Avinity ABT-632 Bedienungsanleitung
Operating Instructions
Bedienungsanleitung
Mode d‘emploi
Instrucciones de uso
Руководство по эксплуатации
PURE IMAGE–PURESOUND –PUREPASSION
00107632
TX
RX
1 5
2 4
3
GOperating instruction
Avinity: High Performance Accessories –born
of apassion for audio/video entertainment.
High-quality workmanship and performance
emphasise our commitment to premium
accessories.
Take your time and read the following in-
structions and information completely.Keep
these operating instructions in asafe place
for future reference.
1.
Explanation of Warning Symbols and Notes
Warning
This symbol is used to indicate safety
instructions or to draw your attention to
specichazards and risks.
Note
This symbol is used to indicate additional
information or important notes.
2. Package Contents
•Bluetooth® transmitter/receiver,
2-in-1 adapter
•3.5 mm jack cable
•Micro-USB charging/connecting cable
•These operating instructions
3. Safety Notes
•The product is intended for private,
non-commercial use only.
•Protect the product from dirt, moisture
and overheating, and only use it in adry
environment.
•Do not use the product in the immediate
vicinity of heaters or other heat sources or
in direct sunlight.
•Do not allow yourself to be distracted by
the product, for example when driving ave-
hicle or operating sports equipment. Always
pay attention to the surrounding tracand
your environment.
•Do not drop the product and do not expose
it to any major shocks.
•Do not operate the product outside the
power limits given in the specications.
•Do not open the device or continue to
operate it if it becomes damaged.
•Since the battery is integrated and cannot
be removed, you will need to dispose of the
product as awhole. Do this in compliance
with the legal requirements.
•Dispose of packaging material immediately
according to locally applicable regulations.
•Do not modify the product in any way.
Doing so voids the warranty.
Warning –Rechargeable battery
•Only use suitable charging devices or
USB connections for charging.
•As arule, do not use charging devices
or USB connections that are defective
and do not try to repair them yourself.
•Do not overcharge the product or allow
the battery to completely discharge.
•Avoid storing, charging or using
batteries in extreme temperatures.
•When stored over along period of time,
batteries should be charged regularly
(at least every three months).
4.Getting Started
•The adapter is equipped with arecharge-
able battery.The battery must be fully
charged before using the device for the
rst time.
•Begin charging by connecting the included
Micro-USB charging/connecting cable to
the adapter’s Micro-USB connection (5)
and to asuitable USB charger.Please refer
to the operating instructions for the USB
charger used.
•The adapter’s status LED (3) emits acon-
stant red light during charging.
•It can take up to 2hours to fully charge the
battery.
•Charging begins and ends automatically.
5. Operation
5.1. Switching the adapter on/o
•Switching on:
With the device o,press and hold the
multifunction button (2) for 3seconds. The
status LED (3) lights up in blue.
•Switching o:
With the device on, press and hold the
multifunction button (2) for 3seconds. The
status LED (3) emits two red ashes before
the device turns o.
The rst time the device is turned on, pairing
is automatically started –see 5.2 Blue-
tooth®pairing in receiver (RX) mode.
5.2.
Bluetooth®pairing in receiver (RX) mode
Note –Pairing
•Make sure that your Bluetooth®-ca-
pable terminal device is on and
Bluetooth® is activated.
•For more information, please refer
to the operating instructions of your
terminal device.
•Connect your terminal device to the adapt-
er using the included 3.5 mm jack cable
and the audio connection (AUX) (4).
•Select the adapter’s RX mode by moving
the switch (1) to the right.
•The adapter and the terminal device should
be no further than 1metre apart. The short-
er the distance, the better.
•With the adapter on, press the multifunc-
tion button (2) twice. After approximately
3seconds, the status LED (3) will emit
ashes of alternating blue and red light to
indicate the device is in pairing mode.
•Open the Bluetooth®settings on your
terminal device and wait until Avinity
BTT-632 appears in the list of Bluetooth®
devices found.
•Select Avinity BTT-632 and wait until the
adapter is listed as connected in the Blue-
tooth®settings on your terminal device.
Note –Bluetooth®password
Some terminal devices require a
password in order to connect to another
Bluetooth®device.
•If your terminal device requests a
password to establish the connection,
enter 0000, 1234, 1111 or 8888.
Note
If pairing was successful, the status LED
(3) lights up in blue.
•Youcan now use the adapter.
5.3. Bluetooth®pairing in transmitter (TX)
mode
Note –Pairing
•Make sure that your Bluetooth®-
capable terminal device is on and
Bluetooth® is activated.
•For more information, please refer
to the operating instructions of your
terminal device.
•Connect your terminal device to the adapt-
er using the included 3.5 mm jack cable
and the audio connection (AUX) (4).
•Select the adapter’s TX mode by moving
the switch (1) to the left.
•Turn on Bluetooth®on your Bluetooth®
headphones/speaker.
•For more information, please refer to the
operating instructions of your terminal
device.
•The adapter and the Bluetooth®headphones/
speaker should be no further than 1metre
apart. The shorter the distance, the better.
•With the adapter on, press the multifunc-
tion button (2) twice. After approximately
3seconds, the status LED (3) will emit
ashes of blue light to indicate the device
is in pairing mode.
•The connection is now established auto-
matically.
5.4. Automatic Bluetooth®connection
(after successful pairing)
Note –Pairing
•Make sure that your Bluetooth®-
capable terminal device is on and
Bluetooth® is activated.
•For more information, please refer
to the operating instructions of your
terminal device.
•Make sure that the adapter is on.
•After the devices have been paired once, the
connection is then established automatically.
•Youcan now use the adapter.
Note
•If pairing was successful, the status
LED (3) will be lit blue.
•It may be necessary to make settings
on your terminal device to enable auto-
matic connection to the paired adapter.
Note –Connection impaired
After the devices have been paired
once, the connection is then estab-
lished automatically.Ifthe Bluetooth®
connection is not established automati-
cally,check the following:
•Check the Bluetooth® settings of your
terminal device to see whether Avinity
BTT-632 is connected.
•If not, repeat the steps listed in 5.2
Bluetooth® pairing.
•Check whether obstacles are impairing
the range. If so, move the devices
closer together.
•The performance can also be aected
by aweak battery.
5.5. Pairing in transmitter (TX) mode with
two devices at the same time
•Switch on the adapter and your two
Bluetooth®-capable audio devices (BT
headphones/speaker) as described in 5.2
Bluetooth®pairing.
•The adapter automatically names the two
terminal devices Aand B, and establishes a
connection.
5.6. Deleting the pairing list
•Switch othe adapter in the current mode
(TX or RX). After approximately 3seconds,
move the switch (1) to the other mode
and switch the adapter on again; this will
delete all paired devices from the list.
5.7. Battery capacity
•The status LED (3) begins ashing red when
the battery charge is low.
•Charge the adapter as described in 4.
Getting started.
6. Care and Maintenance
Only clean this product with aslightly damp,
lint-free cloth and do not use aggressive
cleaning agents.
7. Warranty Disclaimer
Hama GmbH &Co. KG assumes no liability
and provides no warranty for damage result-
ing from improper installation/mounting,
improper use of the product or from failure
to observe the operating instructions and/or
safety notes.
8. Service and Support
Please contact Hama Product Consulting if
you have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found
here: www.hama.com
9. Technical Data
Bluetooth®version 4.1
Prole A2DP
Range <10m
Battery type
Lithium polymer
rechargeable
battery
Frequency band(s)
2402 –2480 MHz
Maximum radio-
frequency power
transmitted
3.94 mW E.I.R.P.
Input 240 mA
Charging time Approx. 2h
Battery life of Blue-
tooth®transmitter Approx. 13 h
Battery life of
Bluetooth®receiver Approx. 12 h
10. Recycling Information
Note on environmental protection:
After the implementation of the
European Directive 2012/19/EU and
2006/66/EU in the national legal
system, the following applies: Electric
and electronic devices as well as batteries
must not be disposed of with household
waste. Consumers are obliged by law to return
electrical and electronic devices as well as
batteries at the end of their service lives to
the public collecting points set up for this
purpose or point of sale. Details to this are
dened by the national law of the respective
country.This symbol on the product, the
instruction manual or the package indicates
that aproduct is subject to these regulations.
By recycling, reusing the materials or other
forms of utilising old devices/Batteries, you
are making an important contribution to
protecting our environment.
11. Declaration of Conformity
Hereby,Hama GmbH &CoKGdeclares
that the radio equipment type
[00107632] is in compliance with
Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the
following internet address:
www.hama.com->00107632-> Downloads.
DBedienungsanleitung
Avinity: High Performance Accessories –
geboren aus der Leidenschaft für Audio/Video
Entertainment. Hochwertige Verarbeitung und
Performance unterstreichen unseren Anspruch
an Premium Zubehör.
Nehmen Sie sich Zeit und lesen Sie die folgen-
den Anweisungen und Hinweise zunächst ganz
durch. Bewahren Sie diese Bedienungsanlei-
tung anschließend an einem sicheren Ort auf,
um bei Bedarf darin nachschlagen zu können.
1.
Erklärung von Warnsymbolen und Hinweisen
Warnung
Wird verwendet, um Sicherheitshinweise
zu kennzeichnen oder um Aufmerksam-
keit auf besondere Gefahren und Risiken
zu lenken.
Hinweis
Wird verwendet, um zusätzlich Infor-
mationen oder wichtige Hinweise zu
kennzeichnen.
2. Packungsinhalt
•Bluetooth®-Sender/-Empfänger,
2in1-Adapter
•3,5-mm-Klinkenkabel
•Micro-USB-Lade-/Verbindungskabel
•diese Bedienungsanleitung
3. Sicherheitshinweise
•Das Produkt ist für den privaten, nicht-ge-
werblichen Haushaltsgebrauch vorgesehen.
•Schützen Sie das Produkt vor Schmutz,
Feuchtigkeit und Überhitzung und verwen-
den Sie es nur in trockenen Umgebungen.
•Betreiben Sie das Produkt nicht in unmittel-
barer Nähe der Heizung, anderer Hitzequel-
len oder in direkter Sonneneinstrahlung.
•Lassen Sie sich auf der Fahrt mit einem
Kraftfahrzeug oder Sportgerät nicht durch
Ihr Produkt ablenken und achten Sie auf die
Verkehrslage und Ihre Umgebung.
•Lassen sie das Produkt nicht fallen und
setzen Sie es keinen heftigen Erschütterun-
gen aus.
•Betreiben Sie das Produkt nicht außerhalb
seiner in den technischen Daten angegebe-
nen Leistungsgrenzen.
•Önen Sie das Produkt nicht und betreiben
Sie es bei Beschädigung nicht weiter.
•Der Akku ist fest eingebaut und kann nicht
entfernt werden, entsorgen Sie das Produkt
als Ganzes gemäß den gesetzlichen Bestim-
mungen.
•Entsorgen Sie das Verpackungsmaterial
sofort gemäß den örtlich gültigen Entsor-
gungsvorschriften.
•Nehmen Sie keine Veränderungen am Gerät
vor.Dadurch verlieren Sie jegliche Gewähr-
leistungsansprüche.
Warnung –Akku
•Verwenden Sie nur geeignete Ladegerä-
te oder USB-Anschlüsse zum Auaden.
•Verwenden Sie defekte Ladegeräte oder
USB-Anschlüsse generell nicht mehr und
versuchen Sie nicht, diese zu reparieren.
•Überladen oder tiefentladen Sie das
Produkt nicht.
•Vermeiden Sie Lagerung, Laden und
Benutzung bei extremen Temperaturen.
•Laden Sie bei längerer Lagerung regel-
mäßig (mind. vierteljährig) nach.
4. Inbetriebnahme
•Der Adapter verfügt über einen wieder auad-
baren Akku. Vorder ersten Anwendung muss
der Akku vollständig aufgeladen werden.
•Starten Sie den Ladevorgang, indem Sie das
beiliegende Micro-USB-Lade-/Verbindungs-
kabel an den Micro-USB-Anschluss (5) des
Adapters und an ein geeignetes USB-La-
degerät anschließen. Beachten Sie hierzu
die Bedienungsanleitung des verwendeten
USB-Ladegeräts.
•Die Status-LED (3) des Adapters leuchtet
während des Ladevorgangs dauerhaft rot.
•Es kann bis zu 2Stunden dauern, bis der
Akku vollständig geladen ist.
•Der Ladevorgang startet und endet automa-
tisch.
5.Betrieb
5.1. Ein-/Ausschalten des Adapters
•Einschalten:
Halten Sie im ausgeschalteten Zustand die
Multifunktionstaste (2) 3Sekunden lang ge-
drückt. Die Status-LED (3) leuchtet blau auf.
•Ausschalten:
Halten Sie im eingeschalteten Zustand die
Multifunktionstaste (2) 3Sekunden lang
gedrückt. Die Status-LED (3) leuchtet 2x rot
auf, bevor sich das Gerät abschaltet.
Beim ersten Einschalten wird automatisch
das Pairing gestartet –siehe 5.2. Bluetooth®
Erstverbindung (Pairing) im Empfänger-Mo-
dus RX.
5.2. Bluetooth®Erstverbindung (Pairing) im
Empfänger-Modus RX
Hinweis –Pairing
•Stellen Sie sicher,dass Ihr Bluetooth®-
fähiges Endgerät eingeschaltet ist und
dass Bluetooth® aktiviert ist.
•Beachten Sie hierzu die
Bedienungsanleitung Ihres Endgerätes.
•Für die Verbindung zum jeweiligen Endgerät
verbinden Sie es über das beiliegende
3,5 mm-Klinkenkabel und den Audio-An-
schluss (AUX) (4) mit dem Adapter.
•Wählen Sie den RX-Modus des Adapters,
indem Sie den Umschalter (1) nach rechts
schieben.
•Der Adapter und das Endgerät sollen nicht
weiter als 1Meter voneinander entfernt
sein. Je geringer der Abstand, desto besser.
•Drücken Sie zwei Mal die Multifunktionstas-
te (2) des eingeschalteten Adapters. Nach
ca. 3Sekunden blinkt die Status-LED (3)
abwechselnd blau und rot und signalisiert
dadurch den Kopplungsmodus.
Inhaltsverzeichnis
Sprachen:
