Avid Technology Rack-Mount Kit Bedienungsanleitung
Part 0130-05337-01 Rev. B
a
Important Information
Avid recommends that you read all the installation instructions
thoroughly before installing the Compaq W8000 system into your rack
enclosure.
This optional rack-mount kit for the Compaq W8000 system is
comprised of the Compaq rack-mount kit and a rack-shelf added to
the kit by Avid. Install the rack-mount kit before making any
connections to the system. The Compaq W8000 system typically
requires five rack units with one additional rack unit for the rack-shelf.
nThe rack-mount kit includes a new front bezel that secures the
Compaq W8000 to your rack enclosure. The new rack-mont bezel does not
include the two USB connectors, the microphone jack, and the headphone jack
that are in the desktop version of the bezel. These connections are still
available on the back of the system.
Although Compaq provides a rack-mount kit for the Compaq W8000,
Avid has modified the kit to include a rack-shelf making the kit more
universal. This document provides instructions for the Compaq
rack-mount kit and the parts added to the kit by Avid.
nThis procedure requires two people for the complete installation.
Rack-Mount Kit
Installation Instructions
for the Compaq®EVO Workstation W8000
2Installation Instructions
Symbols and Conventions Part 0130-05337-01 Rev. B
Contents
Symbols and Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installing the Rack Nuts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the Rack-Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Installing the Tower-to-Rack Conversion Kit . . . . . . . . . . . . . . . . . . . . . 6
Removing the Side Access Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Removing the Front Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Replacing the Diskette Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Removing the Front I/O Assembly Module . . . . . . . . . . . . . . . . . 10
Installing the Rack-Mount Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Rack-Mount Front Bezel. . . . . . . . . . . . . . . . . . . . . . 13
Installing the Compaq W8000 into the Rack. . . . . . . . . . . . . . . . . . . . . 14
Technical Support Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Symbols and Conventions
These installation instructions use the following special symbols and
conventions:
nA note provides important related information, reminders, recommendations,
and strong suggestions.
cA caution means that a specific action you take could cause harm to
your computer or cause you to lose data.
wA warning describes an action that could cause you physical harm.
Follow the guidelines in the manual or on the unit itself when
handling electrical equipment.
Installation Instructions 3
Part 0130-05337-01 Rev. B Installing the Rack Nuts
Installing the Rack Nuts
Rack nuts are provided in the kit for those rack enclosures that do not
have threaded holes. Rack nut clips position the rack nuts at the holes
of the rack and are used to secure the rack components in place. Install
the rack nuts where the rack-shelf and front bezel will secure to the
rack enclosure. If your rack enclosure has threaded holes, skip this
procedure.
To attach the rack nuts to the rack enclosure:
1. On the inside of the rail, hook one of the rack nut clips through the
desired hole, see Figure 1.
2. Squeeze the nut housing and hook the opposite clip of the rack nut
in the hole.
Figure 1 Clipping Rack Nuts onto the Rack Enclosure
Rack nut
(on inside of rail)
Rack nut clip coming
through hole
Rack enclosure
mounting rail
4Installation Instructions
Installing the Rack-Shelf Part 0130-05337-01 Rev. B
Installing the Rack-Shelf
You must first install the rack-shelf in your rack enclosure before you
can install the Compaq W8000. The rack-shelf requires one EIA rack
unit (1 U), or 1 3/4inches of rack space. Once the shelf is secured in the
rack, the Compaq W8000 rests on top of the shelf and is also secured.
wTo ensure the stability of the rack enclosure, install the rack
components in the rack enclosure starting from the bottom.
To attach the rack-shelf to the rack enclosure:
1. Locate the rack-shelf and position the shelf just below where you
want to have the Compaq W8000 located in the rack.
2. Select the lowest position in the rack where you can mount the
rack-shelf and Compaq W8000. Position the rack-shelf so that the
bottom of the shelf is at the baseline of a U-alignment position (see
Figure 2).
Figure 2 Positioning the Rack-Shelf
5/8 in
5/8 in
1/2 in
5/8 in
5/8 in
1/2 in
5/8 in
5/8 in
1/2 in
5/8 in
5/8 in
1/2 in
1 U
2 U
3 U
Rack-shelf
Rack mounting rail
EIA rack unit
Rack mounting rail
1 3/4 in
1 3/4 in
1 3/4 in Baseline of rack-shelf is at U-alignment
position between two 1/2-inch holes.
hole spacing
Installation Instructions 5
Part 0130-05337-01 Rev. B Installing the Rack-Shelf
nYou should have someone helping you to hold the shelf while you are
securing it.
3. Position the front of the rack-shelf flush against the outside of the
front mounting rail. Align the holes in the rack-shelf with the
holes in the front mounting rail (see Figure 3).
4. From the front of the rack enclosure, insert the screws (with teflon
washers) through the front mounting rail and tighten.
Figure 3 Left Front Slide Bracket
5. Adjust the length of the slide rails on the rack-shelf so they mount
on the rear mounting rail of the rack-enclosure (see Figure 4).
Teflon washer
Rack enclosure front
mounting rail
Screw
6Installation Instructions
Installing the Tower-to-Rack Conversion Kit Part 0130-05337-01 Rev. B
6. From the rear of the rack enclosure, insert a screw with teflon
washer through the slide rail and tighten the screw to the rear
mounting rail.
Figure 4 Left Rear Slide Bracket and Adjustment Screws
7. Secure the other side of the rack-shelf by repeating steps 3 to 6.
Installing the Tower-to-Rack Conversion Kit
Avid’s instructions for the Compaq Tower-to-Rack Conversion Kit
includes information on the components that Avid has added, and
excludes steps for Compaq components that are not used by Avid.
Avid systems must use the rack-shelf (see “Installing the Rack-Shelf”
on page 4). These instructions have been specifically tailored for Avid
systems.
Slide rail
Rack enclosure rear
mounting rail
Screw
Teflon washer
Installation Instructions 7
Part 0130-05337-01 Rev. B Installing the Tower-to-Rack Conversion Kit
Removing the Side Access Panel
cBefore removing the access panel, ensure that the Compaq W8000 is
turned off, and all cables are disconnected from the back of the
system.
To remove the side access panel:
1. Loosen the four rear panel thumbscrews (see Figure 5).
2. Slide the side access panel back, then off.
Figure 5 Removing the Side Access Panel
1 of 4 thumb screws Side access panel
8Installation Instructions
Installing the Tower-to-Rack Conversion Kit Part 0130-05337-01 Rev. B
Removing the Front Bezel
To remove the front bezel:
1. Release the two front bezel latches (see Figure 6).
2. Pull the front bezel off the front of the system from the latch side.
Figure 6 Removing the Front Bezel
Replacing the Diskette Drive
You must replace the existing diskette drive with the diskette drive in
the rack-mount kit. The diskette drive in the rack-mount kit provides a
longer eject button. The longer button needs to extend beyond the new
front bezel.
Front bezel
Latches
Installation Instructions 9
Part 0130-05337-01 Rev. B Installing the Tower-to-Rack Conversion Kit
To remove the diskette drive:
1. Remove the two screws that secure the diskette drive (see
Figure 7).
2. Slide the diskette drive out slightly to gain access to the cables.
3. Disconnect the signal and power cables from the back of the
diskette drive.
Figure 7 Installing the Rack-Mount Diskette Drive
4. Remove the diskette drive from the drive cage.
To install the rack-mount diskette drive:
1. Insert the new diskette drive that came with the rack-mount kit
into the drive cage (see Figure 7).
2. Connect the signal and power cables on the back of the diskette
drive.
Diskette drive
Screws
Drive cage
10 Installation Instructions
Installing the Tower-to-Rack Conversion Kit Part 0130-05337-01 Rev. B
3. Secure the diskette drive with the screws removed from the
original diskette drive.
cUse only 5mm-long screws. Longer screws can damage the internal
components of the diskette drive. Be sure cables are placed in their
original locations during the reassembly process. Improper cable
placement can damage the system.
Removing the Front I/O Assembly Module
To remove the front I/O assembly module:
1. Remove the four screws securing the front I/O assembly module
to the chassis (see Figure 8).
Figure 8 Removing the Front I/O Assembly Module
Front I/O assembly
module
1 of 4 screws
Power-on
ribbon cable
Inhaltsverzeichnis
Andere Avid Technology Rack & Stand Handbücher
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
