Axis AXIS 243Q Blade Bedienungsanleitung

ENGLISH FRANCAIS DEUTSCH ESPAÑOL

ITALIANO

AXIS 243Q

Blade Video Server

Installation Guide

AXIS 243Q Blade Installation Guide Page 3

ENGLISH

AXIS 243Q Blade

Installation Guide

This installation guide provides instructions for installing the AXIS 243Q Blade Video Server

on your network. For all other aspects of using the product, please see the User’s Manual,

available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Assign an IP address. See page 6.

4. Set the password. See page 7.

Package contents

Please contact your dealer if anything is missing or damaged.

Item Models/variants/notes

Video server AXIS 243Q Blade

CD AXIS Network Video Product CD, including product documentation, installa-

tion tools and other software

Printed Materials AXIS 243Q Blade Installation Guide (this document)

Axis Warranty Document

Extra serial number label

Important!

• To mount the hardware in the AXIS 291 1U Video Server Rack, please see the

Installation Guide for the server rack

• This product must be used in compliance with local laws and regulations.

Page 4 AXIS 243Q Blade Installation Guide

Hardware overview

AXIS 243Q Blade Video

Server

DIP Switches - Each video

input has a corresponding line

termination DIP switch. Axis

blade video servers are supplied

with the line termination

enabled for each input; that is,

with the DIP switches set to ON

(down position).

To connect the video input in

parallel with other equipment,

disable the input termination

by setting the corresponding

DIP switch to OFF (Up posi-

tion). Failure to do so may

affect the image quality nega-

tively.

Bus Connector - This is the

physical interface to the video

server rack, providing power,

network and the I/O terminal

connector.

Control Button - This button is

used to reset the video server to

the factory default settings. See

page 9.

Video Inputs - The AXIS 243Q

Blade supports 4 video sources

(VIDEO 1 - VIDEO 4). Each

video input is terminated using

a coax/BNC connector.

Physical connections made

using 75 Ohm coaxial video

cable have a recommended

maximum length of 800 feet

(250 meters).

Bus

Connector

DIP Switches

Control button

LED Indicators

Video inputs 1-4

Serial number

label

AXIS 243Q Blade Installation Guide Page 5

ENGLISH

LED Indicators

AXIS 291 1U Video Server Rack

Power Connector - Input power: 100-240V AC, 50-60 Hz, 1.9A

I/O Terminal Connector(s) - provides the physical interface to 1 output and 1 input for each

video input. Video input 1 on each blade also provides an RS-485 interface, usually used for

connecting Pan Tilt Zoom devices.

Power & Network LEDs - The 10/100 LED flashes red for 10 Mbps, and flashes green for 100

Mbps. The 1000 LED flashes green for 1 Gbps. The power LED shows steady green when the

rack has power.

Network Connector - Axis blade video servers are designed for 10/100/1000 Mbps networks

and connect via the standard RJ-45 connector.

Network Green Steady green - no network activity

Flashes green - network activity

Status Green Steady green - normal operation

Red One flash - one or more units starting up

Two flashes - a unit is resetting to factory default settings

Steady red - hardware error on one or more units

Green/red Flashes for no connection to AXIS Internet Dynamic DNS Service

Power Green Normal operation

Green/Amber Flashes for unit upgrade

I/O Terminal

Connector 1

Power

Connector

Power &

Network LEDs

I/O Terminal

Connector 2

I/O Terminal

Connector 3

Network

Connector

Page 6 AXIS 243Q Blade Installation Guide

Assign an IP address

To make it accessible on the network, the AXIS 243Q Blade must be assigned four IP

addresses, one for each video input.

AXIS Camera Management

AXIS Camera Management can automatically find and assign IP addresses, show connection

status, and manage firmware upgrades for multiple Axis video products.

Automatic assignment of IP addresses

AXIS Camera Management speeds up the process of assigning IP addresses to multiple

devices, by suggesting IP addresses from a specified range.

1. Check that the AXIS 243Q Blade is connected to the network and that power has been

applied.

2. Start AXIS Camera Management. The AXIS 243Q Blade appears in the window, with one

entry for each video input. These are shown as AXIS 243Q(1) Blade, AXIS 243Q(2) Blade,

AXIS 243Q(3) Blade, and AXIS 243Q(4) Blade. Double-click an entry to open the home

page for that video input.

3. See page 7 for instructions on how to set the password.

Changing IP addresses

1. To change IP addresses, select the devices you wish to configure and click the Assign IP

button.

2. Select Obtain IP addresses automatically (DHCP), click the Update button and the

program will search in the specified range and suggest an IP address for each device.

-or-

Enter the range of IP addresses, the subnet mask and default router that devices can use

and click the Update button.

AXIS 243Q Blade Installation Guide Page 7

ENGLISH

Set the password

When accessing the AXIS 243Q Blade for the

first time, the ‘Configure Root Password’

dialog will be displayed.

1. Enter a password and then re-enter it, to

confirm the spelling. Click OK.

2. Enter the user name root in the ‘Enter

Network Password’ dialog.

Note: The default administrator user name root cannot be deleted.

3. Enter the password as set above, and click OK. If the password is lost, the AXIS 243Q

Blade must be reset to the factory default settings. See page 9.

4. If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the

video stream in Internet Explorer. You will need administrator rights on the computer to

do this.

The Live View page of the AXIS 243Q Blade is displayed, with links to the Setup tools, which

allow you to customize the video server.

AXIS 243Q Blade User’s Manual

For more information on how to use and configure the video server on your network, please

refer to the AXIS 243Q Blade User’s Manual, available on the CD supplied with this product,

or from the Axis Web site at www.axis.com

Page 8 AXIS 243Q Blade Installation Guide

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering IP addresses.

All methods are enabled by default, and all can be disabled.

Set the IP address with ARP/Ping

1. Acquire 4 IP addresses on the same network segment your computer is connected to.

2. Locate the 4 serial numbers (S/N) on the included label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected and then start/restart the video server, by

disconnecting and reconnecting power.

5. When you see ‘Reply from 192.168.0.125: ...’ or similar, press Ctrl+C.

6. Repeat steps 3, 4 and 5 for the remaining video inputs.

7. In your browser, type in http://<IP address> in the Location/Address field and press Enter

on your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Use in operating

system

Notes

UPnP™

Windows When enabled on your computer, the video server is automati-

cally detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the video server’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your video server. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the video server.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Windows syntax Windows example

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address> arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax UNIX/Linux/Mac example

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address> arp -s 192.168.0.125 00:40:8c:18:10:00

temp

ping -s 408 192.168.0.125

AXIS 243Q Blade Installation Guide Page 9

ENGLISH

Resetting to the Factory Default Settings

This will reset all the parameters in all 4 units (including all four IP addresses) to the factory

default settings.

1. Disconnect power.

2. Press and hold the Control button and reconnect power.

3. Release the button when the

Status Indicator displays red

(which may take up to 15

seconds). When the Status

Indicator changes to Green

(which may take up to 1

minute), the process is

complete and the unit 4 has

been reset.

4. Re-assign the IP addresses,

using one of the methods

described in this document.

To reset an individual unit to the original factory default settings, use the button provided in

that unit’s web interface. For more information, please see the online help.

Further information

The user’s manual is available from the Axis Web site at www.axis.com or from the Axis

Network Video Product CD supplied with this product.

Control button

LED Indicators

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your

AXIS 243Q Blade. To see the currently installed firmware version, see the Basic

Configuration web page in the product’s Setup tools.

Andere Handbücher für AXIS 243Q Blade

Inhaltsverzeichnis

Sprachen:

Andere Axis Server Handbücher

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis exacqVision Edge Bedienungsanleitung

Axis

Axis NETEYE 200 Bedienungsanleitung

Axis

Axis 291 1U Bedienungsanleitung

Axis

Axis FA54 Bedienungsanleitung

Axis

Axis 247S Bedienungsanleitung

Axis

Axis 2400+ Bedienungsanleitung

Axis

Axis 70 Bedienungsanleitung

Axis

Axis S2016 Bedienungsanleitung

Axis

Axis 2400AM Bedienungsanleitung

Axis

Axis 247S Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis Video Server 242S IV Bedienungsanleitung

Axis

Axis 250S MPEG-2 Bedienungsanleitung

Axis

Axis 282 Bedienungsanleitung

Axis

Axis 250S Blade Bedienungsanleitung

Axis

Axis AXIS 241QA Bedienungsanleitung

Axis

Axis 7000 Service-Handbuch

Axis

Axis 7100 Bedienungsanleitung

Axis

Axis 2490 Bedienungsanleitung

Axis

Axis 7100 Bedienungsanleitung

Axis

Axis AXIS 240 Bedienungsanleitung

Axis

Axis E100 Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung