Automationdirect.com Productivity 2000 P2-15TD1 Bedienungsanleitung

3.3-24VDC SINK OUT

24V



Sales 800-633-0405 www.productivity2000.com 1

Output Specifications ............................................... 1

Application Notes ..................................................... 1

Module Installation ................................................... 2

QR Code .................................................................. 2

Hot Swap Information............................................... 2

Wiring Options.......................................................... 3

Wiring Diagram and Schematic................................ 3

Warning .................................................................... 4

Removable Terminal Block

Specifications ........................................................... 4

General Specifications ............................................. 4

Warranty: Thirty-day money-back guarantee. Two-year limited replacement.

(See www.productivity2000.com for details).

Terminal Block sold separately, (see wiring options on page 3).

P2-15TD1 Sinking DC Output

The P2-15TD1 DC Output Module

provides fifteen outputs that sink up to

1A per output from loads powered from

3.3–24 VDC supplies for use with the

Productivity2000 System.

Output Specifications

Outputs per Module 15 sinking

Output Type N-channel MOSFET, open drain

Rated Voltage 3.3–24 VDC

Operating Voltage Range 2.8–30 VDC

Maximum Output Current 1A per point / 8A per common

Minimum Load Current 1mA

Maximium Leakage Current 0.3 mA @ 30VDC

On Voltage Drop 0.18 VDC @ 1A

Maximum Inrush Current 4A for 40ms, 6A for 10ms

OFF to ON Response ≤0.5ms

ON to OFF Response ≤0.5ms

Status Indicators Logic Side (15 points)

Commons 2 non-isolated

Recommended External Fuse None

External Power Supply Required 12–24 VDC (-15% / +20%) @ 22mA

www.productivity2000.com Tech Support 770-844-4200

1 Align

with slot

2rotate

to seated

position

Module Installation

WARNING: Do not apply field power until

the following steps are completed. See

hot-swapping procedure for

exceptions.

WIRE STRIP

LENGTH

WIRE STRIP

LENGTH

Step One: Align module

catch with base slot and

rotate module into

connector.

Locked Unlocked

Step Two: Pull top locking

tab toward module face. Click

indicates lock is

engaged.

Step Three: Attach field wiring using the removable

terminal block or ZIPLink wiring

system.

QR Code

Important Hot-Swap Information

The Productivity2000 supports hot-swap! Individual

modules can be taken offline, removed, and replaced

while the rest of the system continues controlling your

process. Before attempting to use the hot-swap feature,

be sure to read the hot-swap topic in the programming

software’s help file or our online documentation at

AutomationDirect.com for details on how to plan your

installation for use of this powerful feature.

Use any QR Code reader application

to display the module’s product insert.

Caution: If possible, remove field power prior to

proceeding. If not, then EXTREME care MUST be taken

to prevent damage to the module, or even personal injury

due to a short circuit from the live terminal block.

Wiring Diagram and Schematic

12345678910 11 12 1813 14 15 16 17

24V

12 - 24V

Single Power Source

12345678910 11 12 1813 14 15 16 17

24V

12 - 24VDC

Dual Power Source

3.3 - 24VDC

Sales 800-633-0405 www.productivity2000.com 3

12-24VDC

+12-24VDC

OUTPUT

INTERNAL MODULE

COM

DIGITAL

ISOLATION

Sink

QR Code

Wiring Options

1ZIPLink Feed Through Modules and Cables¹

0.5 m (1.6 ft) cable

1.0 m (3.3 ft) cable

2.0 m (6.6 ft) cable

ZL-RTB20

ZL-RTB20-1

ZL-P2-CBL18

ZL-P2-CBL18-1

ZL-P2-CBL18-2

Terminal Block with pigtail cable

1.0 m (3.3 ft) cable

2.0 m (6.6 ft) cable

ZL-P2-CBL18-1P

ZL-P2-CBL18-2P

3Screw Terminal Block only

P2-RTB

(Quantity 1)

4Spring Clamp Terminal Block only

P2-RTB-1

(Quantity 1)

5Accessories²

ZL-RTB-COM

TW-SD-SL-1

TW-SD-MSL-1

ZL-RTB20

ZL-RTB20-1

1.Cable + ZIPLink Module = Complete System

2. ZL-RTB-COM provides a common connection point for power or ground

www.productivity2000.com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com

WARNING: To minimize the risk of potential safety problems, you

should follow all applicable local and national codes that regulate

the installation and operation of your equipment. These codes vary

from area to area and it is your responsibility to determine which

codes should be followed, and to verify that the equipment, instal-

lation, and operation are in compliance with the latest revision of

these codes.

Equipment damage or serious injury to personnel can result

from the failure to follow all applicable codes and standards. We

do not guarantee the products described in this publication are

suitable for your particular application, nor do we assume any

responsibility for your product design, installation, or operation.

If you have any questions concerning the installation or opera-

tion of this equipment, or if you need additional information, please

call Technical Support at 770-844-4200.

This publication is based on information that was available at

the time it was printed. At AutomationDirect.com® we constantly

strive to improve our products and services, so we reserve the right

to make changes to the products and/or publications at any time

without notice and without any obligation. This publication may also

discuss features that may not be available in certain revisions of

the product.

General Specifications

Operating Temperature 0° to 60°C (32° to 140°F)

Storage Temperature -20° to 70°C (-4° to 158°F)

Humidity 5 to 95% (non-condensing)

Environmental Air No corrosive gases permitted

Vibration IEC60068-2-6 (Test Fc)

Shock IEC60068-2-27 (Test Ea)

Field to Logic Side Isolation 1800VAC applied for 1 second

Insulation Resistance >10MΩ@ 500 VDC

Heat Dissipation 1800mW

Enclosure Type Open Equipment

Module Keying to Backplane Electronic

Module Location Any I/O slot in a Productivity2000 System.

Field Wiring

Use ZIPLink Wiring System or removable terminal

block (not included). See “Wiring Options” on

page 3.

EU Directive

See the “EU Directive” topic in the Productivity

Suite Help File. Information can also be obtained

at: www.productivity2000.com

Connector Type (sold separately) 18 Position Removable Terminal Block

Weight 100g (3.5oz)

Agency Approvals

UL 61010-1 and UL 61010-2-201 File E139594,

Canada and USA

CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-

2-201 Safety)*

*Meets EMC and Safety requirements. See the D.O.C. for details.

Removable Terminal Block Specifications

Part Number P2-RTB P2-RTB-1

Number of

Positions 18 Screw Terminals 18 Spring Clamp Terminals

Wire Range

30–16 AWG (0.051–1.31 mm²)

Solid / Stranded Conductor

3/64 in (1.2 mm) Insulation Maximum

1/4 in (6–7 mm) Strip Length

28–16 AWG (0.081–1.31 mm²)

Solid / Stranded Conductor

3/64 in (1.2 mm) Insulation Maximum

19/64 in (7–8 mm) Strip Length

Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.

Screw Driver

Width 0.1 inch (2.5 mm) Maximum*

Screw Size M2 N/A

Screw Torque 2.5 lb∙in (0.28 N∙m) N/A

Document Name Edition/Revision Date

P2-15TD1-DS 2nd Ed. 9/5/2019

*Recommend Screw Driver TW-SD-MSL-1

Andere Automationdirect.com Steuereinheit Handbücher

Automationdirect.com

Automationdirect.com Productivity 2000 P2-32ND3-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Stride SIOL-EI8B Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08TD2S Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08DA-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-16TR Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-15TD1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com HX-ECOM Series Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-15TD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-04DA Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08DA-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16TA Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16DAL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08TAS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-SCM Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-04DAL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL06 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08TD2P Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08TD1S Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16DA-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-08TRS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-04DAL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16TR Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08TD1P Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-08TA Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung