Avaya QuesCom 400 Beilage

Avaya Solution & Interoperability Test Lab

Application Notes for Configuring QuesCom 400 IP/GSM

Gateway with Avaya Communication Manager using H.323

Trunks – Issue 1.0

Abstract

These Application Notes describe the configuration steps required for the QuesCom IP/GSM

400 to successfully interoperate with Avaya Communication Manager using H.323 trunks.

The QuesCom 400 IP/GSM is an IP-GSM-gateway, supporting outgoing and incoming GSM

calls. All GSM calls made from Avaya Communications Manager will be routed to the

QuesCom 400 IP/GSM gateway to the GSM network. The QuesCom 400 IP/GSM can also

receive calls from the GSM network and route the calls to Avaya Communications Manager.

The QuesCom 400 IP/GSM can provide a backup route for the PSTN and also be backed up

by the PSTN.

Information in these Application Notes has been obtained through compliance testing and

additional technical discussions. Testing was conducted via the DeveloperConnection

Program at the Avaya Solution and Interoperability Test Lab.

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

1. Introduction

These Application Notes describe a compliance-tested configuration consisting of a QuesCom

400 IP/GSM gateway networked with Avaya Communication Manager 3.1 using H.323 trunks.

The QuesCom 400 IP/GSM is an IP-GSM-gateway, supporting outgoing and incoming GSM

calls. All calls made from Avaya Communications Manager destined for the GSM network will

be routed to the QuesCom 400 IP/GSM gateway. The QuesCom 400 IP/GSM can also receive

calls from the GSM network and route the calls to Avaya Communications Manager. The

QuesCom 400 IP/GSM can provide a backup route for the PSTN and also be backed up by the

PSTN. This can be configured in Avaya Communication Manager using Automatic Route

Selection (ARS). These Application Notes focus on a configuration where an H.323 IP trunk

connects Avaya Communication Manager and the QuesCom 400 IP/GSM.

In Figure 1, Avaya Communication Manager runs on the Avaya S8500 Media Server. The

solution described herein is also extensible to other Avaya Media Servers and Media Gateways.

The Avaya G650 Media Gateway is connected to the PSTN via an E1 ISDN-PRI line and to the

QuesCom 400 IP/GSM via an H.323 IP trunk. The QuesCom in turn connects to the GSM

network via Subscriber Identity Module (SIM) cards that reside on GSM boards inserted in the

QuesCom 400 IP/GSM.

Figure 1: Avaya Communication Manager with QuesCom IP/GSM 400

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

2. Equipment and Software Validated

Equipment Software

Avaya S8500 Media Server – Avaya Communication

Manager 3.1.2 (03.1-01.0.632.1)

Avaya C364T-PWR Converged Stackable Switch 4.3.12

Avaya 4620SW IP Telephones 2.2.3

Avaya G650 Media Gateway -

TN2312BP IP Server Interface 30

TN799DP C-LAN Interface 17

TN2302AP IP Media Processor 110

TN464CP DS1 Interface 18

QuesCom 400 IP/GSM

Additional patch needed during compliance testing IAD04.20 B029 P006

ProxyH323.dll version

4.20.017

3. Configure Avaya Communication Manager

Initial configuration of Avaya Communication Manager is beyond the scope of these Application

Notes. See Section 9 for Avaya documentation references. This section illustrates the

configuration of the H.323 trunk groups and signalling groups, dial plan, ARS analysis, and route

patterns used in the compliance-tested configuration. The steps are performed from the System

Access Terminal (SAT) interface.

3.1. Avaya Communication System parameters Special Applications

Step Description

1. Display the system-parameters special-applications command and ensure that (SA8507) -

H245 Support With Other Vendors? is set to “y”. If not, contact your Avaya authorized sales

representative to enable this feature. Note: This feature only needs to be enabled if FastStart is

enabled on the QuesCom 400 IP/GSM.

display system-parameters special-applications Page 4 of 6

SPECIAL APPLICATIONS

(SA8481) - Replace Calling Party Number with ASAI ANI? n

(SA8500) - Expanded UUI Display Information? n

(SA8506) - Altura Interoperability (FIPN)? n

(SA8507) - H245 Support With Other Vendors? y

(SA8508) - Multiple Emergency Access Codes? n

(SA8510) - NTT Mapping of ISDN Called-Party Subaddress IE? n

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

3.2. PSTN E1 ISDN-PRI

This section displays the PSTN E1 ISDN-PRI configuration on Avaya Communication Manager

in the sample configuration of Figure 1. See Section 9 for Avaya documentation references.

Step Description

1. Enter the display ds1 <board location> to display the PSTN DS1 Circuit Pack configuration.

display ds1 01A12

DS1 CIRCUIT PACK

Location: 01A12 Name: PRI to BT

Bit Rate: 2.048 Line Coding: hdb3

Signaling Mode: isdn-pri

Connect: network

TN-C7 Long Timers? n Country Protocol: etsi

Interworking Message: PROGress Protocol Version: b

Interface Companding: alaw CRC? y

Idle Code: 01010100

DCP/Analog Bearer Capability: 3.1kHz

T303 Timer(sec): 4

Slip Detection? n Near-end CSU Type: other

2. Enter the display trunk-group <number> to display the PSTN trunk-group configuration.

display trunk-group 19 Page 1 of 22

TRUNK GROUP

Group Number: 19 Group Type: isdn CDR Reports: y

Group Name: PRI to BT COR: 1 TN: 1 TAC: 719

Direction: two-way Outgoing Display? n Carrier Medium: PRI/BRI

Dial Access? y Busy Threshold: 255 Night Service:

Queue Length: 0

Service Type: public-ntwrk Auth Code? n TestCall ITC: rest

Far End Test Line No:

TestCall BCC: 4

display trunk-group 19 Page 2 of 22

Group Type: isdn

TRUNK PARAMETERS

Codeset to Send Display: 6 Codeset to Send National IEs: 6

Max Message Size to Send: 260 Charge Advice: none

Supplementary Service Protocol: a Digit Handling (in/out): enbloc/overlap

Trunk Hunt: cyclical QSIG Value-Added? n

Digital Loss Group: 13

Incoming Calling Number - Delete: Insert: Format:

Bit Rate: 1200 Synchronization: async Duplex: full

Disconnect Supervision - In? y Out? n

Answer Supervision Timeout: 0

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

Step Description

display trunk-group 19 Page 3 of 22

TRUNK FEATURES

ACA Assignment? n Measured: both Wideband Support? n

Maintenance Tests? y

Data Restriction? n NCA-TSC Trunk Member:

Send Name: n Send Calling Number: y

Used for DCS? n Send EMU Visitor CPN? n

Suppress # Outpulsing? y Format: public

Outgoing Channel ID Encoding: preferred UUI IE Treatment: shared

Maximum Size of UUI IE Contents: 128

Replace Restricted Numbers? n

Replace Unavailable Numbers? n

Send Connected Number: y

Hold/Unhold Notifications? y

Send UUI IE? y Modify Tandem Calling Number? n

Send UCID? n BSR Reply-best DISC Cause Value: 31

Send Codeset 6/7 LAI IE? y Ds1 Echo Cancellation? n

Apply Local Ringback? n US NI Delayed Calling Name Update? n

Network (Japan) Needs Connect Before Disconnect? n

display trunk-group 19 Page 6 of 22

TRUNK GROUP

Administered Members (min/max): 1/5

GROUP MEMBER ASSIGNMENTS Total Administered Members: 5

Port Code Sfx Name Night Sig Grp

1: 01A1201 TN2464 C 19

2: 01A1202 TN2464 C 19

3: 01A1203 TN2464 C 19

4: 01A1204 TN2464 C 19

5: 01A1205 TN2464 C 19

3. Enter the display signaling-group <number> to display the PSTN signaling-group

configuration.

display signaling-group 19 Page 1 of 5

SIGNALING GROUP

Group Number: 19 Group Type: isdn-pri

Associated Signaling? y Max number of NCA TSC: 5

Primary D-Channel: 01A1216 Max number of CA TSC: 5

Trunk Group for NCA TSC: 19

Trunk Group for Channel Selection: 19 X-Mobility/Wireless Type: NONE

Supplementary Service Protocol: a

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

3.3. H.323 Trunks and Signaling Groups

The steps in this section create an H.323 IP trunk group to the QuesCom 400 IP/GSM.

Step Description

1. Enter the change node-names ip command. Specify the node name and IP address for the

QuesCom 400. Observe the node name of the C-LAN card shown in bold. These node names

will be used in the configuration of the H.323 signalling group in Step 4.

change node-names ip Page 1 of 1

IP NODE NAMES

Name IP Address Name IP Address

AEServer 10 .1 .10 .20 . . .

Abacus 10 .1 .10 .31 . . .

IPO412a_DC1 10 .1 .20 .10 . . .

Quescom 10 .1 .10 .55 . . .

S8300a_DC1 10 .1 .30 .10 . . .

S8500_Val1 10 .1 .10 .14 . . .

SEServer 10 .1 .10 .22 . . .

clan1a_DC1 10 .1 .10 .12 . . .

default 0 .0 .0 .0 . . .

medpro1a_DC1 10 .1 .10 .13 . . .

procr 10 .1 .10 .10 . . .

2. Enter the add trunk-group n command, where “n” is an available trunk group number. On

Page 1 of the trunk-group form, configure the following:

• Group Type – set to “isdn”.

• Group Name – enter a meaningful name/description.

• TAC – enter a Trunk Access Code that is valid under the provisioned dial plan.

• Carrier Medium – set to “H.323”.

• Service Type – set to “tie”.

add trunk-group 27 Page 1 of 21

TRUNK GROUP

Group Number: 27 Group Type: isdn CDR Reports: y

Group Name: H.323 Quescom COR: 1 TN: 1 TAC: 727

Direction: two-way Outgoing Display? n Carrier Medium: H.323

Dial Access? y Busy Threshold: 255 Night Service:

Queue Length: 0

Service Type: tie Auth Code? n

Member Assignment Method: manual

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

Step Description

3. On the TRUNK FEATURES screen (Page 3 of the trunk-group form), set the Send Name, Send

Calling Number and Send Connected Number to “y” and verify the Format is set to “public”

as shown below.

add trunk-group 27 Page 3 of 21

TRUNK FEATURES

ACA Assignment? n Measured: none

Internal Alert? n Maintenance Tests? y

Data Restriction? n NCA-TSC Trunk Member: 1

Send Name: y Send Calling Number: y

Used for DCS? n Send EMU Visitor CPN? n

Suppress # Outpulsing? n Format: public

UUI IE Treatment: service-provider

Replace Restricted Numbers? n

Replace Unavailable Numbers? n

Send Connected Number: y

Hold/Unhold Notifications? n

4. Enter the add signaling-group n command, where “n” is an unused signalling group number.

On Page 1 of the form, configure the following:

• Group Type – set to “h.323”.

• Trunk Group for Channel Selection – enter the number of the trunk group configured

in Step 2.

• Near-end Node Name – enter the node name of a local C-LAN board from Step 1.

• Near-end Listen Port – specify the local listen port, typically 1720.

• Far-end Node Name – enter the node name of the QuesCom configured in Step 1.

• Far-end Listen Port – specify the listen port, typically 1720.

• Direct IP-IP Audio Connections – set to “n”.

add signaling-group 27 Page 1 of 5

SIGNALING GROUP

Group Number: 27 Group Type: h.323

Remote Office? n Max number of NCA TSC: 5

SBS? n Max number of CA TSC: 5

IP Video? n Trunk Group for NCA TSC: 27

Trunk Group for Channel Selection: 27

Supplementary Service Protocol: a

T303 Timer(sec): 10

Near-end Node Name: clan1a_DC1 Far-end Node Name: Quescom

Near-end Listen Port: 1720 Far-end Listen Port: 1720

Far-end Network Region: 1

LRQ Required? n Calls Share IP Signaling Connection? n

RRQ Required? n H245 Control Addr On FACility? n

Bypass If IP Threshold Exceeded? n

H.235 Annex H Required? n

DTMF over IP: out-of-band Direct IP-IP Audio Connections? n

IP Audio Hairpinning? n

Interworking Message: PROGress

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

Step Description

5. Enter the change trunk-group n command, where “n” is the trunk group number configured in

Step 2. On Page 3 of the trunk-group form, configure the following:

• “IP” for Port. The number of ports configured should be coordinated with the number of

SIM cards available in the QuesCom 400 gateway.

• The number of the signaling group configured in Step 3 for Sig Grp.

change trunk-group 27 Page 5 of 21

TRUNK GROUP

Administered Members (min/max): 1/10

GROUP MEMBER ASSIGNMENTS Total Administered Members: 10

Port Name Night Sig Grp

1: IP 27

2: IP 27

3: IP 27

4: IP 27

5: IP 27

3.4. ARS Tables and Route Patterns

In the sample configuration described in these Application Notes, when placing outbound calls to

the public network, stations on Avaya Communication Manager must first dial the ARS Feature

Access Code (FAC) before dialing an external number. The single digit “9” was used as the

ARS FAC in the compliance-tested configuration (configuration step not shown).

Step Description

1. Enter the change ars analysis 0command. Configure Dialed String entries according to

customer requirements. In the example below, the entries match dialed numbers as follows:

• The “078” Dialed String matches 11-digit dialed numbers that begin with 078, and

routes calls to Route Pattern 78. For example, a dialed number of 07891 900 128 would

be matched by this entry.

change ars analysis 0 Page 1 of 2

ARS DIGIT ANALYSIS TABLE

Location: all Percent Full: 0

Dialed Total Route Call Node ANI

String Min Max Pattern Type Num Reqd

01 11 11 9 pubu n

078 11 11 78 pubu n

079 11 11 79 pubu n

123 3 3 9 pubu n

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

Step Description

2. Enter the change route-pattern n command, where “n” is the route pattern that processes dialed

numbers configured in Step 1. Add two routing preference entries as follows:

1) First Routing Preference – H.323 IP trunk to QuesCom 400

• Grp No – enter the trunk group number routed to the QuesCom 400 gateway (see Section

3.3, Step 2)

• FRL - assign a Facility Restriction Level to this routing preference.

• LAR - set Look Ahead Routing to “next” to rehunt within the next routing preference if

calls are rejected. LAR allows Avaya Communication Manager to re-attempt the call on

another channel if the call is rejected with certain cause values.

2) Second Routing Preference – PSTN E1 ISDN-PRI

• Grp No – enter the trunk group that contains trunk members from the PSTN E1 ISDN-PRI

(see Section 3.2 Step 2).

• FRL - assign a Facility Restriction Level to this routing preference.

change route-pattern 78 Page 1 of 3

Pattern Number: 78 Pattern Name: Quescom H.323

SCCAN? n Secure SIP? n

Grp FRL NPA Pfx Hop Toll No. Inserted DCS/ IXC

No Mrk Lmt List Del Digits QSIG

Dgts Intw

1: 27 0 n user

2: 19 0 n user

3: n user

4: n user

5: n user

6: n user

BCC VALUE TSC CA-TSC ITC BCIE Service/Feature PARM No. Numbering LAR

0 1 2 3 4 W Request Dgts Format

Subaddress

1: y y y y y n n rest next

2: y y y y y n n rest none

3: y y y y y n n rest none

4: y y y y y n n rest none

5: y y y y y n n rest none

6: y y y y y n n rest none

HJP; Reviewed:

SPOC 9/14/2006 Solution & Interoperability Test Lab Application Notes

QuescomACM_H323

3.5. Avaya Extension to Cellular(EC500) Configuration

Avaya Extension to Cellular allows a cell phone to be treated as if it were an extension defined in

Avaya Communication Manager. This is accomplished by mapping the user’s main office phone

to the cellular telephone number. All other types of calls, such as direct calls to and from the

published cell phone number, are unaffected by Extension to Cellular.

Step Description

1. Verify that the Avaya Communication Manager license has permissions for EC500 extensions.

Enter the command display system-parameters customer-options. On the OPTIONAL

FEATURES screen, verify that the Maximum Off-PBX Telephones - EC500 is sufficient.

display system-parameters customer-options Page 1 of 11

OPTIONAL FEATURES

G3 Version: V13

Location: 2 RFA System ID (SID): 1

Platform: 12 RFA Module ID (MID): 1

USED

Platform Maximum Ports: 3200 259

Maximum Stations: 2400 209

Maximum XMOBILE Stations: 2400 0

Maximum Off-PBX Telephones - EC500: 2400 1

Maximum Off-PBX Telephones - OPS: 2400 32

Maximum Off-PBX Telephones - SCCAN: 2400 0

2. Enter the display system-parameters customer-options command. On the OPTIONAL

FEATURES screen, ensure that Enhanced EC500? is set to “y” as shown below.

display system-parameters customer-options Page 4 of 11

OPTIONAL FEATURES

Emergency Access to Attendant? y IP Stations? y

Enable 'dadmin' Login? y Internet Protocol (IP) PNC? n

Enhanced Conferencing? y ISDN Feature Plus? n

Enhanced EC500? y ISDN Network Call Redirection? n

Enterprise Survivable Server? n ISDN-BRI Trunks? n

Enterprise Wide Licensing? n ISDN-PRI? y

ESS Administration? n Local Survivable Processor? n

Extended Cvg/Fwd Admin? y Malicious Call Trace? n

External Device Alarm Admin? n Media Encryption Over IP? n

Five Port Networks Max Per MCC? n Mode Code for Centralized Voice Mail? n

Flexible Billing? n

Forced Entry of Account Codes? n Multifrequency Signaling? y

Global Call Classification? y Multimedia Appl. Server Interface (MASI)? n

Hospitality (Basic)? y Multimedia Call Handling (Basic)? n

Hospitality (G3V3 Enhancements)? n Multimedia Call Handling (Enhanced)? n

IP Trunks? y

Andere Handbücher für QuesCom 400

Inhaltsverzeichnis

Andere Avaya Tor Handbücher

Avaya

Avaya MULTIVOIP MVP-130 Abmessungen

Avaya

Avaya G450 Manager Bedienungsanleitung

Avaya

Avaya Media Gateway G250 Bedienungsanleitung

Avaya

Avaya G450 Manager Bedienungsanleitung

Avaya

Avaya AudioCodes MP-118 Bedienungsanleitung

Avaya

Avaya Media Gateway G350 Bedienungsanleitung

Avaya

Avaya G860 Handbuch

Avaya

Avaya G700 Bedienungsanleitung

Avaya

Avaya G450 Manager Bedienungsanleitung

Avaya

Avaya Media Gateway G250 Installationsanleitung

Avaya

Avaya G700 Kurzanleitung

Avaya

Avaya SG5 Handbuch

Avaya

Avaya Remote Gateway 911 Series Bedienungsanleitung

Avaya

Avaya S8500 Series Bedienungsanleitung

Avaya

Avaya G450 Manager Bedienungsanleitung

Avaya

Avaya SG5 Bedienungsanleitung

Avaya

Avaya G700 Bedienungs- und Sicherheitshinweise

Avaya

Avaya Media Gateway G250 Bedienungsanleitung

Avaya

Avaya VSU 10000 Service-Handbuch

Avaya

Avaya CMC1 Bedienungsanleitung

Avaya

Avaya G700 Installationsanleitung

Avaya

Avaya Media Gateway G250 Installations- und Betriebshandbuch

Avaya

Avaya MCC1 Bedienungsanleitung

Avaya

Avaya Advanced Gateway 2330 Betriebsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung