Axis 291 1U Bedienungsanleitung

ENGLISH DEUTSCH ITALIANO ESPAÑOL

INSTALLATION GUIDE

FRAN

AIS

吤雬

AXIS 291 1U Video Server Rack

AXIS Video Server Rack Installation Guide Page 3

ENGLISH

Axis Rack Mounted Video Server Solution

This installation guide describes the hardware installation of the AXIS 291 1U Video Server Rack,

which can hold up to 3 Axis blade video servers. To install the Axis video server on the network,

please see the video server’s own installation guide.

Hardware Inventory

Please contact your dealer if anything is missing or damaged.

Power cord plug variants

Mounting kit

Please contact your dealer if anything is missing or damaged.

Qty Item Models/variants/notes

1 Video server rack AXIS 291 1U Video Server Rack

2 Cover plates Front panel cover 1U

1 AC power cord • Europe

•UK

• US, Canada, Japan

• Australia

•Switzerland

•Denmark

•Southkorea

1 Warranty Document

1 Mounting kit See separate inventory below

Country Europe UK US,

Canada,

Japan

Australia Switzerland Denmark South

Korea

Power

cord plug

Qty Item Models/variants/notes

4 Rubber foot For placement on flat surfaces

1 Mounting bracket (side) Left

1 Mounting bracket (side) Right

8 M3x8 screw (recessed) For attachment of side brackets

4 M6x20 screw For mounting AXIS Video Server

Rack in equipment rack

3 Terminal connector

block

12-pin, green

The 2 mounting brackets included

in the mounting kit are slightly

different. See the label on each

bracket.

Note:

Page 4 AXIS Video Server Rack Installation Guide

AXIS 291 1U Video Server Rack - Overview

Read the following information to familiarize yourself with the AXIS 291 1U Video Server Rack,

making note of where the connectors and indicators are located.

Power Connector - Input power: 100-240V AC, 50-60 Hz, 1.9A

I/O Terminal Connector(s) - provides the physical interface to the functions supported by the Axis

blade video server. For more information see page 8.

Power & Network LEDs - The 10/100 LED flashes red for 10 Mbit, and flashes green for 100 Mbit.

The 1000 LED flashes green for 1 Gbit. The power LED shows steady green when the rack is

powered.

Network Connector - Axis blade video servers are designed for 10/100/1000 Mbps networks and

are connected via a standard RJ-45 connector.

Placement requirements

The location the AXIS 291 1U Video Server Rack is used in must meet the following requirements:

• Ambient temperature: 0° to +45°C (32° to 113°F)

• Relative humidity: 20-80%

• Power source within 1.8 meters

• Minimum 5cm free space on each side, to ensure adequate ventilation

• No excessive dust

Placement on a shelf/table

1. Attach the 4 rubber feet to the underside of the

unit, as illustrated here.

2. Place on a flat surface. Note that the AXIS Video

Server Rack with cables weighs up to 6kg. Check

that the surface can support this weight.

Power

Connector

Power & Network

LEDs

I/O Terminal

Connector 3 Network

Connector

I/O Terminal

Connector 2

I/O Terminal

Connector 1

AXIS Video Server Rack Installation Guide Page 5

ENGLISH

Installation in a 19” equipment rack

Requirements

• Pozidriv screwdriver #1

• Pozidriv screwdriver #3

• The rack must be braced and bolted to the floor.

• The AXIS Video Server Rack must be grounded to the same ground as the equipment

rack.

When mounting the AXIS Video Server Rack in a rack, never stack other units directly on top - the

mounting brackets are not designed to support more than 1 unit. Each unit in the rack must be

secured with appropriate brackets. Place the heaviest units at the bottom of the rack.

Attaching the brackets

The 2 mounting brackets are slightly different. To tell these apart, see the label on each bracket. See

also the illustration on page 3.

1. Remove the screw shown here from

each side of the unit. These will be

replaced by the screws used to fasten

the bracket.

2. Using the recessed M3X8 screws,

fasten the bracket to the side of

the unit. Do not use the screw that

was removed in step 1.

3. Slide the AXIS Video Server Rack

into the equipment rack. Insert the

M6X20 screws and tighten.

Page 6 AXIS Video Server Rack Installation Guide

Connect power

The AXIS Video Server Rack has no On/Off switch or button and will power up as soon as the power

cord is connected. Detaching the cord is the only way to remove power, so it is important to locate

the unit so that the power cord is easily accessible. Please ensure that the correct AC power cord for

your country is used.

Note also the following requirements and restrictions:

• To prevent the risk of electrical shock when in contact with the unit casing, only earthed/

grounded power cords should be used to power the AXIS Video Server Rack.

• Protection against overcurrents, short circuits and earth faults should be provided in the build-

ing installation.

• The AXIS Video Server Rack is intended for indoor use only, and only for TN and IT power sys-

tems.

• The AXIS 291 Video Server Rack is designed for use with Axis Blade Video Servers only.

• If a foreign object is accidently dropped into the Video Server Rack, always disconnect power

before attempting to remove the object.

Power specifications

• Input voltage 100-240V AC, at 50/60Hz

• Input current: 1.9A

• Power consumption with 3 x AXIS 243Q: Max 80W

AXIS Video Server Rack Installation Guide Page 7

ENGLISH

AXIS blade video servers

S/N - (serial number) is identical to the unit’s MAC/Ethernet address,

e.g. 00408C1A2B3C = 00-40-8C-1A-2B-3C.

P/N - is the product’s model number.

Bus Connector - This is the physical interface to the I/O terminal connector on the rack.

DIP Switches (4-port models) - Each video input has a corresponding line termination DIP switch.

Axis blade video servers are supplied with the line termination enabled for each input; i.e. with the

DIP switches set to ON (down position). To connect the video server in parallel with other

equipment, disable the input termination by setting the corresponding DIP switch to OFF (up

position). Failure to do so may affect the image quality negatively.

DIP Switches (1-port models) - These models can accommodate either composite or Y/C video.

The type to use is determined by the DIP switch settings. 1-port AXIS blade video servers are

supplied configured for composite video input, as shown in the table below.

Switch 1 2 3 4

Description 75 ohm video in

termination

75 ohm video out

termination

Connects video in

and video out

Not used

Composite video

input

on off on n/a

Y/C video input on on off n/a

Bus

Connector

DIP Switches

S/N & P/N label

4 Video inputs

Page 8 AXIS Video Server Rack Installation Guide

Mounting AXIS blade video servers

The AXIS Video Server Rack can accommodate 3 Axis blade video servers. The slots for these are

numbered 1-3 from left to right, as seen from the front. The I/O connectors for each slot on the rear

panel are also numbered.

1. Remove a front panel cover from the slot in which the video server will be mounted. This is

done by unfastening the screw on each side of the cover.

2. Slide the video server into place, using the guides as an aid. The dip switch for setting the line

termination should be visible on the top edge.

3. Fix the video server in place, using the screws from the front panel cover.

Note: Leaving an empty slot on the AXIS Video Server Rack open is not permitted. Front panel covers must

be used on all empty slots.

The I/O Terminal connector

The AXIS Video Server Rack server provides an I/O terminal connector for each Axis blade video

server (see illustration on page 4). This is used for connecting external equipment, in applications

for e.g. motion detection, event triggering, time lapse recording, alarm notification via email, image

storage to FTP locations, etc.

AXIS Video Server Rack Installation Guide Page 9

ENGLISH

Connector interfaces

The interfaces available via the 12-pin I/O terminal connector are as follows:

•4 Digital inputs - used for e.g. a pushbutton. If the button is pressed, the state changes

and the input will be active (shown under Event Configuration > Port Status). (AXIS

241Q Blade, AXIS 241S Blade, AXIS 243Q, AXIS 240Q)

•4 Transistor outputs - for e.g. alarm devices that can be activated from Output buttons

on the Live View page, or as an action to an Event Type. The output will show as active

(in Event Configuration > Port Status) if the device is activated.

• 10 configurable I/O connectors (AXIS Q7406)

•RS-485 interface, for e.g. Pan/Tilt/Zoom devices (see www.axis.com for drivers)

• Auxiliary power

Connector pinout

To connect input/output devices to the I/O terminal connector:

1. Referring to the table above, loosen the corresponding screw on top of the pin on the green

connector block.

2. Push the cable into the connector block and secure it by fastening the screw.

3. Once all devices are connected, push the connector block into the terminal connector on the

rear panel of the AXIS Video Server Rack.

For compatible replacement connectors, contact http://www.phoenixcontact.com, quoting: MC1.5/

12-ST-3.81 (art no 1803675).

Pin AXIS Q7406 AXIS 243Q AXIS 241Q Blade,

AXIS 241S Blade, AXIS 240Q

1 +12V out, 100mA +12V out, 100mA +12V out, 100mA

2 GND GND GND

3 Channel 1, Configurable I/O 1 Channel 1, Input 1 Input1

4 Channel 2, Configurable I/O 1 Channel 2, Input 1 Input 2

5 Channel 3, Configurable I/O 1 Channel 3, Input 1 Input 3

6 Channel 4, Configurable I/O 1 Channel 4, Input 1 Input 4

7 Channel 5, Configurable I/O 1 Channel 1, Input 1 Output1

8 Channel 6, Configurable I/O 2 Channel 2, Input 1 Output2

9 Channel 1, Configurable I/O 2 Channel 3, Input 1 Output3

10 Channel 2, Configurable I/O 2 Channel 4, Input 1 Output4

11 Channel 1, RS485A Channel 1, RS485A RS485A

12 Channel 1, RS485B Channel 1, RS485B RS485B

AXIS 291 1U Installation Guide v2.3 June 2009

POWERPOWER

Assembly of multi-channel video server

Serial numbers for each blade video server affixed here

Andere Handbücher für 291 1U

Inhaltsverzeichnis

Andere Axis Server Handbücher

Axis

Axis 70 Bedienungsanleitung

Axis

Axis 7000 Benutzerhandbuch

Axis

Axis Video Server 242S IV Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis AXIS 240 Bedienungsanleitung

Axis

Axis 950 Bedienungsanleitung

Axis

Axis AXIS 243Q Blade Bedienungsanleitung

Axis

Axis StorPoint NAS 100 Bedienungsanleitung

Axis

Axis 250S Blade Bedienungsanleitung

Axis

Axis 7000 FX Bedienungsanleitung

Axis

Axis exacqVision Edge Bedienungsanleitung

Axis

Axis Camera Station S12 Series Bedienungsanleitung

Axis

Axis Video Server 242S IV Bedienungsanleitung

Axis

Axis 5600+ Bedienungsanleitung

Axis

Axis 7000 Bedienungsanleitung

Axis

Axis AXIS 243Q Blade Bedienungsanleitung

Axis

Axis AXIS StorPoint CD Bedienungsanleitung

Axis

Axis 2400+ Bedienungsanleitung

Axis

Axis E100 Bedienungsanleitung

Axis

Axis 291 1U Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis Camera Station S1216 Tower Bedienungsanleitung

Axis

Axis AXIS 241QA Bedienungsanleitung

Axis

Axis Video Server Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung