Avaya X330G2 Bedienungsanleitung
Catalog No. 130114 Rev. AJune 2001 1
Avaya
Avaya X330G2 Expansion Module Installation Guide
The Avaya X330G2 Expansion Sub-Module is the GBIC (1.25 Gbit/s Gigabit
Ethernet) Expansion sub-module for the Avaya P330 family of stackable switches.
Note: In order to use this module the Avaya P330 switch must must have
Embedded S/W Version 2.2 or higher. You can download this from:
http://www.avayanetwork.com
The X330G2 can be used either as a Gigabit Ethernet link or as a high Bandwidth
backplane for connecting switches. The introduction of the GBIC interface to the
Avaya P330 family presents an added value over the existing Gigabit Ethernet
expansion modules. You can insert any of the Avaya-authorized GBIC transceivers
into the X330G2 Expansion sub-module socket. This provides you with a highly
modular and customisable Gigabit Ethernet interface. The GBIC transceivers are
hot-swappable.
Safety Information
The multimode and single-mode GBIC transceivers are Class 1 Laser products.
They comply with EN 60825-1 and Food and Drug Administration (FDA) 21 CFR
1040.10 and 1040.11.
The GBIC transceivers must be operated under recommended operating conditions.
Laser Classification
Note: Class 1 lasers are inherently safe under reasonably foreseeable conditions of
operation.
Caution: The use of optical instruments with this product will increase eye hazard.
CLASS 1
LASER PRODUCT
2 Avaya X330G2 Expansion Module Installation Guide
Usage Restriction
When a GBIC transceiver is inserted in the X330G2 Expansion sub-module but is not
in use, then the Tx and Rx ports should be protected with an optical connector or a
dust plug.
Avaya Approved GBIC Transceivers
Caution: All Avaya appoved GBICs are 5V. Do not insert a 3.3V GBIC.
Avaya supplies the following two GBIC transceivers for the Avaya P330 X330G2
Expansion Sub-modules. You can order these directly from your local Avaya
representative using the PEC or COM Codes:
Note: The ELX transceiver is for the Avaya P330 only.
In addition, Avaya has tested and approved a number of GBIC transceivers from
other manufacturers for use with the Avaya X330G2 Expansion sub-module. An up-
to-date list can be found in Avaya Networks’ World-Wide Web site at the following
address: http://www.avayanetwork.com/ Click on the “Supported Devices” icon.
Installation
Installing the Expansion Module in the Avaya P330
1 Remove the blanking plate or other module (if installed) from the Avaya P330
Expansion slot.
2 Insert the Expansion Sub-module gently in the slot, ensuring that the board is
aligned with the rails.
Type Description PEC Code COM Code
GBIC SX
Transceiver
Multimode Fiber
1000Base-SX (550 m)
4705-122 108659228
GBIC LX
Transceiver
Single-mode Fiber
1000Base-LX (10 km)
4705-121 108659210
GBIC ELX
Transceiver
Single-mode Fiber Long
Range GBIC (80 km)
(same as P880)
4589-810 700013147
Avaya X330G2 Expansion Module Installation Guide 3
Caution: The expansion modules contain components sensitive to electrostatic
discharge. In order to prevent ESD damage, the board is shipped in an antistatic bag.
Don’t touch the board unless instructed to do so. Always use a grounding strap.
3 Press the module in firmly until the connector at the back of the module is
completely inserted into the internal Avaya P330 connector.
4 Gently tighten the two screws on the front panel of the expansion module by
turning the knobs.
5 We recommended that you reset the Avaya P330.
Removing an Existing Expansion Module
1 Loosen the screws by turning the knobs.
2 Grasp the two knobs, one near each side of the front panel, and pull gently but
firmly towards yourself.
3 Insert another expansion module or the blanking plate.
4 We recommended that you reset the Avaya P330.
Note: You must not use the Avaya P330 switch when the expansion slot is
uncovered. In case the slot is empty cover it with the supplied blanking plate.
Installing and Removing GBIC Transceivers
Caution: Use only 5V Avaya-authorized 1.25 Gbit/s GBIC transceivers.
Two types of GBIC transceivers are supported, one fastened using snap-in clips and
the other using a locking spring.
GBIC Transceiver with Clips
• Insert the transceiver (take care to insert it the right way up, arrows on top) until
it clicks in place.
• To remove the transceiver, press the clips on either side of the transceiver at the
same time and pull the transceiver out.
GBIC Transceiver with a Locking Spring
• Ensure that there are no cables connected to the GBIC.
• Lift up the GBIC transceiver locking spring and insert the transceiver (take care
to insert it the right way up, it will not fit in upside down) until it is completely
inside the socket. To secure the GBIC transceiver in place, push down the
locking spring.
• To remove the GBIC, remove the cables, lift up the locking spring and pull out
the transceiver.
4 Avaya X330G2 Expansion Module Installation Guide
Specifications
X330G2- LX GBIC Transceiver
A 9 µm or 10 µmsingle-mode fiber (SMF) cable may be connected to a
1000Base-LX GBIC port. The maximum length is 10 km (32,808 ft).
A 50 µmor 62.5 µmmultimode (MMF) fiber cable may be connected to a
1000Base-LX GBIC port. The maximum length is 550 m (1,804 ft.) for 50 µmand
62.5 µmcable.
The LX transceiver has a Wavelength of 1300 nm, Transmission Rate of 1.25 Gbps
and Input Power of 5V.
X330G2- SX GBIC Transceiver
A 50 µmor 62.5 µmmultimode (MMF) fiber cable may be connected to a 1000Base-
SX GBIC port. The maximum length is 500 m (1,640 ft.) for 50 µmcable and 220 m
(722 ft.) for 62.5 µmcable.
The SX transceiver has a Wavelength of 850 nm, Transmission Rate of 1.25 Gbps and
Input Power of 5V.
ELX Transceiver
A 9 µm or 10 µm single-mode fiber (SMF) cable may be connected to a
1000Base-ELX GBIC port. The maximum length is 80 km (49.7 miles).
The ELX transceiver has a Wavelength of 1550 nm, Transmission Rate of 1.25 Gbps
and Input Power of 5V.
Agency Approval
The transceivers comply with:
• EMC Emission: US – FCC Part 15, Subpart B, Class A;
Europe – EN55022 class A
• Immunity: EN50082-1
• Safety: UL for US UL 1950 Std., C-UL (UL for Canada) C22.2 No.950 Std., Food
and Drug Administration (FDA) 21 CFR 1040.10 and 1040.11, and CE for
Europe EN60950 Std. Complies with EN 60825-1.
MTBF
The Mean Time Between Failures (MTBF) for the X330G2 Expansion Sub-module is
594,639 hours.
www.avaya.com
All other trademarks, registered trademarks, service names, product and/or brand names are the sole
property of their respective owners.
Copyright ©2001 Avaya Inc.All rightsreserved.
Inhaltsverzeichnis
Andere Avaya Steuereinheit Handbücher
Avaya
Avaya 100A Leitfaden
Avaya
Avaya UC Bedienungsanleitung
Avaya
Avaya IP OFFICE EU24 Handbuch
Avaya
Avaya 3 Bedienungsanleitung
Avaya
Avaya J100 Series Bedienungsanleitung
Avaya
Avaya EU24BL Handbuch
Avaya
Avaya ArgentDCP Kurzanleitung
Avaya
Avaya Visio-IP500 Bedienungsanleitung
Avaya
Avaya IP Office Phone Manager Bedienungsanleitung
Avaya
Avaya 1200 Series Bedienungsanleitung
Avaya
Avaya one-X Deskphone SBM24 Referenzhandbuch
Avaya
Avaya IP OFFICE EU24 Bedienungsanleitung
Avaya
Avaya Partner 308EC Bedienungsanleitung
Avaya
Avaya AA1419043-E6 Bedienungsanleitung
Avaya
Avaya JBM24 Datenblatt
Avaya
Avaya Cajun P580 Bedienungsanleitung
Avaya
Avaya ArgentPhone Kurzanleitung
Avaya
Avaya M460ML-SPV Bedienungsanleitung
Avaya
Avaya J100 Series Handbuch
Avaya
Avaya UC110 Benutzerhandbuch
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
