B-TEK Scales Above-ground Bedienungsanleitung

Instruction

Manual

Wheelchair

Patient Scales

7/23

Rev. V2023.0

Table of Contents

1. Safety First…………………………………………………………………………….…….. 3

2. Introduction/Specifications.……………………………………………………………..…. 4

3. General Component Identification ………………………………………………….……. 5

4. Installation Above Ground………………………………………………………………...6,7

5. Installation In-ground…………………….…………………………………………..…….8,9

6. Indicator Termination, Calibration………………………………….……………………..10

7. Replacement Parts…...…...………………………………………………………………..11

8. BTEK Contact Information…………………………………………………………………12

Safety First

•Please call a B-TEK authorized service provider for service or repairs

on B-TEK products.

•Only allow authorized personnel to work with electrical components.

•Please ensure you wear proper PPE when working with equipment.

•Ensure proper training is given when working with any equipment.

•Ensure that the area used for this equipment is safe for this equipment.

•Allow only qualified personnel to work on electric/electronic components.

•Do not use this equipment for anything other than its intended use.

•Ensure equipment is plugged into stable power sources.

•Keep equipment away from high voltage, vibration, and high draft areas.

•Keep equipment cords and cables secured and protected.

•Perform periodic inspections to keep equipment in good working order.

•Never apply a load over the capacity of your scale.

•Keep the area around your scale free of debris.

SAFETY WARNING

Always unplug or remove power source if equipment may encounter water such

as rain or area flooding.

Never power equipment back up until the area and equipment are 100%

confirmed dry and free of any water or moisture.

Introduction

The information provided in this manual is a guide to installing the B-TEK, LLC. Patient series

floor scales. This document is intended as a guide only, and the actual installation should be

performed by qualified personnel.

All sales of goods are subject to the standard warranty and the standard terms and conditions

published by B-TEK, LLC.

Should you have any questions regarding the Patient series floor scales, contact your local B-

TEK, LLC. scale representative.

oAbove-ground or inground models available.

oThe B-TEK Patient scales are perfect for applications where weighing patients on

or off wheelchairs is done in high volume.

oThe low profile above-ground with ramp or inground scales makes weighing

easy.

oAvailable in 36”x36” or 48”x48” sizes with 1000 lb. capacity.

oStructure carbon steel.

oSingle-ended shear beam load cell design.

Specifications

MODEL

Above-ground

Inground

Capacities

1000 lbs.

Readability

0.2 lbs.

Max. Divisions

5000e

Weighing Units

lb, kg

Platform sizes

36”x36” and 48”x48”

Construction

Carbon Steel

Load Cell Operating

Temperature

14°F - 104°F / -10°C - + 40°C

Height

1.5”

Flush to floor

Handrail

Included

Floor Mount Ramp

Included

Not Included

Floor Pit Frame

Not Included

Included

General Component Identification Above-ground

A. Base platform

B. Handrail

C. Ramp

General Component Identification Inground

A. Base Platform

B. Handrail

C. Pit Frame

Installation

Above ground Installation

It is recommended to lag bolt the ramp in place to keep the scale from moving during

use. First position the scale and ramp in the location that you intend on using the scale,

ensure that the scale is away from general traffic and that the chosen area is protected

from water, misc. debris, wind, and or vibration.

Once the location of the scale has been chosen, remove the scale from the ramp taking

care not to move the ramp. Using a black Sharpie mark the small bolt holes located on

the foot retaining plate shown in the image below.

Once these holes have been marked, remove the ramp and drill lag bolt holes where

the black Sharpie marks are located on the floor. Once the holes have been drilled

position the ramp back in place and secure it to the floor using lag bolts.

Foot retaining plate

mounting bolt holes.

Foot retaining plate

load cell feet holes.

Now that the ramp is secured to the floor the scale base can be placed back into the

ramp. Ensure that the load cell feet sit within the foot retaining plate hole as shown in

the image below.

Level the scale by adjusting the load cell feet through the access holes using a flathead

screwdriver shown in the image below.

The scale is now ready to be connected to the indicator and calibrated. See the

indicator termination section for information on connecting the scale to its indicator.

Correct foot positioning in the retaining plate.

Scale Base

Ramp

Load cell foot adjustment

In-ground Installation

The in-ground scale installation will require installation prior to concrete floor installation

or the cutting of the existing concrete floor for the scale to be installed. This is the more

labor-intensive of the two installations but is also the most desirable installation as the

scale is flush with the floor allowing the scale to be walked on/around as if it is part of

the floor.

When choosing a location for the in-ground scale it is important to consult with the

building engineers to ensure the scale is in a place that will not interfere with existing

building wiring, plumbing, etc., and at the same time ensure that the scale is away from

general traffic and that the chosen area is protected from water, misc. debris, wind, and

or vibration.

Consult with your concrete contractor to perform the pit frame installation. The pit frame

should be installed so that the top edge is even with the floor and surrounded by

concrete to ensure a solid and sound installation. Note: The pit frame will require

conduit to be run from the pit frame to a wall location directly behind the scale to run the

interconnect cable from the scale to the indicator. The image below shows the proper

installation of the pit frame.

Now that the pit frame has been completed, place the scale base in the pit frame

ensuring that there is roughly an equal amount of gap between the pit frame and scale

base around its perimeter. Note: Ensure that the interconnect cable is pulled through

the conduit at the same time the scale base is being installed to keep the cable from

tangling up or having the scale rest on the cable after its installed.

After the scale has been installed take a flathead screwdriver and adjust the scale base

feet so that it is level and even with the floor. Note: If the scale is installed and leveled

properly, you will be able to walk around the scale with a little sway but without any

metallic noise. The image below shows the location of the load cell foot adjustment

holes.

That concludes the installation of the Patient pit-style scale. For indicator termination

and calibration see the indicator termination section.

Load cell foot adjusting holes.

Indicator Termination and Calibration

It is the recommendation of B-TEK to have your scale calibrated and tested by a

certified scale company. This should not only be done for the installation but periodically

throughout the year as well. Having this done not only protects you and your patients

but also gives you peace of mind knowing your scale is in good working order and

working as it is intended to work.

Termination procedures vary from indicator to indicator. If you are using a B-TEK

indicator or indicator from another manufacturer, with your scale, please refer to the

technical manual for the termination of the indicator itself. Use the scale base

termination diagram below for terminating your indicator.

Scale J-Box PT# 864-000008

Interconnect Cable

Indicator

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere B-TEK Scales Skala Handbücher

B-TEK Scales

B-TEK Scales Centurion-DT Bedienungsanleitung

B-TEK Scales

B-TEK Scales BT-BC Bedienungsanleitung

B-TEK Scales

B-TEK Scales AX200 Bedienungsanleitung

B-TEK Scales

B-TEK Scales WorldWEIGH C200 Series Bedienungsanleitung

B-TEK Scales

B-TEK Scales DuraShield Bedienungsanleitung

B-TEK Scales

B-TEK Scales DD1010 Bedienungsanleitung

B-TEK Scales

B-TEK Scales WorldWEIGH PGE-W Series Bedienungsanleitung

B-TEK Scales

B-TEK Scales WorldWEIGH C100 Series Bedienungsanleitung

B-TEK Scales

B-TEK Scales TensionLink WS Bedienungsanleitung

B-TEK Scales

B-TEK Scales 4 Square Bedienungsanleitung

B-TEK Scales

B-TEK Scales AquaShield Series Bedienungsanleitung

B-TEK Scales

B-TEK Scales Super Sack Bedienungsanleitung

B-TEK Scales

B-TEK Scales Skynet Montage- und Wartungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung