Avigilon H3-3MH-DC1 Bedienungsanleitung

Web Interface User Guide

Avigilon™ High Definition H.264 IP Camera Models:

ENC-4P-H264, H3-B1, H3-B2, H3-B3, H3-BO1-IR, H3A-

BO1-IR, H3-BO2-IR, H3A-BO2-IR, H3-D1, H3-D2, H3-DC1,

H3-DC2, H3-3MH-DC1, H3-4MH-DC1, H3-DO1, H3A-DO1,

H3-DO2, H3A-DO2, H3-3MH-DO1, H3-4MH-DO1, H3-DP1,

H3A-DP1, H3-DP2, H3A-DP2, H3-3MH-DP1, H3-4MH-DP1,

H3M-DC1, H3M-DO1, H3M-DP1, and H3PTZ

CENTER, and ACC are trademarks of Avigilon Corporation. Other product names mentioned herein may be the

trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each trademark in this

document is not a disclaimer of ownership of the related trademark. Avigilon Corporation protects its innovations

with patents issued in the United States of America and other jurisdictions worldwide:

http://www.avigilon.com/patents. Unless stated explicitly and in writing, no license is granted with respect to any

licensors.

This document has been compiled and published covering the latest product descriptions and specifications.

The contents of this document and the specifications of the products discussed herein are subject to change

without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither

Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the

information contained in this document; or (2) is responsible for your use of, or reliance on, the information.

Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages)

caused by reliance on the information presented herein.

Avigilon Corporation

http://www.avigilon.com

UG-H3-D

Revision: 13 - EN

20160524

Table of Contents

Introduction 1

System Requirements 1

Accessing the Camera Web Interface 2

Live View 3

Using the Camera Zoom and Focus Controls 3

Using Camera Presets 3

Saving a Still Image 4

Using the PTZ Camera Controls 4

Using the Encoder PTZ Controls 4

Setup 6

General 6

Network 7

Configuring 802.1x Port Based Authentication 8

Image and Display 8

Compression and Image Rate 12

Viewing the RTSP Stream URI 12

Accessing the Still Image URI 13

Motion Detection 13

Privacy Zones 14

Storage 14

Enabling Onboard Storage 15

Downloading Recorded Video From the Web Interface 15

Downloading Recorded Video From the SD Card 15

Deleting Recorded Video 16

Digital Inputs and Outputs 16

Microphone 17

Speaker 17

Users 17

Adding a User 17

Editing Users and Passwords 18

Removing a User 18

Keeping Usernames and Passwords AfterFirmware Revert 18

System 18

Upgrading the Camera Firmware 19

iii

Device Log 19

HD Multisensor Dome Camera 20

Changing Settings Per Camera Head 20

PTZ Camera 22

PTZ Tours 22

Editing PTZ Tours 23

PTZ Limits 23

Encoder 24

Selecting a Port or Channel Option 24

Enabling Video Input Termination 24

Setting Up PTZ 24

Introduction

All Avigilon™ high definition H.264 IP cameras and encoders include a web interface that allows you to view live

video and configure the device through a web browser.

Before you access the web interface, make sure you complete all the procedures described in the device

installation guide.

NOTE: Some options and features are disabled if they are not supported by the camera.

System Requirements

The web interface can be accessed from any Windows, Mac or mobile device using one of the following

browsers:

lWindows Internet Explorer browser version 7.0 or later

lMozilla Firefox browser version 3.6 or later

lChrome browser 8.0 or later

lSafari 5.0 or later

lAndroid 2.2 (Froyo) browser or later

lApple iOS 5.0 browser or later

Introduction 1

Accessing the Camera Web Interface

After the camera or encoder has been installed, you need the device’s IP address to access the web interface.

The IP address can be found in one of the following places:

lAvigilon™ Control Center Client: open the device Setup tab to see the details of the selected camera or

encoder.

lAvigilon™ Camera Installation Tool: click the Connect to Camera button to see the details of the

connected camera or encoder.

Once you have the IP address, complete the following procedure to access the web interface:

NOTE: The web browser must be configured to accept cookies or the camera web interface will not function

correctly.

1. On a computer with internet access, enter the device’s IP address into a web browser:

http://<camera IP address>/

For example: http://192.168.1.40/

2. You will automatically be prompted to enter your username and password to access the device.

The default username is admin, and the default password is admin. It is recommended that you change

the default password after your first login. For more information, see Editing Users and Passwords on

page18.

NOTE: You can only change the device password in the web interface. The password cannot be changed in the

network video management software.

2 Accessing the Camera Web Interface

Live View

After you log in, the first page you see is the Live View. The Live View contains an image panel that displays the

live video stream.

If you are accessing an HD Multisensor Dome Camera, there may be up to four image panels displayed. Click an

image panel to zoom and control the image that is displayed.

Use the menu links in the top-left corner to navigate through the web interface. Click Live View any time to

return to this page.

The following sections describe the buttons that may be displayed under the image panel if users have access

to Pan-Tilt-Zoom (PTZ) controls. PTZ controls allow users to control the zoom, focus and positioning of a camera.

To give a user PTZ controls, see Adding a User on page17.

NOTE: Some options are disabled if they are not supported by the camera.

Using the Camera Zoom and Focus Controls

lTo zoom out, move the slider towards the right.

lTo zoom in, move the slider towards the left.

lTo focus towards zero:

lClick << to take a large step.

lClick < to take a small step.

lClick 0 to focus at zero.

lTo focus towards infinity:

lClick >> to take a large step.

lClick > to take a small step.

lClick Inf to focus at infinity.

lIf the camera supports auto focusing, click Auto Focus.

Using Camera Presets

Users can save frequently used zoom and focus configurations as presets on the Live View page.

1. On the Live View page, use the Zoom and Focus controls to focus the camera on a specific point in the

video image.

2. To add this camera position as a preset, enter a name in the Add Preset field then click Add.

3. To use a preset, select a configured preset from the Presets drop down list and click Go.

4. To delete a preset, select a preset from the drop down list then click Remove.

The presets can also be configured in the Avigilon Control Center Client software through the PTZ controls.

Live View 3

Saving a Still Image

If you see the Save Still to SDCard button from the Live View page, the camera supports the ability to take

snapshots of live video from the web interface.

To use this feature, the following settings are required for the camera:

lThere is an SD card in the camera. For more information, see the camera's installation guide.

lThe camera's onboard storage settings are enabled on the Storage page. For more information, see

Storage on page14.

lThe camera's video format must be set to MJPEG in the Compression and Image Rate page. For more

information, see Compression and Image Rate on page12.

Once all the requirements have been met, you can click Save Still to SDCard any time from the Live View page

and the image is automatically saved to the SD card.

To download the snapshot, see Downloading Recorded Video From the Web Interface on page15.

Using the PTZ Camera Controls

If you are accessing a standalone Pan-Tilt-Zoom (PTZ) camera, you can control Focus and Presets in the same

way as other cameras but you also have access to other features that are specific to the PTZ camera.

1. To zoom the camera:

lAdjust the Zoom slider.

lOr, click and drag to create a green box on the image panel to define the area you want to zoom in

to see.

2. To move the camera:

lClick anywhere on the image panel to center the camera to that point.

lOr, drag your mouse from center to move the camera in that direction. The farther the arrow is from

center, the faster the camera will move.

3. To perform a guard tour, select a tour from the drop down list then click Start. To setup a tour, see PTZ

Tours on page22.

4. To stop a guard tour, click Stop. You can pause a tour at any time just by using the other PTZ controls.

Using the Encoder PTZ Controls

Any camera that is connected to an H.264 encoder can have the PTZ option enabled. Once enabled, the full

pan, tilt and zoom controls are displayed in the Live View for that camera.

To enable PTZ for cameras that are connected to an encoder, see Setting Up PTZ on page24.

4 Saving a Still Image

1. Select a camera from the Port drop down list.

NOTE: The PTZ controls are only displayed when the camera is displayed by itself.

2. To move the camera field of view, click one of the directional buttons on the far left.

3. To control the camera’s Zoom, Iris or Focus, click the + or - buttons.

4. For Presets, you can perform any of the following:

lTo add a preset, move the camera’s field of view into position then give the preset a name and

click Set.

lTo use a preset, select a name or number from the drop down list and click Go To.

5. For Patterns, you can perform any of the following:

lTo record a pattern, select a number from the drop down list then click Record. Use the directional

buttons to move the camera and create the pattern. When you are done, click Stop.

lTo run a pattern, select a number from the drop down list and click Run.

6. To activate an auxiliary command, select an Aux# from the drop down list and click Start. When you are

finished, click Stop.

Using the Encoder PTZ Controls 5

Setup

NOTE: Some options are disabled if they are not supported by the camera or if you do not have the required

user permissions.

The device’s factory default settings allow you to use the camera or encoder immediately after installation. If you

have special requirements, you can customize the settings through the web interface. In the top-left menu links

area, click Setup to display all the available setup options.

A Restore Defaults button is available on each setup page to allow you to restore the factory default settings.

Be aware that some of the settings are only available through the camera web interface and cannot be changed

in the network video management software.

For information specific to the HD Multisensor Dome Cameras, see HD Multisensor Dome Camera on page20.

For the settings that are specific to PTZ cameras, see PTZ Camera on page22.

For the settings that are specific to encoders, see Encoder on page24.

General

When you select the Setup link, the first page you see is the General page. The General page allows you to set

the device identity.

1. In the Name field, give the device a meaningful name.

2. In the Location field, describe the device’s location.

3. Select the Disable camera status LEDs check box to disable the LEDs located on the device.

4. If your camera supports onboard storage, select how the camera keeps time.

lIf you prefer to manually set the camera’s date and time, enter the date, time and time zone on this

page. Select the Automatically adjust clock for Daylight Savings Time check box if required.

lIf you prefer to auto-synchronize the camera’s date and time with an NTP server, configure the NTP

server on the Network page. For more information, see Network on the facing page.

5. (HD Bullet Camera and HD Multisensor Dome Camera only) Select the Disable configuration ethernet port

check box to disable the secondary Ethernet port underneath the camera.

6. (H.264 HD Cameras and HD Bullet Cameras only) Select any of the Overlay Setting check boxes to display

and stamp that information on the camera's video stream. The options are:

lDisplay Date

lDisplay Name

lDisplay Time

lDisplay Location

lDisplay GMT Offset

7. Click Apply to save your settings.

6 Setup

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Avigilon Sicherheitskamera Handbücher

Avigilon

Avigilon 1.0W-H3-BO1-IR Bedienungsanleitung

Avigilon

Avigilon 8.0C-H6SL-BO1-IR Bedienungsanleitung

Avigilon

Avigilon 1.0-H3A-DO1 Bedienungsanleitung

Avigilon

Avigilon 1.0C-H4IRPTZ-DP45 Bedienungsanleitung

Avigilon

Avigilon H4A Series Bedienungsanleitung

Avigilon

Avigilon H4A-G-B Bedienungsanleitung

Avigilon

Avigilon H3-BO1-IR Bedienungsanleitung

Avigilon

Avigilon H3-DC1 Bedienungsanleitung

Avigilon

Avigilon 1.0-H3M-DO1 Bedienungsanleitung

Avigilon

Avigilon H4A-DO1, H4A-DO1-IR, H4A-DO2, H4A-G-DO1-IR Bedienungsanleitung

Avigilon

Avigilon 1.3L-H3-DC2 Bedienungsanleitung

Avigilon

Avigilon 1.0W-H3PTZ-DP20 Bedienungsanleitung

Avigilon

Avigilon 2.0W-H3PTZ-DP20 Bedienungsanleitung

Avigilon

Avigilon 2.0C-H6SL-D1 Bedienungsanleitung

Avigilon

Avigilon 1.0-H3-D1 Bedienungsanleitung

Avigilon

Avigilon 1.0C-H4PTZ-DC45 Bedienungsanleitung

Avigilon

Avigilon H4A-DP1 Bedienungsanleitung

Avigilon

Avigilon H5SL Series Bedienungsanleitung

Avigilon

Avigilon 30L-H4PRO-B Bedienungsanleitung

Avigilon

Avigilon H6M-D Bedienungsanleitung

Avigilon

Avigilon 1.0C-H4A-B1 Bedienungsanleitung

Avigilon

Avigilon H5A Bedienungsanleitung

Avigilon

Avigilon H5A-FE Series Bedienungsanleitung

Avigilon

Avigilon 12W-H3-4MH-DC1 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung