AWID LR-3200 Montageanleitung

LR-3200 Reader Installation Sheet Version 1.0 Page 1 of 2

Installation Sheet (Wiegand Interface)

LR-3200 UHF Reader

These instructions are for AWID’s Model LR-3200 Long Range Reader, using compatible UHF credentials from

AWID. This guide describes installation using the Wiegand interface. For RS-232 interface, download AWID’s

Technical Reference.

Preparation

Reader Location: Select the reader’s mounting location. The LR-3200 Reader may be screwed to a pole,

pedestal, or flat surface with appropriate mounting hardware (LR-MB-0-0). Mounted on a metal surface; the

read range may be reduced.

DC Power Supply: A separate dedicated DC Power Supply for each LR-3200 Reader. Do not draw the

reader’s power from the system’s controller. Nominal 12 volts DC supply to the reader. Current capacity

needed; 3 amperes or more.

Cable: May be separate for data and for power, or may be combined for data and power together.

Max. length = 500 ft.

Power Alone – 18 gauge, 2 conductors, stranded wires, color-coded, overall shielded, high quality.

Data Alone – 22 gauge, 3 conductors, stranded wires, not twisted pairs, overall shielded, high quality.

Combined Cable – 18 gauge, 5 conductors, stranded wires, not twisted pairs, overall shielded, high quality.

If cables are pulled through metal conduit, the conduit should be earth-grounded.

Figure 1

LR-3200 Reader Installation Sheet Version 1.0 Page 2 of 2

Procedure

Mounting the Reader

1. Fasten the mounting bracket to the pole, post, pedestal or wall. Leave space for the reader unit’s pan-

and-tilt adjustment.

2. Fasten the reader to the bracket with 2 ¼”-20 screws. AWID’s LR-MB-0-0 bracket includes fasteners.

3. Aim the reader toward the location of tags when they are attached to vehicles, for the planned reading

distance.

Wiring the LR-3200 (Figure 1)

1. Cut off the 10-pin connector from the end of the reader’s cable and discard the connector.

2. Check the power supply and cable(s) for power and data. Be certain that they meet AWID’s Specifications.

3. Connect Yellow to Black at the reader; Black and Red to the power supply; Green and White and Blue

to the controller.

4. Connect the readers Drain/Shield wire to the shields of all cables. Do not ground drain and shields –

they must float.

Yellow Wire - Arming circuit – If you are not using a arming circuit, connect the yellow wire to the

black wire at the reader permanently. For control of the reader’s RF transmission by a vehicle sensor,

connect the yellow wire to the relay contacts of the vehicle sensor (IR Sensor, Ground Loop). To disarm

the reader (no RF transmission), do not connect yellow wire.

Blue Wire - The blue wire is Wiegand Data Common. It connects where a proximity reader’s black wire would

connect on that reader port. The terminal is usually labeled “Ground”. If there is a “Data Common” terminal on

that reader port, connect the blue wire there instead of “Ground”.

Testing the Completed System

Once mounting and wiring is completed, power up the LR-3200 and check that the Red LED is illuminated.

Drive a vehicle/walk with an attached tag into the read-zone on the lane. Observe the Green LED activity light,

good reads are indicated by blinking from the Green LED.

For Additional Assistance

• • • In the U.S. call Technical Support, +1-408-825-1100 • • •

Talk with AWID Technical Support | | Website: www.awid.com ||E-mail: support@awid.com

Inhaltsverzeichnis

Andere AWID Kartenleser Handbücher

AWID

AWID LR-2200 Bedienungsanleitung

AWID

AWID UA-612 Montageanleitung

AWID

AWID SENTINEL-PROX LR-2000 Bedienungsanleitung

AWID

AWID MPR-3014WF-QB Bedienungsanleitung

AWID

AWID XK-3640 Montageanleitung

AWID

AWID Sentinel-Prox DC-1023 Montageanleitung

AWID

AWID Sentinel-Sense ADB-512 Bedienungsanleitung

AWID

AWID XR-3600 Montageanleitung

AWID

AWID SENTINEL-PROX DK-1025 Bedienungsanleitung

AWID

AWID SR-2400 Montageanleitung

AWID

AWID SENTINEL-PROX SC-2300 Bedienungsanleitung

AWID

AWID MR-1824HiLo Montageanleitung

AWID

AWID SP-6820 Montageanleitung

AWID

AWID SENTINEL-PROX MR-1824 Montageanleitung

AWID

AWID SENTINEL-PROX LR-911 Bedienungsanleitung

AWID

AWID uAxcess XJ-1023 Bedienungsanleitung

AWID

AWID LR-3000 Bedienungsanleitung

AWID

AWID MM-6800 Montageanleitung

AWID

AWID SENTINEL-PROX LR-911 Bedienungsanleitung

AWID

AWID SR-2400 Montageanleitung

AWID

AWID Sentinel-Prox MR-1824HiLo Montageanleitung

AWID

AWID SR-2400 Montageanleitung

AWID

AWID MPR-5005 Bedienungsanleitung

AWID

AWID KP-6840 Montageanleitung

Beliebte Kartenleser Handbücher anderer Marken

Lindy

Lindy 43185 Bedienungsanleitung

Lindy

Lindy 43185 Bedienungsanleitung

ViziT

ViziT RD-4F Bedienungsanleitung

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Bedienungsanleitung

AVID ID

AVID ID AVID1043 Bedienungsanleitung

Conrad

Conrad PCMCIA Bedienungsanleitung

Rosslare

Rosslare DR-6255 Bedienungsanleitung

Lindy

Lindy 51541 Bedienungsanleitung

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Bedienungsanleitung

Johnson Controls

Johnson Controls Kantech tyco ioSmart Bedienungsanleitung

ACS

ACS ACR122L Bedienungsanleitung

Secukey

Secukey S2-MF Bedienungsanleitung

Elecom

Elecom MR-SMC07 series Bedienungsanleitung

Alien

Alien ALR-9800 Bedienungsanleitung

ACS

ACS ACR310 Bedienungsanleitung

Datamars

Datamars R-IN1300 MID Bedienungsanleitung

Alarm Lock

Alarm Lock AL-PRE2 Bedienungsanleitung

xpr

xpr B100PROX-AH Benutzerhandbuch