Axis 282 Bedienungsanleitung

AXIS 282/282A

Bare Board Video Server

Installation Guide

AXIS 282/282A Installation Guide Page 1

AXIS 282/282A

Bare Board Video Server

Installation Guide

This installation guide is applicable for the following Axis Video Servers:

•AXIS 282: 1-port bare board video server

•AXIS 282A: 1-port bare board video server

including 2-way audio

For a complete description, get the AXIS 282/282A Bare Board Video

Server User’s Manual online from Axis Web site, www.axis.com

The AXIS 282/282A is a small form factor video server board designed to

be built into domes, fixed view cameras, PTZs, analog devices, etc., and is

fully featured for security surveillance and remote monitoring needs. The

AXIS 282 is based on the AXIS ETRAX 100LX network optimized system-

on-a-chip (SOC), and the AXIS ARTPEC-2 compression chip.

The AXIS 282/282A is equipped with RS-232 or RS-485 ports for

connecting third party PTZ systems. It also has 1 alarm input and 1 alarm

output, which can be used to connect various third party devices, for

example door sensors and alarm bells.

The AXIS 282A has a Line/Mic In (mono), via the internal connector I/O

pins, for connecting an external microphone or other source producing a

line level signal. An active speaker with a built-in amplifier can be

connected to Line Out (mono) to enable two-way communication. Audio

communication can be bi-directional (full-duplex), push to talk (half-

duplex) or in one direction only (simplex).

Page 2 AXIS 282/282A Installation Guide

AXIS 282/282A Top

Not included:

•4 M2 screws - needed for mounting AXIS 282/282A

•34 pin IDC female connector (2mm)

34-pin header

Mounting holes

Mounting hole

Terminal I/O

connector

Network

connector

AXIS 282/282A Installation Guide Page 3

The Terminal I/O Connector

The AXIS 282/282A provides one 4-pin terminal I/O connector.

Note: Pins 3 and 4 in the Terminal I/O Connector are the same Alarm In and Alarm Out as pins 8 and 9 in

the 34-Pin Header.

If the AXIS 282/282A has been configured to have power going in

through the 34 I/O pins, power can be configured to go out through pin 1

of the Terminal I/O Connector.

Schematic Diagram - Terminal I/O Connector

Network connector

The AXIS 282/282A connects to the network via a standard STP network

cable, and automatically detects the speed of the local network segment

(Ethernet 10BaseT/100BaseTX, RJ-45).

Pin Function

1 Power in/out (8 - 20V)

2GND

3AlarmIn

4AlarmOut

123 4

Page 4 AXIS 282/282A Installation Guide

The 34-Pin Header

The AXIS 282/282A has a 34-Pin Header to be used with a 2mm IDC connector.

Connections include:

•Serial port, configurable as RS-232 or RS-485, which is typically used for con-

necting Pan/Tilt/Zoom devices.

•Video in and out connections

•Audio in and out connections

•LED outputs

•DC power auxiliary connection point

Pin Function Pin Function

1 Network LED green 2 Network LED red

3 Status LED green 4 Status LED red

5 Flash LED 6 Power LED

7 Control button 8 Alarm In

9 Alarm Out 10 Ground

11 Y/C Video in (Y) 12 Y/C GND

13 Y/C Video in (C) 14 Y/C GND

15 Composite Video In 16 Composite Video Source

GND

17 •AXIS 282: Not used

•AXIS 282A MIC/Line in

18 Mic/Line in GND

19 •AXIS 282: Not used

•AXIS 282A Audio/Line out

20 Line Out GND

21 RS-485 B 22 RS-485 A

23 Serial port RTS (RS-232) 24 Serial port CTS (RS-232)

25 Serial port TXD (RS-232) 26 Serial port RXD (RS-232)

27 Serial port GND 28 Power GND

29 Power GND 30 Power I/O

31 Power GND 32 Power IN

33 Power IN 34 Power IN

AXIS 282/282A Installation Guide Page 5

Schematic Diagram - 34 I/O Pins

Note: Pins 8 and 9 in the 34-Pin Connector

are the same Alarm In and Alarm Out

as pins 3 and 4 in the Terminal I/O Connector.

Page 6 AXIS 282/282A Installation Guide

AXIS 282/282A Bottom

LED indicators - See AXIS 282/282A User’s Manual for a complete

listing of the status of the colored Status, Network, and Power

indicators.

Control button - Used to restore the factory default settings, as

described in AXIS 282/282A User’s Manual.

Flash button - The AXIS 282/282A has a flash button. Used only for

firmware programming in the factory and not when upgrading the

firmware! See AXIS 282/282A User’s Manual for more information.

Status LED

Network LED

Power LED

Control button

Flash button

AXIS 282/282A Installation Guide Page 7

Integration of the AXIS 282/282A

Mechanical integration may be done through the 4 mounting holes on the

AXIS 282/282A, shown in the figure below. Electrical integration of the

AXIS 282/282A is done through the connectors described here.

Mounting holes

19mm

Network Connector Control button Flash button

Page 8 AXIS 282/282A Installation Guide

Technical Specifications

For a complete detailed description of technical specifications see the AXIS

282/282A Bare Board Video Server User’s Manual.

Item Specification

Models • AXIS AXIS 282: 1-channel bare board video server

• AXIS AXIS 282A: 1-channel bare board video server with two-way audio

Audio features

AXIS 282A only

• G.711 PCM 64kbit/s, G.726 ADPCM 32 or 24 kbit/s, full duplex, half

duplex, simplex or audio off

Connectors • One 34-pin I/O header

- 1 analog composite or Y/C video input (NTSC/PAL autosensing )

- RS-485 or RS-232 port

- 1 alarm input, 1 alarm output

- Power connection (input and output)

- LED outputs

- Audio input (282A): Microphone (54 mVpp) or Line in (8.0 Vpp),

mono

- Audio output (282A): Line out (2.6 Vpp), mono

• Terminal block:

- 1 alarm input, 1 alarm output

- Alternative power connection

• Ethernet 10Base/100BaseTX,RJ-45 connector

Power • Via pin 3 of the Terminal Block: 8 - 20V DC, max 8W

• Via pins 32 - 34 of the 34-pin header: 8 -20V DC, max 8W

Operating

conditions

• Temperature: 5oC (41oF) to 50oC (122oF)

• Humidity: 20-80% RH (non-condensing)

Installation,

management

and

maintenance

User’s manual and installation tool available at www.axis.com

Web-based configuration, Configuration backup and restore Firmware

upgrades over HTTP or FTP, firmware available at www.axis.com

Approvals • AXIS 282/AXIS 282A is delivered as a component for the sole purpose of

being integrated into a product or system. The foregoing implies an

obligation on behalf of the integrator to obtain any approvals from

authorities or governmental bodies that may be required for the lawful

use of the finished product or system, which includes the

AXIS 282/AXIS 282A as a component. Resale and use of the AXIS 282/

AXIS 282A on a stand-alone basis is not allowed.

Dimensions • HxWxD = 19 x 79 x 82mm (3/4” x 3 1/8” x 3 1/4”)

• Weight: 60g (2 1/8oz)

Andere Handbücher für 282

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Axis Server Handbücher

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis 282 Bedienungsanleitung

Axis

Axis 282 Bedienungsanleitung

Axis

Axis Developer Board and Device Server AXIS 82+ Bedienungsanleitung

Axis

Axis Camera Station S1216 Tower Bedienungsanleitung

Axis

Axis AXIS 240 Bedienungsanleitung

Axis

Axis 2400+ Bedienungsanleitung

Axis

Axis 2400 Bedienungsanleitung

Axis

Axis Camera Station S1116 Racked Recorder Bedienungsanleitung

Axis

Axis exacqVision Edge Bedienungsanleitung

Axis

Axis 700 Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis Q7900 Rack Bedienungsanleitung

Axis

Axis AXIS 243Q Blade Bedienungsanleitung

Axis

Axis Video Server AXIS 241SA Bedienungsanleitung

Axis

Axis 2400+ Bedienungsanleitung

Axis

Axis Camera Station S1264 Rack Bedienungsanleitung

Axis

Axis 7100 Bedienungsanleitung

Axis

Axis 7000 Bedienungsanleitung

Axis

Axis 241Q Blade Bedienungsanleitung

Axis

Axis 240Q Blade Bedienungsanleitung

Axis

Axis 2490 Bedienungsanleitung

Axis

Axis 250S Blade Bedienungsanleitung

Axis

Axis 70 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung