AXIOMTEK MPC225-873 Series Bedienungsanleitung

MPC225-873 Series

22”TFT Fanless Medical Grade

Panel Computer with Intel®CoreTM

i7/i5/i3 Processors

User’s Manual

Disclaimers

This manual has been carefully checked and believed to contain accurate information.

Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third

party’s rights, and any liability arising from such use.

Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,

completeness or usefulness of any information in this document. Axiomtek does not make any

commitment to update the information in this manual.

Axiomtek reserves the right to change or revise this document and/or product at any time

without notice.

No part of this document may be reproduced, stored in a retrieval system, or transmitted, in

any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written permission of Axiomtek Co., Ltd.

June 2017, Version A2

Printed in Taiwan

iii

Safety Approvals

CE Marking

EN60601-1, UL60601-1

FCC Class B

FCC Compliance

This equipment has been tested in compliance with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are meant to provide reasonable protection

against harmful interference in a residential installation. If not installed and used in accordance

with proper instructions, this equipment might generate or radiate radio frequency energy and

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following methods:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment to another outlet of a circuit that doesn’t connect with the

receiver.

4. Consult the dealer or an experienced radio/TV technician for help.

Shielded interface cables must be used in order to comply with the emission limits.

Safety Precautions

Before getting started, please read the following important safety precautions.

1. The MPC225-873 Series does not come equipped with an operating system. An

operating system must be loaded first before installing any software into the computer.

2. Be sure to ground yourself to prevent static charge when installing the internal

components. Use a grounding wrist strap and place all electronic components in any

static-shielded devices. Most electronic components are sensitive to static electrical

charge.

3. Disconnect the power cord from the MPC225-873 Series before making any installation.

Be sure both the system and external devices are turned OFF. A sudden surge of power

could ruin sensitive components. Make sure the MPC225-873 Series is properly

grounded.

4. Make sure the voltage of the power source is correct before connecting the equipment to

the power outlet.

5. The brightness of the flat panel display will be getting weaker as a result of frequent

usage. However, the operating period varies depending on the application environment.

6. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not

spray any liquid cleaner directly onto the screen. The MPC225-873 Series may come

with or w/o a touchscreen. Although the touchscreen is chemical resistant, it is

recommended that you spray the liquid cleaner on a cloth first before wiping the screen.

In case your system comes without the touchscreen, you must follow the same

procedure and not spray any cleaner on the flat panel directly.

7. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen may

cause malfunction or internal failure to the touchscreen.

8. The flat panel display is not susceptible to shock or vibration. When assembling the

MPC225-873 Series, make sure it is securely installed.

9. Do not leave this equipment in an uncontrolled environment where the storage

temperature is below -20°C or above 60°C. It may damage the equipment.

10. External equipment intended for connection to signal input/out or other connectors shall

comply with relevant UL/IEC standard.

11. Do not open the system’s back cover. If opening the cover for maintenance is a must,

only a trained technician is allowed to do so. Integrated circuits on computer boards are

sensitive to static electricity. To avoid damaging chips from electrostatic discharge,

observe the following precautions:

Before handling a board or integrated circuit, touch an unpainted portion of the

system unit chassis for a few seconds. This will help to discharge any static

electricity on your body.

When handling boards and components, wear a wrist-grounding strap, available

from most electronic component stores.

Important Safety Instructions

Read before operating equipment.

This product was designed and manufactured to meet strict quality and safety standards.

There are, however, some installation and operation precautions which you should be

particularly aware of.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Classification Class I ME Equipment.

6. External power adapter, Input : 100~240Vac, 50~60Hz.

7. The medical panel computer is certified with medical certifications to meet medical grade

approval standards. The fanless design and against enclosure allow it to operate reliably

and quietly, it applied in any medical environments.

8. WARNING: To avoid risk of electric shock, this equipment must only be connected to a

supply mains with protective earth.

9. Accessory equipment connected to the analog and digital interfaces must be in

compliance with the respective nationally harmonized IEC standards (i.e. IEC 60601-1

for medical equipment, IEC 60950-1 for ITE equipment). Furthermore all configurations

shall comply with the system standard in IEC 60601-1. Anyone who connects additional

equipment to the signal input part or signal output part is configuring a medical system,

and is therefore, responsible that the system complies with the requirements of the

system standard IEC 60601-1.

10. Power supply is specified as a part of ME EQUIPMENT.

11. For pluggable equipment, the mains connector shall be installed near the equipment and

shall be easily accessible.

12. Follow the national requirement to dispose unit/accessories/waste products/residues etc.

13. WARNING: Do not modify this equipment without authorization of the manufacturer.

14. WARNING: The operator must not touch the connectors and the patient at the same

time.

Classification

1. Degree of production against electric shock: Not classified.

2. Degree of protection against the ingress of water: IPX1.

3. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air

or with oxygen or nitrous oxide.

4. Mode of operation: Continuous.

5. Type of protection against electric shock: Class I equipment.

General Cleaning Tips

You may need the following precautions before you begin to clean the computer. When you

clean any single part or component for the computer, please read and understand the details

below fully.

1. When you need to clean the device, please rub it with a piece of dry cloth.

2. Be cautious of the tiny removable components when you use a vacuum cleaner to

absorb the dirt on the floor.

3. Turn the system off before you start to clean up the component or computer.

4. Never drop the components inside the computer or get circuit board damp or wet.

5. Be cautious of all kinds of cleaning solvents or chemicals when you use it for the sake of

cleaning. Some individuals may be allergic to the ingredients.

6. Try not to put any food, drink or cigarette around the computer.

vii

Cleaning Tools

Although many companies have created products to help improve the process of cleaning your

computer and peripherals, users can also use household items to clean their computers and

peripherals. Below is a listing of items you may need or want to use while cleaning your

computer or computer peripherals.

Keep in mind that some components in your computer may only be able to be cleaned using a

product designed for cleaning that component, if this is the case it will be mentioned in the

cleaning.

Cloth: A piece of cloth is the best tool to use when rubbing up a component. Although

paper towels or tissues can be used on most hardware as well, we still recommend you

to rub it with a piece of cloth.

Water or rubbing alcohol: You may moisten a piece of cloth a bit with some water or

rubbing alcohol and rub it on the computer. Unknown solvents may be harmful to the

plastics parts.

Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles, and other particles out of

a computer can be one of the best methods of cleaning a computer. Over time these

items can restrict the airflow in a computer and cause circuitry to corrode.

Cotton swabs: Cotton swaps moistened with rubbing alcohol or water are excellent tools

for wiping hard to reach areas in your keyboard, mouse, and other locations.

Foam swabs: Whenever possible it is better to use lint free swabs such as foam swabs.

Note

We strongly recommend that you should shut down the system before you start to

clean any single components.

Please follow the steps below:

1. Close all application programs.

2. Close operating software.

3. Turn off power switch.

4. Remove all devices.

5. Pull out power cable.

viii

Scrap Computer Recycling

If the computer equipments need the maintenance or are beyond repair, we strongly

recommend that you should inform your Axiomtek distributor as soon as possible for the

suitable solution. For the computers that are no longer useful or no longer working well, please

contact your Axiomtek distributor for recycling and we will make the proper arrangement.

Trademarks Acknowledgments

Axiomtek is a trademark of Axiomtek Co., Ltd.

AMI is trademark of American Megatrend Inc.

IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.

Intel®and Pentium®are registered trademarks of Intel Corporation.

Other brand names and trademarks are the properties and registered brands of their

respective owners.

Table of Contents

Disclaimers.....................................................................................................ii

Safety Approvals...........................................................................................iii

Safety Precautions........................................................................................iv

Important Safety Instructions .......................................................................v

Classification.................................................................................................vi

General Cleaning Tips ..................................................................................vi

Cleaning Tools .............................................................................................vii

Scrap Computer Recycling........................................................................viii

Chapter 1 Introduction............................................. 1

1.1 Features...............................................................................................1

1.2 Specifications......................................................................................2

1.3 Dimensions..........................................................................................4

1.4 I/O Outlets............................................................................................6

1.5 Package Checklist...............................................................................8

Chapter 2 Hardware Installation ............................. 9

2.1 Installing CPU and DRAM...................................................................9

2.2 Installing Hard Disk Drive.................................................................13

2.3 Serial Port Interfaces ........................................................................17

2.4 Installing PCI-Express Mini Card.....................................................17

2.5 Installing Add-on Card (Optional)....................................................21

2.6 Mounting............................................................................................24

2.6.1 Wall Mounting............................................................................................ 24

2.6.2 VESA-Arm Mounting................................................................................. 25

2.6.3 Desktop Stand Mounting (Optional).......................................................... 25

Chapter 3 AMI BIOS Setup Utility .......................... 29

3.1 Starting...............................................................................................29

3.2 Navigation Keys ................................................................................29

3.3 Main Menu..........................................................................................30

3.4 Advanced Menu.................................................................................31

3.5 Chipset Menu.....................................................................................41

3.6 Boot Menu..........................................................................................46

3.7 Security Menu....................................................................................47

3.8 Save & Exit Menu ..............................................................................48

Chapter 4 Drivers Installation................................ 51

4.1 System Drivers..................................................................................51

4.2 Touch Screen.....................................................................................52

4.2.1 Specifications ............................................................................................ 52

4.2.2 Installing Touch Screen............................................................................. 52

4.3 OSD Sync Service.............................................................................55

4.3.1 Installing OSD Sync .................................................................................. 55

4.3.2 OSD Function Keys................................................................................... 56

4.3.3 OSD Notification Bar................................................................................. 57

4.3.4 Uninstalling OSD Sync.............................................................................. 58

Appendix A Watchdog Timer .................................... 61

A.1 About Watchdog Timer.....................................................................61

A.2 How to Use Watchdog Timer............................................................61

Appendix B Digital I/O............................................... 63

B.1 Digital I/O Software Programming ...................................................63

Appendix C iAMT Settings........................................ 65

C.1 Entering MEBx...................................................................................65

C.2 Set and Change Password...............................................................66

C.3 Intel®iAMT Web Console..................................................................68

Appendix D Note ....................................................... 71

Appendix E EMC Statement ..................................... 73

Appendix F TPM Statement....................................... 77

Inhaltsverzeichnis

Andere AXIOMTEK Touchscreen Handbücher

AXIOMTEK

AXIOMTEK MPC175-873 Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK PANEL5155-807 Bedienungsanleitung

AXIOMTEK

AXIOMTEK MPC153-834 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT815L-511 Bedienungsanleitung

AXIOMTEK

AXIOMTEK IFO2225-830 Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK P1197E-861 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT-3106TL-830 Bedienungsanleitung

AXIOMTEK

AXIOMTEK IFO2225-873 Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK ITC150WM Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT5152T-832 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT318A-ELK-WCD Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT3156T-832 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT-3126TL-830 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT-3156TL-830 Bedienungsanleitung

AXIOMTEK

AXIOMTEK MPC103-845 Bedienungsanleitung

AXIOMTEK

AXIOMTEK IFO2225-851 Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK MPC225-851 Series Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT321W-502-PCT/FR Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT315W-521-PCT Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT3126T-834 Bedienungsanleitung

AXIOMTEK

AXIOMTEK PANEL5150-675 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT3187W-832-PCT Bedienungsanleitung

AXIOMTEK

AXIOMTEK MPC240 Bedienungsanleitung

AXIOMTEK

AXIOMTEK GOT5840T-832 Bedienungsanleitung

Beliebte Touchscreen Handbücher anderer Marken

FlowLine

FlowLine Data loop Bedienungsanleitung

ALPEX

ALPEX AEx-8 P Series Bedienungsanleitung

Ltech

Ltech E5S Bedienungsanleitung

Harman

Harman AMX MODERO S MSD-701-L2 Bedienungsanleitung

Acnodes

Acnodes PC 1150 Bedienungsanleitung

AIS

AIS IP10IA99 series Bedienungsanleitung

IBASE Technology

IBASE Technology ASTUT-152-RE1S Bedienungsanleitung

YASKAWA

YASKAWA TP 610C Bedienungsanleitung

B&R

B&R Power Panel C Series Bedienungsanleitung

Beijer Electronics

Beijer Electronics X2 control Bedienungsanleitung

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Bedienungsanleitung

Qomo

Qomo QIT1386 Bedienungsanleitung

DFI

DFI KS104-CD Bedienungsanleitung

AMX

AMX AXP-PPC Leitfaden

Sartorius

Sartorius X3 PR 5410 Bedienungsanleitung

AMX

AMX Modero X Series Bedienungsanleitung

Advantech

Advantech TPC-30 Series Bedienungsanleitung

B&R Industries

B&R Industries MAPPC900-ENG Bedienungsanleitung