Axis AXIS T95A00 Bedienungsanleitung
ENGLISH DEUTSCH ITALIANO ESPAÑOL
INSTALLATION GUIDE
FRAN
Ç
AIS
AXIS T95A00 Dome Housing
AXIS T95A10 Dome Housing
AXIS T95A00/T95A10 Dome Housing Page 3
ENGLISH
AXIS T95A00/T95A10 Dome Housing
The AXIS T95A00/T95A10 Dome Housing can be used in both indoor and outdoor camera
installations. Follow these instructions to complete the installation of the AXIS T95A00/T95A10
Dome Housing and Axis network camera.
Warning! High voltage - the electrical connection must be made by an authorized electrician.
Please observe relevant national and local regulations for the installation.
•“Package Contents” on page 4
•“Installation” on page 5
•“Technical Specifications” on page 16
Safety Rules
Only qualified technical personnel may install this device.
• Disconnect power before any technical work on the appliance.
• Do not use old or worn out power cables.
• Never make changes or connections that are not shown in this handbook; improper use of
the appliance may cause serious hazard and may damage the product.
• Use original spare parts. Non-original spare parts could cause fire, electrical discharge, or
other hazards.
• Before installing the device, check the supplied material to make sure it corresponds with
the order specification.
• Please retain this document for future reference.
Axis Network Cameras
The AXIS T95A00/T95A10 Dome Housing supports the following camera models:
Camera Model: Note:
• AXIS 213 PTZ Before you begin, make sure that the AXIS
T95A00/T95A10 Dome Housing package contents, and
the required cables, tools, and documentation are avail-
able. See “Package Contents” on page 4.
• AXIS 214 PTZ
• AXIS 215 PTZ
• AXIS 231D+/232D+
• AXIS 233D
Page 4 AXIS T95A00/T95A10 Dome Housing
Package Contents
Large box:
(1) AXIS T95A00/T95A10 Dome Housing
Small box:
(2) Domes - transparent and smoked
(1) Fastening ring for dome
(1) Rubber gasket for dome
(4) M3x10mm screws for fastening ring
Plastic bag:
(1) Plate for cable glands
(1) Gasket for the cable gland plate
(1) M20 cable gland
(1) M16 cable gland
(1) M12 cable gland
(1) Plastic nut for M20 cable gland
(1) Plastic nut for M16 cable gland
(1) Plastic nut for M12 cable gland
(3) M3x10mm screws
(3) M3x8mm screws
(4) M4x10mm screws
(3) M3 nuts
(4) M4 nuts
(4) Lock washers
(1) 3mm Allen key
Plastic bag:
(1) Desiccant salt bag
Additional parts:
(1) Power cable for AXIS 213 PTZ, AXIS 214 PTZ, and AXIS 215 PTZ
(1) Ethernet cable with 90 degree angle for AXIS 231D+/232D+
AXIS T95A00/T95A10 Dome Housing Page 5
ENGLISH
Tools/ Parts not included
Other required parts
Note:
Not all screws provided are required for all camera installations.
Installation
Follow these steps indoors before the installation outdoor to save time at the installation site.
Attach Universal Adaptor to camera
1. Remove the top cover of the housing (with four screws) from the housing using the 3mm allen
key.
2. For AXIS T95A00 Dome Housing only - remove the two connectors (with black and blue cables)
attached to the circuit board on top of the Universal Adapter.
3. Loosen the three screws holding the Universal Adaptor. Rotate slightly and remove the
Universal Adaptor from the housing.
4. Attach the Universal Adaptor to the camera. For details see page 14.
Note:
Do not install the camera in the housing at this point. Transport it carefully to the place of
installation first.
Phillips screw driver
Ceiling bracket for AXIS 231D+/232D+ (supplied with the network camera)
Adjustable wrench
Mounting bracket See www.axis.com for available brackets and accessories
Power cable Examples:
AWG20, 100-240 VAC cable (AXIS T95A00 Dome Housing)
AWG22, 24 VAC cable (AXIS T95A10 Dome Housing)
Network cable CAT 5 shielded twisted pair (STP) cable recommended
Soft cloth Recommended for protecting the dome while installing the housing
Top cover Black cable Blue cable
Universal Adaptor
Page 6 AXIS T95A00/T95A10 Dome Housing
Fix the dome cover to the housing
Place the fastening ring over the dome. Insert the four
10mm M3 screws, so you hold the ring, the dome
cover, and the gasket together. Fix the dome cover
(transparent or smoked) at the bottom of the housing.
AXIS 213 PTZ, AXIS 214 PTZ, and AXIS 215 PTZ power connection
Connect the (provided) power cable to the 12 VDC output as shown in the picture.
AXIS T95A00/T95A10 Dome Housing output 12V DC
Camera power cable Housing power connector
black
red
GND
12 V
fastening ring
Housing
Rubber gasket
Dome
Fastening ring
Network camera power cable
12V DC
brown cable
power connector
AXIS T95A00/T95A10 Dome Housing Page 7
ENGLISH
AXIS 231D+/232D+ and AXIS 233D power connection
1. Unplug the connector from the 12 VDC power supply opposite the bracket opening as shown in
the illustration below.
2. Remove the 2-pin green connector block from the cables.
3. Connect the cable to the camera’s power connector as described below:
AXIS 231D+/232D+
• AXIS T95A00 Dome Housing (24V DC)
• AXIS T95A10 Dome Housing (24V AC)
Connect the brown cable to the 24V AC/DC pins on the AXIS
231D+/232D+ connection module (see illustration).
Note:
The AXIS 231D+/232D+ connection module contains a
rectifier so the cables can be connected either way.
24V
~
+
~
-
12 VDC
power connector
Brown cable
remove green
connector
block
AXIS 231D+/232D+ Connection module
24V AC/DC
Page 8 AXIS T95A00/T95A10 Dome Housing
AXIS 233D
As the camera is not yet installed in the housing, this is a preparatory step
showing how to connect the brown cables from the 24V connector to the
8-pin green connector block (supplied with the camera). When the
camera is later installed in the housing, this connector block will then be
connected to the camera itself. Referring to the connection diagram on
the right, connect the brown cables for your version of the T95A.
• AXIS T95A00 Dome Housing (24V DC)
Connect +24V to AC/DC+
Connect -24V to GND/DC-
• AXIS T95A10 Dome Housing (24V AC)
Connect +24V to AC/DC+
Connect -24V to AC.
Prepare the cable gland plate
Fix the 3 cable glands to the cable gland plate and place the cable gland plugs on them. Insert the
four M3 screws through the gasket and plate.
The preparation for the network camera installation is now complete.
AXIS 233D
Connector
AC
AC/DC+
GND/DC-
12V out
GND
Line out
GND
Line/Mic in
AXIS T95A00/T95A10 Dome Housing Page 9
ENGLISH
Install the mounting bracket
Note:
Make sure all cables are in place but not powered, before you install the bracket. Keep
cables unpowered until the installation is complete.
1. Install the bracket for the AXIS T95A00/T95A10 Dome Housing on a wall and make sure that
the screws and plugs are appropriate for the wall (wood, metal, concrete, or any other), and
suitable for the weight of the housing. To install the bracket in the correct direction, see figure
below.
2. Pull a sufficient length of the cables through the bracket for the housing and camera
(approximately 50 cm).
Note:
Visit the Axis web site at www.axis.com for a comprehensive list of the available brackets
and accessories.
3170
182
150
81
230
14
140
110
77
9
14
Page 10 AXIS T95A00/T95A10 Dome Housing
Mount the housing to the bracket
Notes:
• Ensure that the bracket is securely fastened, and cables are pulled through it before mounting the
camera housing. Ensure that no power is connected to the cables.
• It is recommended that you place a soft, clean cloth (not included) into the dome to ensure it
remains clean until the time when you need to mount the camera.
1. If the top cover of the housing was attached to facilitate transportation, detach it again at this
point.
2. Position the AXIS T95A00/T95A10 Dome Housing against the bracket, making sure to pull the
cables (power, Ethernet, and I/O cables if applicable) into the housing, and tighten the two
25mm M5 allen key screws (included with the bracket).
3. Pull the cables through the cable glands, and secure the hole in the bracket with the cable
gland plate. Ensure the cables are securely fastened in the cable glands.
4. Remove the protective cloth (if you have used one) from the dome, and remove traces of dust.
Install the camera in the housing
1. Make sure power is disconnected from the housing before installing the camera.
2. Connect the network cable to the Ethernet port in the camera.
3. Connect the power cable to the camera.
4. If applicable, connect the I/O cables to the connectors as described in the installation guide
supplied with the camera.
5. Lower the Universal Adaptor with the attached camera into the AXIS T95A00/T95A10 Dome
Housing and tighten the 3 screws.
6. Connect power to the housing as described below.
•“For AXIS T95A00 Dome Housing” on page 11
•“For AXIS T95A10 Dome Housing” on page 12
Andere Handbücher für AXIS T95A00
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Axis Sicherheitskamera Handbücher
Axis
Axis M1033-W Bedienungsanleitung
Axis
Axis M3044-V Bedienungsanleitung
Axis
Axis P1427-LE Bedienungsanleitung
Axis
Axis Q3505-SVE Mk II Bedienungsanleitung
Axis
Axis M11-L Series Bedienungsanleitung
Axis
Axis M5526-E Bedienungsanleitung
Axis
Axis P4705-PLVE Bedienungsanleitung
Axis
Axis Q3505-VE Mk II Bedienungsanleitung
Axis
Axis AXIS P1405-LE Mk II Bedienungsanleitung
Axis
Axis 01054-001 Bedienungsanleitung
Axis
Axis M31-LVE Series Bedienungsanleitung
Axis
Axis P39 Series Bedienungsanleitung
Axis
Axis 02463-001 Bedienungsanleitung
Axis
Axis Q1932-E Bedienungsanleitung
Axis
Axis Q6032-E Bedienungsanleitung
Axis
Axis Q6032 Bedienungsanleitung
Axis
Axis M10 Series Bedienungsanleitung
Axis
Axis M1145 Bedienungsanleitung
Axis
Axis M3114-VE Nocap Bedienungsanleitung
Axis
Axis P1468-XLE Bedienungsanleitung
