32
IN 31
IN 30
IN 29
IN 28
IN 27
IN 26
IN 25
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
0-20mA
0-5Vdc
Therm isto r
/
dry contact
On Off
Gnd
24V ac
Class 2
24 V ac , 5 0- 6 0 H z
35 VA , 1.5A
Use Copper
Conductors Only
A
B
A
B
A
B
A
B
A
B
A
B
A
B
A
B
Run Error
Control Module
Power
Access
Port
Rx
Net
+
Net
-
Optional
Shield
Tx
Auxilary
Device
Port
CMnet
Universal Input
1- 16
Mode Select
0-20mA
0-5Vdc
Thermistor
/
dry contact
Universal Input
17-32
Mode Select
Module
Address
Arc156
R
LISTED
88FO
OpenEnergy
Mana gem ent Equ ipmen t
R
LISTED
88FO
C
CMnet Mode
Use Single Class 2
Source Only
9600/38.4k
