Avantco A36869 Bedienungsanleitung

Attachment control switch pack 2016 2

Installation manual

Attachment control switch pack

Electric connectors for multi connector system

Electric socket adapters

A36869

A36679

Please read these instructions carefully before using or

assembling the equipment and follow all instructions.

For more information or assistance contact your nearest Avant

dealer or service point.

English

www.avanttecno.com

2 (8)

1. Introduction

Electric connector

All attachments with electric functions can be connected to the loader by using one of the folowing ways:

1. Use a separate cable kit with a switch, supplied with the attachment

2. Operate with Attachment control switch pack, with a separate electric socket on the loader boom

3. Operate with the new Attachment control switch pack, with the electric socket integrated in the multi

connector.

An adapter A36679 is supplied with all attachments delivered after January 1st 2016. This manual will

show how to install the adapter to the attachment connector.

Electric socket is integrated in the multi connector on all loaders equipped with attachment control

switch pack from January 1st 2016. The socket can be retrofitted to the loader multi connector with

adapter A36869.

This manual will also show how to fit the adapter to the loader connector.

1.1 In this manual

This manual will show:

How to fit an electric connectore to

the attachment multi connector, to

connect an attachment with electric

functions to the socket on the loader

connector.

All attachments delivered after

January 1st 2016, with electric

features, are equpped with the

adapter A36679.

How to upgrade the separate electric

socket of the attachment control

switch pack A34700 into the version

with electric socket integrated into the

multi connector

Adapter A36869 includes all

necessary components for

installation.

The adapter completes the Multi

connector system by adding a socket

on the lower right hole of the loader

multi connector, when seen from the

front of the machine.

All electric connections of the retrofit adapters for converting the separate socket next to the loader multi

connector to the integrated socket will be made with quick fittings, no electric wire work is needed.

3 (8)

1.2 Attachment control switch pack - Electric connector integrated in the

multi connector

Electric connection for attachment integrated into the multi connector system makes changing of an

attachment with electric functions even easier and quicker, as all hydraulic hoses and the electric harness of

the attachment are connected to the loader simultaneously. If a loader manufactured after January 1st 2016 is

equipped with the optional Attachment control switch pack, the electric socket is already integrated in the

loader connector. All loaders with electric socket next to the multi connector can be upgraded to the new

system.

From January 1st 2016 the Attachment

control switch pack option is available on all

articulated Avant loaders with the following

product numbers, in these the electric socket

is integrated to the multi connector:

A36880 Attachment control switch

pack for 200 series 2

A36878 Attachment control switch

pack for 400-700 series

A36879 Attachment control switch

pack forR series

Attachment control

pack - Extra switches

on boom control lever

Electric connection integrated in

the multi connector

How to operate an attachment with electric features, if the attachment control switch pack is not

upgraded

In case the adapter is not fitted on the loader, the attachment can be operated with the loader control

switch pack by unplugging the electric wire from the attachment multi connector and then fitting it to the

socket next to the loader socket, or with the electric wire harness with a separate switch. However, it is

recommended to install the adapter A36869 to the loader connector to have full advantage of the quick

coupling system.

If the loader is fitted with the socket on the multi connector, but the attachment has separate electric plug,

the adapter A36679 must be fitted on the attachment multi connector. All attachments with electric

features can be upgraded to have all connectors in the multi connector system

If the loader is not equipped with the attachment control switch pack or the multi connector

All attachments with electric features are equipped with a separate cable, as before, making it possible to

operate it without the attachment control switch pack. This wire is equipped with a separate switch to control

the electric functions of the attachment. Some attachments may require that the attachment control switch

pack is fitted to make it possible to control all electric functions.

If the multi connector, or the attachment control switch pack have not been fitted to your loader, they can be

also retrofitted to most loaders. Contact your Avant dealer or service point for more information.

4 (8)

2. Safety

The following warning symbols are used throughout this manual to indicate factors that must be taken into

account to reduce the risk of personal injury or damage to property:

WARNING:

This safety symbol refers to important safety information in this manual.

It warns of an immediate hazard that could cause serious personal

injury.

Read the warning text accompanying the symbol carefully and ensure

that other operators are also familiar with the warnings, since personal

safety is at stake.

This signal word indicates information about the correct operation and maintenance

of the equipment.

Failure to observe the instructions accompanying the symbol can lead to equipment

breakdown or other property damage.

Read all safety instructions carefully before beginning installation work

Lower the loader boom completely down and depressurize hydraulics when working

near the loader connector.

Disconnect battery before working on the loader.

Make sure the connectors are aligned correctly. Incorrect alignment may cause

sparking and damage the electric systems of the attachment and the loader.

Test the operation of the electric functions of the attachment at a safe location to

make sure the connections are made correctly.

5 (8)

3. Multi connector system with electric connection

3.1 Fitting the electric connector to attachment multi connector

If the loader is equipped with the electric socket integrated into the multi connector, the attachment connector

can be fitted with adapter A36679.

The adapter A36679 is equipped with all attachments with electric functions, and which are delivered after

January 1st 2016.

The adapter A36679 can be purchased separately and fitted to update all attachments already equipped with

the multi connector.

Fitting the electric socket to attachment coupler

1. Remove the plug from the attachment

coupler.

If the plug is solid type, remove by

forcing the plug out, by using a hammer

and a bolt, for example

If the plug is threaded on the connector,

and has a hexagonal on it, remove with

an Allen key

2. Bolt the attachment socket to the multi

connector with the three provided screws,

making sure that the attachment socket is

correctly oriented.

The marker on the electric socket must

point to corresponding marker on the

multi connector, so that the pins are

aligned correctly.

The marker on the loader socket will

then be aligned with the marker on the

attachment connector plug.

3. Fasten the electric plug of the attachment

to the installed adapter on the multi

connector.

6 (8)

3.2 Fitting the electric connector to loader multi connector

If the loader is equipped with the previous type attachment control switch pack A34700 (socket is not on the

multi connector), and new attachments with socket on the multi connector need to be mounted, the adapter

A36869 can be easily fitted to the loader multi connector. The following instrucions show how to integrate the

separate electric socket next to the multi connector into the multi connector system.

It is possible to continue using an attachment without fitting the socket on the loader coupler. In this case, the

electric socket must be connected directly to the plug next to the multi connector of the loader.

Disconnect battery before installation work

The loader battery must be disconnected before beginning installation of the attachment

socket on the loader. Before the socket is fitted correctly, contact with metal structures of

the loader wil cause shorting the electric circuit.

To fit the electric socket to loader multi connector:

1. Disconnect the loader battery

2. Turn the retainer ring of the old socket to open and

remove it

3. Unplug the electric cable from the old socket

4. Slide the adapter A36869 to the empty hole on the

loader connector:

a) Put the protective cap first in

b) Slide the spring in

c) Push the socket in the hole. If it doesn’t slide

easily, make sure to push and keep the spring in

the hole first

d) Make sure the socket is properly oriented. The

small indicator lump on the connector must point to

upper left direction when seen from the driver’s seat

e) Secure the connector with three provided screws,

making sure that the attachment socket is correctly

oriented

5. Fit the electric connector of the original socket to the

new installed adapter. Make sure the electric cable is

not pinned or get stretched in useTo fit the electric

socket to loader multi connector:

Incorrect alignment of the plug can damage the electric systems of the attachment or the

loader. Make sure the plug aligns with the socket on the loader correctly.

7 (8)

4. Technical information

Connection of wires, seen from the wire pin side of the connector.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Avantco Adapter Handbücher

Avantco

Avantco A37235 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung