Autrol APT 3000 Series Bedienungsanleitung

Quick Start Guide

APT 3000 Series

This manual covers mainly the functional needs for powering and configuring 3100 A/D/G/H &

3200 A/G series transmitters, including the 3100 MP & 3100 L/ 3200 L sealed assemblies.

For full instructions on installation, configuration and other features/option sets available with these trans-

mitters please read the full product manuals available under the download tab of

www.autroltransmitters.com.

Additional instructional videos outlining programming and configuration functionalities can also be found

on www.autroltransmitters.com. First time users are encouraged to make use of these support resources

made available at no cost online.

For additional technical support or advanced troubleshooting please contact your nearest Autrol office or

call 1-847-779-5000.

Getting Started

 Before installation check the model, specifications, and installation location for the transmitter. Install

using proper engineering practice.

 Mount transmitter securely and stabilize any impulse piping.

 Follow the published pressure and temperature limits for ordered transmitter and options.

 For process temperatures ≥212°F, use of adequate impulse lines, capillaries (diaphragm seals), or

cooling elements are recommended.

 Set Units, URL, and LRL (in menus 21, 22, and 23 respectively). See full menu tree at end of manual.

 After installation of a 3100 D/H/G or 3200 G always perform a Zero Trim (menu 11 - note this is not the

same as Zeroing). Ensure applied process to transmitter is zero before attempting Zero Trim.

 Do not perform Zero Trim for 3100 A/ 3200 A (absolute) unless a true zero PV can be applied to these

units. Instead a Zero Adjust (menu 12) is recommended.

 Zero Adjust is also recommended for 3100/ 3200 L (tank level application) to compensate for tank noz-

zle offsets.

Functional Block/Sensor Part Diagram

APT 3100

APT 3200

APT 3100 Dimensional Drawing

APT 3100 Exploded View

APT 3100 MP Dimensional Drawing

APT 3100 MP Exploded View

APT 3200 Dimensional Drawing

APT 3200 Exploded View

LCD Screen

The 5 digit LCD screen shows:

 Up to 5 digits of measured value

 Error code

 Units (Normal and Engineering)

 Menu and Menu Option

 Indication of being in Normal or Engineering mode

 Indication of output being Linear or Square Root

 Indication of performing a Loop Test

 Indication of being in Multi-Drop mode

Mode/Output

Up to 5 Digit

Display

Unit/ Error

Menu Option

The 5 digit LCD screen shows:

 Up to 5 digits of measured value

 Error code

 Units (Normal and Engineering)

 Menu and Menu Option

 Indication of being in Normal or Engineering mode

 Indication of output being Linear or Square Root

 Indication of performing a Loop Test

 Indication of being in Multi-Drop mode

LCD Screen Rotation

Unscrewing the two screws on either side of the LCD

screen allows for the screen to be rotated 90° clock-

wise or counterclockwise.

LCD Screen Display Error Codes

Fail-Mode

AUTROL® Smart Pressure Transmitters automatically perform real time self-diagnostic routines and

display any error codes on the local LCD (M1 option if ordered) that can be used for troubleshooting.

In addition to this, the self-diagnostic routines are also designed to drive transmitter current output

outside of the normal saturation values in case a fault mode is detected. The transmitter will drive its

current 4-20mA output low (down) or high (up) based on the position of the failure mode alarm jumper

(or DIP switch) configured in line with NAMUR requirements.

*For Blind units using DIP

switch on MCU board .

Fail Mode Selecon Jumper

Switch on LCD Module

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Autrol Sender Handbücher

Autrol

Autrol APT3200 Series Bedienungsanleitung

Autrol

Autrol APT3200 Series Bedienungsanleitung

Autrol

Autrol ATT Series Bedienungsanleitung

Autrol

Autrol APT3200 Series Bedienungsanleitung

Autrol

Autrol APT 3100 Series Bedienungsanleitung

Autrol

Autrol ALT-6100 Series Bedienungsanleitung

Autrol

Autrol APT 3100 Series Bedienungsanleitung

Autrol

Autrol ATT2100 Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung