Avdel G3LB Tool Bedienungsanleitung

G3LB Tool –Instruction Manual Supplement.

This must accompany the Manual (07900-00930) for the STD

Genesis® nG3 tool

G3LB Tool

Hydro-Pneumatic Power Tool

Original Instructions

Intent of Use

The Genesis® nG tool must “Only” be used for placing 3/16” & 1/4” NeoBolt® as outlined in “Tool setting guide – Small diameter NeoBolt®:

(07900-01071 GB)

Tool Specification

Air Pressure

Minimum - Maximum

5-7 bar

Free Air Volume Required

@ 5.5 bar

4.3 litres

Stroke

Minimum - Maximum

10-29 mm

Pull Force

@ 5.5 bar

12.9 kN

Cycle Time

Approximately

0.8 seconds

Noise Level

Less than

75 dB(A)

Weight

Without nose equipment

2.3 kg

Vibration

Less than

2.5 m/s2

Safety Instructions

For the full safety instructions refer to the associated Genesis® nG tool manual (07900-00930 GB)

Certificate of Conformity

Refer to the associated Genesis® nG Instruction Manual (07900-00930 GB)

General Assembly

Base Tool –71256-02000

Parts List

G3LB NEOBOLT PLACING TOOL VARIANT PARTS LIST

ITEM

PART NUMBER

DESCRIPTION

QTY

ITEM

PART NUMBER

DESCRIPTION

QTY

71256-02001

BODY MACHINED

71256-02006

LOCK NUT

71256-02002

PISTON STOP

71256-02005

ADJUSTING NUT

71256-02003

SPRING HOUSING

07002-00098

NYLOC NUT

71256-02004

HYDRAULIC PISTON

71256-02007

ADJUSTING STOP

07002-00202

WASHER

71256-02002

PISTON STOP

07007-02136

SPRING

07003-00472

O-RING

*NEW PARTS IN nG3 LIST

Stroke Information

The diagrams below show the minimum and maximum stroke conditions when rotating the adjusting nut 8. When the adjusting nut is unscrewed beyond

the maximum allowable stroke, air will start to leak from the rear of the adjusting nut. Do not use the tool if the air leaks from the tool. When air leaks

from the tool, isolate the air from the tool and then screw the adjusting nut back onto the spring housing 3. The adjusting nut will not have any air

pressure behind it should the end user carry on unscrewing the nut from the spring housing. When setting the stroke of the hydraulic piston 4, it is highly

recommended that the locking nut 7 is tightened into the adjusting nut 8.

Maintenance/Dismantling Instructions

THE AIR LINE MUST BE DISCCONNECTED BEFORE ANY DISMANTLING IS ATTEMPTED

1. Unscrew the Adjusting Nut 8from the Spring Housing 3by hand.

2. Unscrew the Spring Housing fully 3using a 25mmA/F spanner. Remove the Spring 6, Washer 5and Hydraulic Piston 4from the rear of the

tool.

3. To remove the Piston stop 2the Base Cover 31 must first be removed to gain access

4. Clamp the body of the inverted tool ACROSS THE AIR INLET BOSSES in a vice fitted with soft jaws.

5. Pull off Rubber Boot 48.

6. Using the peg spanner* unscrew Base Cover 31.

7. Unscrew Nyloc Nuts 67 (2 off) and remove Base Plate Assembly 65.

8. Remove Cylinder Liner 37 together with Sealing Washers 29 (2 off) and ‘O’ Rings 66 (2 off).

1. Remove Pneumatic Piston Assembly 57 together with ‘O’ Ring 75, Lip Seal 90 (3 off), Guide Ring 51 and Piston Stop 2.

Re-assemble in the reverse order.

For Safety and Full Servicing and Maintenance instructions, refer to the nG3 Genesis® tool Manual (07900-00930 GB).

Item numbers in bold refer to the parts list on page 2 in this flyer and page 24 in the nG3 tool manual

Manual Number

Issue

C/N

07900-01067

16/303

Avdel UK Limited

Stanley House, Works Road

Letchworth Garden City, Hertfordshire SG6 1JY

Tel. +44 1582 900-000 –Fax -001

[email protected]

Avdel®, Genesis®and NeoBolt®, are registered trademarks of Avdel UK Limited.

AV™ is a trademark of Avdel UK Limited.

The names and logos of other companies mentioned herein may be trademarks of their respective

owners.

This document is for informational purposes only. Avdel UK Limited makes no warranties, expressed

or implied, in this document.

Data shown is subject to change without prior notice as a result of continuous product development

and improvement policy.

Your local STANLEY Engineered Fastening representative is at your disposal should you need to

confirm latest information.

Inhaltsverzeichnis

Andere Avdel Elektrowerkzeuge Handbücher

Avdel

Avdel 7551 Bedienungsanleitung

Avdel

Avdel 74101 Bedienungsanleitung

Avdel

Avdel 73200 Tool Bedienungsanleitung

Avdel

Avdel 753 MkII Bedienungsanleitung

Avdel

Avdel Genesis G2LB Bedienungsanleitung

Avdel

Avdel Genesis G2LB Bedienungsanleitung

Avdel

Avdel TX2000 Bedienungsanleitung

Avdel

Avdel Genesis G2LB Bedienungsanleitung

Avdel

Avdel 07900-09080 Bedienungsanleitung

Avdel

Avdel 07281 Bedienungsanleitung

Avdel

Avdel 7536 Bedienungsanleitung

Avdel

Avdel Genesis G3 Bedienungsanleitung

Avdel

Avdel Genesis nG3 Bedienungsanleitung

Avdel

Avdel GenesisG2-s Bedienungsanleitung

Avdel

Avdel Genesis G2LB Bedienungsanleitung

Avdel

Avdel Genesis G4 HD Heavy Duty Bedienungsanleitung

Avdel

Avdel Avbolt 07220 Bedienungsanleitung

Avdel

Avdel 74100 Bedienungsanleitung

Avdel

Avdel 7539-300X Series Bedienungsanleitung

Avdel

Avdel Genesis G2LB Bedienungsanleitung

Avdel

Avdel TX2000 Bedienungsanleitung

Avdel

Avdel 7555 Bedienungsanleitung

Avdel

Avdel 71234 Bedienungsanleitung

Avdel

Avdel 7412 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch