Automationdirect.com Productivity 2000 P2-16NE3 Bedienungsanleitung

2000

Sales 800-633-0405 www.productivity2000.com 1

Document Name Edition/Revision Date

P2-16NE3-DS 2nd Ed. 9/10/2019

Input Specifications

Inputs per Module 16 (Sink/Source)

Operating Voltage Range 24 VAC/VDC

Input Voltage Range 20.4–27.6 VAC/VDC

Peak Voltage Range 27.6 VAC/ 30VDC

AC Frequency 47–63 Hz

Input Current (typical) 3.4 mA @ 24 VAC/VDC

Maximum Input Current 5.0 mA @ 27.6 VAC/VDC

ON Voltage Level > 12VDC, > 9VAC

OFF Voltage Level < 10.5VDC, < 9VAC

Minimum ON Current 2.5 mA

Maximum OFF Current 0.5 mA

OFF to ON Response DC: 6ms > max

AC: 10ms

ON to OFF Response DC: 10ms > max

AC: 20ms

Status Indicators Logic Side (16 Points)

Commons per Module 2 (8 points/common) Isolated

Warranty: Thirty-day money-back guarantee. Two-year limited replacement.

(See www.productivity2000.com for details).

Terminal Block sold separately, (see wiring options on page 2).

Input Specifications .................................................. 1

Module Installation ................................................... 2

Wiring Options.......................................................... 2

Wiring Diagram and Schematic................................ 3

QR Code .................................................................. 3

Hot Swap Information............................................... 3

Warning .................................................................... 4

Removable Terminal Block Specifications ............... 4

General Specifications ............................................. 4

P2-16NE3 AC/DC Input

The P2-16NE3 AC/DC Input Module provides

sixteen 24VAC or VDC sink/source inputs

for use with the Productivity2000 system.

www.productivity2000.com Tech Support 770-844-4200

1 Align

with slot

2rotate

to seated

position

Module Installation

WARNING: Do not apply field power until

the following steps are completed. See

hot-swapping procedure for

exceptions.

WIRE STRIP

LENGTH

WIRE STRIP

LENGTH

Step One: Align module

catch with base slot and

rotate module into

connector.

Locked Unlocked

Step Two: Pull top locking tab

toward module face. Click indi-

cates lock is

engaged.

Step Three: Attach field wiring using the removable

terminal block or ZIPLink wiring

system.

Wiring Options

1ZIPLink Feed Through Modules and Cables¹

0.5 m (1.6 ft) cable

1.0 m (3.3 ft) cable

2.0 m (6.6 ft) cable

ZL-RTB20

ZL-RTB20-1

ZL-P2-CBL18

ZL-P2-CBL18-1

ZL-P2-CBL18-2

Terminal Block with pigtail cable

1.0 m (3.3 ft) cable

2.0 m (6.6 ft) cable

ZL-P2-CBL18-1P

ZL-P2-CBL18-2P

3Screw Terminal Block only

P2-RTB

(Quantity 1)

4Spring Clamp Terminal Block only

P2-RTB-1

(Quantity 1)

5Accessories²

ZL-RTB-COM

TW-SD-SL-1

TW-SD-MSL-1

ZL-RTB20

ZL-RTB20-1

1.Cable + ZIPLink Module = Complete System

2. ZL-RTB-COM provides a common connection point for power or ground

QR CodeWiring Diagram and Schematic

24 VDC

24 VAC

24 VDC

24 VAC

12345678910 11 12 1813 14 15 16 17

Sales 800-633-0405 www.productivity2000.com 3

INPUT

COM

Internal Module Circuitry

Optical Isolator

24 VDC

Equivalent Input Circuit

24VAC

Important Hot-Swap Information

The Productivity 2000 supports hot-swap! Individual

modules can be taken offline, removed, and replaced

while the rest of the system continues controlling your

process. Before attempting to use the hot-swap feature,

be sure to read the hot-swap topic in the programming

software’s help file or our online documentation at

AutomationDirect.com for details on how to plan your

installation for use of this powerful feature.

Use any QR Code reader application to

display the module’s product insert.

Caution: If possible, remove field power prior to

proceeding. If not, then EXTREME care MUST be taken

to prevent damage to the module, or even personal injury

due to a short circuit from the live terminal block.

www.productivity2000.com Tech Support 770-844-4200 Sales 800-633-0405 www.productivity2000.com

WARNING: To minimize the risk of potential safety problems, you

should follow all applicable local and national codes that regulate

the installation and operation of your equipment. These codes vary

from area to area and it is your responsibility to determine which

codes should be followed, and to verify that the equipment, instal-

lation, and operation are in compliance with the latest revision of

these codes.

Equipment damage or serious injury to personnel can result

from the failure to follow all applicable codes and standards. We

do not guarantee the products described in this publication are

suitable for your particular application, nor do we assume any

responsibility for your product design, installation, or operation.

If you have any questions concerning the installation or opera-

tion of this equipment, or if you need additional information, please

call Technical Support at 770-844-4200.

This publication is based on information that was available at

the time it was printed. At AutomationDirect.com® we constantly

strive to improve our products and services, so we reserve the right

to make changes to the products and/or publications at any time

without notice and without any obligation. This publication may also

discuss features that may not be available in certain revisions of

the product.

General Specifications

Operating Temperature 0° to 60°C (32° to 140°F),

Storage Temperature -20° to 70°C (-4° to 158°F)

Humidity 5 to 95% (non-condensing)

Environmental Air No corrosive gases permitted

Vibration IEC60068-2-6 (Test Fc)

Shock IEC60068-2-27 (Test Ea)

Field to Logic Side Isolation 1800VAC applied for 1 second

Insulation Resistance >10MΩ @ 500VDC

Heat Dissipation 400mW

Enclosure Type Open Equipment

Module Keying to Backplane Electronic

Module Location Any I/O slot in a Productivity2000 System.

Field Wiring

Use ZIPLink Wiring System or removable terminal

block (not included). See “Wiring Options” on

page 2.

EU Directive

See the “EU Directive” topic in the Productivity

2000 Help File. Information can also be obtained

at: www.productivity2000.com

Connector Type (not included) 18-position removable terminal block

Weight 90g (3.2 oz)

Agency Approvals

UL 61010-1 and UL 61010-2-201 File E139594,

Canada and USA

CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-

2-201 Safety)*

*Meets EMC and Safety requirements. See the D.O.C. for details.

Removable Terminal Block Specifications

Part Number P2-RTB P2-RTB-1

Number of

Positions 18 Screw Terminals 18 Spring Clamp Terminals

Wire Range

30–16 AWG (0.051–1.31 mm2)

Solid / Stranded Conductor

3/64 in. (1.2 mm) Insulation Maximum

1/4 in. (6–7 mm) Strip Length

28–16 AWG (0.081–1.31 mm2)

Solid / Stranded Conductor

3/64 in. (1.2 mm) Insulation Maximum

19/64 in. (7–8 mm) Strip Length

Conductors “USE COPPER CONDUCTORS, 75°C” or Equivalent.

Screw Driver

Width 0.1 inch (2.5 mm) Maximum*

Screw Size M2 N/A

Screw Torque 2.5 lb·in (0.28 N·m) N/A

*Recommended Screwdriver TW-SD-MSL-1

Andere Automationdirect.com E/A-System Handbücher

Automationdirect.com

Automationdirect.com Productivity 200 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Stride SIO-MB04THMS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Stride SIO-MB08THMS Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16AD-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-07B Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08ADL-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16ADL-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16NA Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-04RTD Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-04AD Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-08NA Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-16AD-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-04ADL-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-32NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-15CDD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-16ND3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-08AD-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-4ADL2DAL-2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 2000 P2-06RTD Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-16NE3 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-4ADL2DAL-1 Bedienungsanleitung

Automationdirect.com

Automationdirect.com Productivity 1000 P1-04THM Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

M-system

M-system R3Y-RS8 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

WAGO

WAGO I/O SYSTEM 750 750-833 Bedienungsanleitung