Axis 247S Bedienungsanleitung

ENGLISH FRANCAIS DEUTSCH ESPAÑOL

ITALIANO

AXIS 247S Video Server

Installation Guide

AXIS 247S Installation Guide Page 3

ENGLISH

AXIS 247S

Installation Guide

This installation guide provides instructions for installing the AXIS 247S Video Server on

your network. For all other aspects of using the product, please see the User’s Manual,

available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Install the hardware. See page 4.

4. Set an IP address. See page 5.

5. Set the password. See page 8.

Package contents

Important!

• There are two alternative connections available for power out, video in and audio in, providing

flexible installation. Do not connect more than one video/audio source as the AXIS 247S is a

one-channel video server and can only accommodate one video/audio stream.

• The AXIS 247S can deliver a maximum of 5W (420mA) to a camera (from power out or Mini-

DIN connector) and 50mA from the I/O terminal connector.

Item Models/variants/notes

AXIS 247S Video Server

Terminal connector kit 4-pin and 2-pin connector blocks for connecting external devices

Mounting kit Metal plate and bracket for wall or cage mounting

CD AXIS Network Video Product CD, including product documentation, installation

tools and other software

Printed Materials AXIS 247S Installation Guide (this document)

Axis Warranty Document

Optional Accessory

Connector Cable Cable with 6 pin Mini-DIN connector for audio in, video in and power out

PoE Midspan Power over Ethernet midspan (1 port)

Important!

This product must be used in

compliance with local laws

and regulations.

Page 4 AXIS 247S Installation Guide

Hardware overview

Install the hardware

The Axis Video Server is supplied with a

mounting kit for wall or rack mounting. The

brackets can be positioned for mounting the

video server in a cage or on a vertical surface.

Follow the instructions below to attach the

brackets to the video server:

1. Slide the grey frame off the front panel of

the video server (no tools needed).

2. Insert the metal plates in the slots on each

side of the video server.

3. Depending on the intended installation

(rack or wall), position and attach the

brackets on each side, using the screws

provided.

4. Slide the grey frame back into position.

Video In

Power out

Video in

Audio in

Line/Mic

Power out

Network

(PoE)

Control

button I/O terminal

connector

Indicators for:

Network

Status

Power

75 Ohm switch

PoE

Class 2/

Class 3

Product ID & Serial number (S/N).

The serial number may be

required during the installation.

Product label includes:

Grey frame

Slot for metal

plate and bracket

metal plate

bracket

AXIS 247S Installation Guide Page 5

ENGLISH

Connect the cables

1. Connect the video server to the network using a shielded network cable. Power is also

supplied via the network cable (PoE).

2. Connect the video output of your camera to the AXIS 247S, using a standard 75 Ohm

coaxial video cable with BNC connectors.

3. Optionally connect external input/output devices, e.g. alarm devices. See page 10 for

information on the terminal connector pins.

4. Optionally connect a microphone or line in mono signal to the Line/Mic in connector.

5. Check that the indicator LEDs indicate the correct conditions. See the table on page 11

for further details.

Important!

• The 6 pin Mini-DIN connector is an alternative connection for power out, video in and audio in.

Do not connect more that one video source to the AXIS 247S.

• If PoE is not supported by the network switch, use a PoE midspan/power injector to connect

power to the AXIS 247S.

Assign an IP address

To make it accessible on the network, the AXIS 247S must be assigned an IP address.

Depending on the number of video servers you wish to install, the recommended method for

assigning IP addresses in Windows is either AXIS IP Utility or AXIS Camera Management.

Use the method that best suits your purpose.

Both of these free applications are available on the Axis Network Video Product CD supplied

with this product, or they can be downloaded from www.axis.com/techsup

Notes:

•AnetworkDHCPserver is optional.

• The AXIS 247S has the default IP address 192.168.0.90

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address of the AXIS 247S, e.g. in other

operating systems, see page 9.

Method Recommended for Operating system

AXIS IP Utility

See page 6

Single video server

Small installations

Windows

AXIS Camera Management

See page 7

Multiple video servers

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Page 6 AXIS 247S Installation Guide

AXIS IP Utility - single video server/small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. The

application can also be used to manually assign a static IP address.

Note that the computer running AXIS IP Utility must be on the same network segment

(physical subnet) as the AXIS 247S.

Automatic discovery

1. Check that the AXIS 247S is connected to the network and that power has been applied.

2. Start AXIS IP Utility.

3. When the video server appears in the window, double-click it to open its home page.

4. See page 8 for instructions on how to assign the password.

Assign the IP address manually

1. Acquire an unused IP address on the same network segment as your computer.

2. Click the button Assign new IP address using serial number and enter the serial

number and IP address for the AXIS 247S. The serial number is located on the product

label.

3. Click the Assign button and follow the instructions.

4. Click the Home Page button to access the video server’s web pages.

5. See page 8 for instructions on how to set the password.

AXIS 247S Installation Guide Page 7

ENGLISH

AXIS Camera Management - multiple servers/large installations

AXIS Camera Management can automatically find and set IP addresses, show connection

status, and manage firmware upgrades for multiple Axis video products.

Automatic discovery

1. Check that the video server is connected to the network and that power is applied.

2. Start AXIS Camera Management. When the AXIS 247S appears in the window, double-

click it to open the video server’s home page.

3. See page 8 for instructions on how to set the password.

Set the IP address in multiple devices

AXIS Camera Management speeds up the process of assigning IP addresses to multiple

devices, by suggesting IP addresses from a specified range.

1. Select the devices you wish to configure (different models can be selected) and click the

Assign IP button.

2. Select Obtain IP addresses automatically (DHCP), click the Update button and the

program will search in the specified range and suggest an IP address for each device.

-or-

Enter the range of IP addresses, the subnet mask and default router that devices can use

and click the Update button.

Page 8 AXIS 247S Installation Guide

Set the password

When accessing the AXIS 247S for the first

time, the ‘Configure Root Password’ dialog

will be displayed.

1. Enter a password and then re-enter it, to

confirm the spelling. Click OK.

2. Enter the user name root in the dialog.

Note: The default administrator user name

root cannot be deleted.

3. Enter the password as set above, and click OK. If the password is lost, the AXIS 247S

must be reset to the factory default settings. See page 12.

4. If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the

video stream in Internet Explorer. You will need administrator rights on the computer to

do this.

The Live View page of the AXIS 247S is displayed, with links to the Setup tools, where the

configuration is done.

Setup - Provides all the tools for configuring

the video server to requirements.

Help - Displays

online help on all

aspects of using

the video server.

AXIS 247S Installation Guide Page 9

ENGLISH

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address.

All methods are enabled by default, and all can be disabled.

Set the IP address with ARP/Ping

1. Acquire an IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the AXIS 247S label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the video server and then start/restart the

AXIS 247S, by disconnecting and reconnecting power.

5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter

on your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd.

Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Use in operating

system

Notes

UPnP™

Windows

(ME or XP)

When enabled on your computer, the video server is

automatically detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the video server’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your video server. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the video server.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address> arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address> arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

Page 10 AXIS 247S Installation Guide

Unit connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using

shielded cables is recommended.

I/O terminal connector - Used in applications for e.g. motion detection,

event triggering, time lapse recording and alarm notifications:

• 1 transistor output - For connecting external devices such as relays and LEDs.

Connected devices can be activated by AXIS VAPIX API, output buttons on the

Live View page or by an Event Type. The output will show as active (shown

under Event Configuration > Port Status) if the alarm device is activated.

• 1 digital input - An alarm input for connecting devices that can toggle between an open and

closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a

signal is received the state changes and the input becomes active (shown under Event

Configuration > Port Status).

BNC connector - Connect a 75 ohm coaxial video cable (max. length 800 feet (250 meters).

Mini-DIN - 6 pin Mini-DIN connector for power out, video in and audio in:

Line/Mic in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is

used from a stereo signal).

Power out - Used to power a camera or other auxiliary equipment 12V DC,

max. load 5W (420mA)

Function Pin I/O Terminal Connector Pin Description Specifications

GND 1

Power 2 Can be used to power auxiliary equipment. 12V DC

Max load = 50mA

Digital

Input

3 Connect to GND to activate, or leave floating (or

unconnected) to deactivate.

Must not be exposed to

voltages greater than 10V DC

Transistor

Output

4 Uses an open-collector NPN transistor with the

emitter connected to the GND pin. If used with an

external relay, a diode must be connected in parallel

with the load, for protection against voltage

transients.

Max load = 50mA

Max voltage = 24V DC

(to the transistor)

Function Pin Mini-DIN Pin Description Mini-DIN Connector

Power out 1 12V DC, max. load 5W (420mA)

Audio in 3 Mono microphone or a line-in

Video in 5 Composite video (Not S-video or Y/C video)

GND 2,4,6 Ground on pins 2, 4 and 6.

Pins

234

GND +

Andere Handbücher für 247S

Inhaltsverzeichnis

Sprachen:

Andere Axis Server Handbücher

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis 7000 Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis 2400 - PHP3 GUIDE Bedienungsanleitung

Axis

Axis 240Q Blade Bedienungsanleitung

Axis

Axis AXIS 243Q Blade Bedienungsanleitung

Axis

Axis 7100 Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis 2400AM Bedienungsanleitung

Axis

Axis 243SA Bedienungsanleitung

Axis

Axis 950 Bedienungsanleitung

Axis

Axis Video Server 242S IV Bedienungsanleitung

Axis

Axis 2400 Bedienungsanleitung

Axis

Axis Camera Station S12 Series Bedienungsanleitung

Axis

Axis S2108 Bedienungsanleitung

Axis

Axis E100 Bedienungsanleitung

Axis

Axis 2400+ Bedienungsanleitung

Axis

Axis Camera Station S1216 Tower Bedienungsanleitung

Axis

Axis Camera Station S1216 Tower Bedienungsanleitung

Axis

Axis exacqVision Edge Bedienungsanleitung

Axis

Axis 7000 FX Bedienungsanleitung

Axis

Axis 250S Blade Bedienungsanleitung

Axis

Axis 70 Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung