Axis Axis 216FD Bedienungsanleitung

ENGLISH FRANCAIS DEUTSCH ESPAÑOL ITALIANO

AXIS 216FD Fixed Dome

Network Camera

Installation Guide

AXIS 216FD Installation Guide Page 3

ENGLISH

AXIS 216FD

Fixed Dome Network Camera

Installation Guide

This installation guide provides instructions for installing the AXIS 216FD Fixed Dome

Network Camera on your network. For all other aspects of using the product, please see the

AXIS 216FD User’s Manual, available from www.axis.com or on the Axis Network Video

Product CD.

Installation steps

1. Check the package contents against the list below.

2. Install the hardware - page 4

3. Set the IP address - page 7

4. Set the password - page 13

5. Adjust the image - page 14

Package contents

Item Title/Variants

Fixed Dome Network Camera AXIS 216FD

Indoor power adapter

Note: The power adapter is country spe-

cific, please check that the type of power

adapter you are using is correct

Europe

Australia

USA/Japan

Argentina

Korea

Extension cable 1.8m (5.9 ft) Power cable

Terminal block connector 4-pin I/O connector block

Mounting kit Screwdriver for tamper-proof screws

Tamper-proof screws

Drill template

Documentation AXIS 216FD Installation Guide

Axis Network Video Product CD

Warranty document

Important!

This product must be installed in

compliance with local laws and

regulations.

Page 4 AXIS 216FD Installation Guide

Installing the hardware

Refer to the illustration on page 5 for a detailed overview of the AXIS 216FD.

1. Make a note of the serial number (S/N), which is located on the product label on the base

of the unit casing. The serial number is used in the installation.

2. Using the drill template, drill two holes in the ceiling/wall.

3. Install the camera unit on the ceiling/wall using screws and plugs that are appropriate for

the ceiling/wall material.

Notes:

• The AXIS 216FD is designed for indoor use only.

• The AXIS 216FD can be mounted with the network and power cables routed through the wall/ceiling or through

the sides. There are cover plates for the openings on both sides of the dome cover.

• Ensure the camera is placed so that the tamper-proof screws can be tightened using the supplied screw driver.

Connecting the cables

1. Connect the network cable to the camera’s network connector.

2. Connect power using one of the methods listed below:

• PoE (Power over Ethernet) via the network cable. This will automatically be detected if

available via the network.

• Connect the supplied indoor power adapter to the power connector on the camera unit.

3. Check that the network, status and power indicators (LEDs) light up green. See the table on

page 6 for LED descriptions.

4. Refer to “Setting the IP address” on page 7 for information on how to assign an IP address

to the AXIS 216FD.

AXIS 216FD Installation Guide Page 5

ENGLISH

Description

Network

connector Serial number (S/N)

Please make a note of the

The serial number is required

during the installation.

serial number and retain

for future reference.

Power

I/O terminal

connector

Dome casing

connector

Camera unit

Power

indicator

Network

indicator

Audio out

Audio in

Status

indicator

Microphone

(LED)

Control

button

Cover

plates

Page 6 AXIS 216FD Installation Guide

I/O terminal connector block

LED indicators

Pin Function Description

4 Transistor

Output

With a maximum load of 50mA and a maximum voltage of 24V DC, this output has an

open-collector NPN transistor with the emitter connected to the GND pin. If used with an

external relay, a diode must be

connected in parallel with the load, for protection against voltage

transients.

3 Digital Input Connect to GND to activate, or leave floating (or unconnected) to

deactivate.

23.3VDC

Can be used to power auxiliary equipment, max 50mA.

1GND

LED Color Description

Network Green Steady for connection to 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No connection.

Status Green Shows steady green for normal operation.

Note: The Status LED can be configured to be unlit during normal operation, or to flash only when

the camera is accessed. See the online help files for more information. Go to Setup > System

Options > LED settings

Amber Steady during startup, reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

AXIS 216FD Installation Guide Page 7

ENGLISH

Setting the IP address

The AXIS 216FD is designed for use on an Ethernet network and must be assigned an IP

address to make it accessible.

Windows

Notes:

• The AXIS 216FD has the default IP address 192.168.0.90

• To view the admin pages for the DHCP server, please see the server’s own documentation. You may need to

contact your network administrator.

• If setting the IP address fails, check that there is no firewall blocking the operation.

See page 10 for other available methods for setting or discovering the IP address of the

AXIS 216FD, e.g. in other operating systems.

AXIS IP Utility and AXIS Camera Management are the recommended methods for setting an IP address in Windows.

DHCP Server

in network

Operating system Recommended

method for:

AXIS IP Utility

See page 8

Optional Windows Single camera /

small installations

AXIS Camera Management

See page 9

Optional Windows 2000

Windows XP Pro

Windows 2003 Server

Multiple cameras /

large installations

Requirements

Installation methods

Page 8 AXIS 216FD Installation Guide

AXIS IP Utility

AXIS IP Utility automatically discovers and displays Axis devices on your network. The

application can also be used to manually set a static IP address. AXIS IP Utility is available on

the Axis Network Video Product CD, or it can be downloaded from www.axis.com/techsup

Note that you must install the AXIS 216FD on the same network segment (physical subnet) as

the computer running AXIS IP Utility.

Automatic discovery

1. Check that the AXIS 216FD is con-

nected to the network and that power

has been applied.

2. Start AXIS IP Utility.

When the AXIS 216FD appears in the

window, double-click it to open the

camera’s home page.

3. See page 13 for instructions on how to

set the password.

Set the IP address manually

1. Acquire an unused IP address on the

same network segment your computer

is connected to.

2. Click the button Set IP address using serial number and enter the serial number and

IP address for the AXIS 216FD. The serial number is located on the product label.

3. Click the Set IP button and follow the instructions.

4. Click View Home Page to access the AXIS 216FD web pages.

5. See page 13 for instructions on how to set the password.

Single camera / small installations

Notes:

Set the IP address using IP Utility within 2 minutes of starting

the camera.

AXIS IP Utility can be used to change a dynamically set

IP address to a static one.

AXIS 216FD Installation Guide Page 9

ENGLISH

AXIS Camera Management

AXIS Camera Management can automatically find and set IP addresses, show connection

status and manage firmware upgrades of multiple Axis video products. AXIS Camera

Management is available on the Axis Network Video Product CD, or can be downloaded from

www.axis.com/techsup

Set the IP address

1. Check that the AXIS 216FD is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the AXIS 216FD appears in the window, double-

click it to open the camera’s home page.

3. See page 13 for instructions on how to set the password.

Set the IP address in multiple devices

AXIS Camera Management speeds up the process of assigning IP addresses in multiple devices

by suggesting available IP addresses from a specified range.

Select the devices that you want to configure (you can even select different models) and click

the Assign IP icon.

Enter the range of IP addresses, the subnet mask and default router that the devices can use.

Click Find and the program will search in the specified range and suggest an available IP

address for each device.

Multiple cameras / large installations

Page 10 AXIS 216FD Installation Guide

Other available methods

This table shows alternative methods for setting or discovering the IP address.

Notes:

•UPnP™, DHCP and Bonjour are enabled by default in the AXIS 216FD.

• The AXIS 216FD has the default IP address 192.168.0.90

• To view the admin pages for the DHCP server, please see the server’s own documentation. You may need to

contact your network administrator.

• If setting the IP address fails, check that there is no firewall blocking the operation.

•AXIS Dynamic DNS Service requires an Internet connection without an HTTP proxy.

•Bonjour - applicable only in browsers with support for Bonjour, e.g. Safari.

UPnP™

UPnP™ functionality is enabled by default in the AXIS 216FD. If also enabled on your computer

(Windows ME or XP), the camera will automatically be detected and a new icon will be added

to “My Network Places.” Click this icon to access the AXIS 216FD. See also page 13 for

instructions on how to set the password.

Note that you must install the AXIS 216FD on the same network segment (physical subnet) as

the computer handling the installation.

Note:

DHCP Server

in network

Operating system Recommended

method for:

UPnP™

See page 10

Optional Windows (ME or XP)

Bonjour

See page 11

Optional Mac OSX (10.4 or later) Macintosh

AXIS Dynamic DNS Service

See page 11

All

ARP/Ping

See page 12

All

View DHCP server

admin pages for IP address

(See note below)

Required All

To install the UPnP™ service on your computer, open the Control Panel from the Start Menu and select Add/Remove

Programs. Select Add/Remove Windows Components and open the Networking Services section. Click Details and then

select UPnP as the service to add.

Requirements

Installation methods

UPnP™ is a certification mark of the UPnP™ Implementers Corporation.

Andere Handbücher für Axis 216FD

Inhaltsverzeichnis

Sprachen:

Andere Axis Sicherheitskamera Handbücher

Axis

Axis F4005 Bedienungsanleitung

Axis

Axis Q6034-E Bedienungsanleitung

Axis

Axis P3905-R Mk II Bedienungsanleitung

Axis

Axis Q1604 Bedienungsanleitung

Axis

Axis P5534-E Bedienungsanleitung

Axis

Axis AXIS 212 PTZ Bedienungsanleitung

Axis

Axis AXIS 213 PTZ Bedienungsanleitung

Axis

Axis M5000-G Bedienungsanleitung

Axis

Axis DROP CEILING P5522-E Bedienungsanleitung

Axis

Axis Network Camera AXIS 221 Bedienungsanleitung

Axis

Axis P3214-V Bedienungsanleitung

Axis

Axis P1455-LE-3 Bedienungsanleitung

Axis

Axis S P13-E Bedienungsanleitung

Axis

Axis Q3505-V Bedienungsanleitung

Axis

Axis AXIS M1011 Bedienungsanleitung

Axis

Axis Q6044-C PTZ Bedienungsanleitung

Axis

Axis Q6000-E Mk II Bedienungsanleitung

Axis

Axis M5054 Bedienungsanleitung

Axis

Axis P5544 PTZ Bedienungsanleitung

Axis

Axis P3346 Bedienungsanleitung

Axis

Axis M5075-G Bedienungsanleitung

Axis

Axis Q3709-PVE Bedienungsanleitung

Axis

Axis Q6078-E Bedienungsanleitung

Axis

Axis Q1775 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung